Canon printer PIXMA MG5622 User Manual
Here you can view all the pages of manual Canon printer PIXMA MG5622 User Manual. The Canon manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 221
Don't detect mismatch of paper settings when printing from computerWhen you print documents from your computer and the paper settings on the printer driver and the printer do not match, this setting disables the message display and allows you to continue printing. To disable detection of paper setting mismatches, select this check box. Ink Drying Wait Time You can set the length of the printer rest time until printing of the next page begins. Moving the slider to the right increases the pause time,...
Page 222
Changing the Machine Settings on the LCD Changing the Machine Settings on the LCD Print settings LAN settings Device user settings PictBridge print settings Language selection Firmware update Cassette settings Reset setting About ECO settings About Quiet setting Using the Machine with the Access Point Mode 222
Page 223
Changing the Machine Settings on the LCDThis section describes the procedure to change the settings in the Device settings screen, taking the steps to specify Extended copy amount as an example.1. Make sure that the machine is turned on. 2. Select Setup on the HOME screen. LCD and Operation Panel 3. Select Device settings , then press the OK button. The Device settings screen is displayed. 4. Use the button to select the setting item, then press the OK button. The setting screen for the...
Page 224
You can select the setting menus below. Print settings LAN settings Device user settings PictBridge print settings Language selection Firmware update Cassette settings Reset setting Note • You can use the machine considering the environment, such as setting 2-sided printing as default orenabling the machine to turn on/off automatically. About ECO settings • You can reduce the operating noise when printing at night. About Quiet setting 224
Page 225
Print settings• Prevent paper abrasion Use this setting only if the print surface becomes smudged. Important • Be sure to set this back to OFF after printing since it may result in lower printing speed or lower print quality. • Extended copy amount Selects the amount of image that extends off the paper when printing in borderless (full). Slight cropping may occur at the edges since the copied image is enlarged to fill the whole page. You can change the width to be cropped from the borders of the...
Page 226
LAN settings• Change LAN Enables either wireless LAN or access point mode. You can also disable wireless LAN or access point mode. • Wireless LAN setup Selects the setup method for wireless LAN connection. Note • You can also enter this setting menu by selecting WLAN on the HOME screen. In this case, enable wireless LAN. When this menu is selected, the machine starts searching for a WPS-compatible access point. If the machine detects the access point, follow the on-screen instructions to set up...
Page 227
Communication modeInfrastructureChannelXXWireless LAN securityInactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-PSK(TKIP)/WPA2-PSK(AES)IPv4 addressXXX. XXX. XXX. XXXIPv4 subnet maskXXX. XXX. XXX. XXXIPv4 default gatewayXXX. XXX. XXX. XXXIPv6 addressXXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXXIPv6 subnet prefix lengthXXXIPv6 default gatewayXXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec settingsEnable (ESP)/Enable (ESP & AH)/Enable (AH)/DisablePre-shared...
Page 228
IPv4 default gatewayXXX. XXX. XXX. XXXIPv6 addressXXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXXIPv6 subnet prefix lengthXXXIPv6 default gatewayXXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec settingsDisablePre-shared keyXXXXXXXXXXXXXXXXPrinter nameXXXXXXXXXXXXXXXBonjour service nameXXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX ("XX" represents alphanumeric characters.) ◦ Print LAN details You can print out the network settings of the machine such as its...
Page 229
Note• When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows 8.1, Windows 8, Windows 7 and Windows Vista. WSD scan from this device Selecting Enable allows you to transfer the scanned data to the computer using WSD. Timeout setting Specifies the timeout length. ◦ Bonjour settings Setting items for LAN using Bonjour for Mac OS. Enable/disable Bonjour Selecting Enable allows you to use Bonjour to perform the network settings. Service name Specifies the Bonjour...
Page 230
Device user settings• Date display format Changes the display format of dates when printed. • Key repeat Enables/Disables continuous input by pressing and holding down the , , , , + , or - button when setting the number of copies, changing the photo displayed on the LCD, setting the zoom ratio, etc. • Device info sending setting Selects whether you will send the printer usage information to Canon server. The information sent to Canon will be utilized to develop better products. Select Agree to send...