Canon printer PIXMA iP4700 User Manual

							


123564

DE
G
F

6
Wait for about 5 minutes until the POWER lamp (green) (F) stops flashing and stays lit then operating noise stops, and go to the next step.•
Close the Top Cover (D).
If the Alarm lamp (G) flashes orange, make sure that the Print Head and the ink tanks are correctly installed.•
The printer may make some operating noises when preparing to print. This is normal operation.•
Make sure the Inner Cover (E) is closed. 
						

							
0

5

Install the Software
Quit all running applications before installation.•
To use the printer by connecting it to a computer, software including the drivers 
needs to be copied (installed) to the computer's hard disk. The installation process 
takes about 20 minutes. (The installation time varies depending on the computer 
environment or the number of applications to be installed.)
The screens below are based on Windows Vista operating system Ultimate Edition 
(hereafter referred to as "Windows Vista") and Mac OS X v.10.5.x.
Log on as the administrator (or a member of the Administrators group).•
Do not switch users during the installation process.•
It may be necessary to restart your computer during the installation pro\
cess. Follow the on-screen instructions and do not remove the Setup CD-ROM during restarting. The installation resumes once your computer has restarted.
•
Mac OS 9, Mac OS X Classic environments, or Mac OS X v.10.3.8 or earlier are not supported.•
Internet connection may be required during the installation. Connection \
fees apply.•
If the Found New Hardware or Found New 
Hardware Wizard dialog box appears:
□
Click Cancel to quit the dialog box.
Proceed from .
Remove the USB cable connected to 
your computer.
The dialog box may close. In this case, proceed 
from .
1
2
3
If you connect a USB cable to the printer before 
installation of the drivers, this screen appears. 
						

							


123465

2
A
1
12
TURN OFF THE PRINTER 
(A).
Operating noise continues for about 35 seconds until the printer turns off. 
•
The USB Port is located on the right side at the back of the printer.•
Connect the printer to the 
computer with a USB cable.
Make sure the printer is turned on.
If the program does not start automatically, double-click the CD-ROM icon in Computer or My Computer. When the CD-ROM contents appear, double-click MSETUP4.EXE.
•
Turn on the computer, then insert 
the Setup CD-ROM into the CD-
ROM drive.
The setup program will start 
automatically.
Turn on the computer, then insert 
the Setup CD-ROM into the CD-
ROM drive.
For Windows 
Vista/XP
□
If you are using 
Internet Explorer 
7 or later, you can 
use the Web print 
software Easy-
WebPrint EX. An 
internet connection 
is required for 
installation.  
(It is also possible 
to install this 
software later.) 
						

							


5

3
3
Click Run Msetup4.exe on the AutoPlay screen, then click Continue on the User 
Account Control dialog box.
Double-click the Setup icon of the CD-ROM folder to proceed to the following 
screen. Enter your administrator name and password, then click OK.
If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop.•
If you do not know your administrator name or password, click Help, then follow the on-
screen instructions.
If the User Account Control dialog box reappears in following steps, click Continue.
Windows Vista
Windows XP/2000  
						

							


123465

54
Click Install.Click Easy Install.
The drivers, application software, and on-screen manuals are installed a\
ll 
together.
For Windows Vista/XP
If you are using Internet Explorer 7 or later, you can use the Web print software 
Easy-WebPrint EX. An internet connection is required for installation. (It is also possible to install this software later.)
•
Follow any on-screen instructions to proceed with the installation.
If you want to select particular items to install, click Custom Install.• 
						

							


5

D
A
B
C

E
GF

Important Information for the Installation
Print Head Alignment□
Load a sheet of supplied speciality paper (Matte Photo Paper MP-101) in 
the Rear Tray (A) and click Execute. Do not open the Top Cover (B) while 
printing. For details, refer to “6 Loading Paper” on page 16.
If any other papers have been loaded already, remove it and load the MP-101 
paper.
When the pattern (E) shown is printed, Print Head Alignment is now complete.
In Windows, click Next on the Print Head Alignment screen.
Make sure that the Output Tray Extension (D) is extended.•
MP-101 has front and back sides. Load it so that the cut corner (C) is at the top right.•
MP-101 cannot be fed from the Cassette. Load it in the Rear Tray.•
Be sure to use MP-101 for Automatic Print Head Alignment.•
The pattern is printed in blue and black.•
If the Alarm lamp (orange) (F) flashes, press the RESUME/CANCEL button (G) on the printer to clear the error, then click Next. After the installation is complete, perform Print Head Alignment by referring to “When Printing Becomes Faint or Colors Are Incorrect” in the on-screen manual: Basic Guide.
•
Wait until the pattern printing ends (about 5 minutes).• 
						

							


123465

6
Click Exit to complete the installation.
The product serial number is required when 
registering the product. The serial number 
is located inside the printer (as shown in the 
illustration).
Necessary Information for the User 
Registration
□
If you can agree to Extended Survey Program, 
click Agree. 
If you click Do not agree, the Extended 
Survey Program will not be installed. (This has 
no effect on the printer's functionality.)
The screen does not appear on Mac OS X v.10.3.9.•
Next, read "6 Loading Paper" on page 16!
If Restart is displayed, follow the instruction to restart the 
computer.
After restarting the computer, remove the Setup CD-ROM 
and keep it in a safe place.
About Extended Survey Program□
Important Information for the Installation
When opening the Top Cover, the Print Head Holder moves automatically.• 
						

							


6

B
C
D
A

1
E
2
F
3
G
H
Loading Paper
This section explains how to load paper 
in the Cassette (A) and the Rear Tray (B).
The Cassette supports plain paper (C) only. To 
print photo paper/Hagaki (D), be sure to load it 
in the Rear Tray.
Pull out the Cassette and remove 
the Cover (E).
Pull the Tab (F) in the direction of 
the arrow and extend the Cassette.
Move the Paper Guides (G) 
and (H) to both edges. 
						

							


123456

456
I
1
2
7
Load plain paper.
Load paper with the printing 
side facing down.
Slide the Paper Guide to align with the 
actual size of the paper.
The Paper Guide will stop when it aligns 
with the corresponding mark of paper size.
Align the paper with the right edge of the 
Cassette (1), then slide the Paper Guide 
against the left edge of the paper (2).
Make sure that the height of the paper stack 
does not exceed the line (I).
Attach the Cover and insert the 
Cassette into the printer until it clicks 
into place.
There may be a little space between the Paper Guide and the paper stack.•
To print on speciality paper, be sure to load it in the Rear Tray.
• 
						

							

6
9811
L22
J1
K
123456
10
Open the Paper Support (J), and pull it up.Move the Paper Guides (K) 
to both edges.
Slide the left and right Paper Guides 
against both edges of the paper.
Load paper in portrait 
orientation with the printing side 
facing up.
For details on media sizes and types you can use, refer to "Loading Paper" in the on-screen manual: Basic Guide.
•
Printer installation is now complete!
Make sure that the height of the paper 
stack does not exceed the line (L).
Load paper in the center of 
the Rear Tray.