Canon Pixma Mx310 Quick Start Guide

7 Before Using the Machine
zScreen-saver Mode
The LCD goes out if the machine is not operated for about five minutes*.
Perform a print operation to restore the display.
* You cannot change the wait time before the LCD goes out.
Note
When you want to restore the display, perform any operation such as copying, faxing, or scanning, 
or press any button except for the ON/OFF button. When you press the ON/OFF button while the 
machine is in Screen-saver mode, the machine turns off.
 

8Before Using the Machine
Handling the Original Document
This section describes how to load the original document on the Platen Glass or the ADF.
„Original Document Requirements
The original documents you load on the Platen Glass or the ADF for copying, scanning, or faxing 
must meet these requirements:
„Loading Original Documents
Load originals to copy, scan, or fax on the Platen Glass or the ADF.
Platen GlassADF
Document type
zPaper documents
zPhotographs
zBooks
zDocuments that are not 
suitable for...

9 Before Using the Machine
zUsing the Platen Glass
1Load the original document on the Platen 
Glass.
(1)Lift the Document Cover.
(2)Load the original with the side to be copied, 
scanned, or faxed facing down on the Platen 
Glass.
Place the original in landscape orientation and 
align the upper corner of it with the alignment 
mark as shown in the figure on the right.
2Gently close the Document Cover.
Important
zDo not place any objects weighing more than 4.4 lb / 2.2 kg on the Platen Glass.
zDo not...

10Before Using the Machine
zUsing the ADF
1Remove any documents from the Platen Glass.
2Open the Document Tray.
3Load the document in the ADF.
Load the document with the side you want to copy, 
scan, or fax facing up in the ADF.
4Adjust the Document Guides to match the 
document width.
Note
Set a document on the Platen Glass if you want to scan it at optimum quality.
Note
Ensure that the edge of the document stack is in line 
with the Paper Size Mark (A) imprinted on the 
Document Tray.
(A)
 

11 Before Using the Machine
Loading Printing Paper
This section describes how to load printing paper in the Rear Tray.
zUsing Specialty Media
Canon recommends that you use Canon genuine media to ensure optimal print quality.
zPhoto Quality Media
zGlossy Photo Paper
zMatte Photo Paper
zPhoto Paper Plus Double Sided
zPhoto Paper Plus Glossy
zPhoto Paper Plus Semi-gloss
zPhoto Paper Pro
zPhoto Stickers
zMedia Suited for Business 
Documents
zHigh Resolution Paper
 

12Before Using the Machine
„Paper Handling
zRecommended Paper and Requirements
*1Paper with a Model Number is Canon specialty media. Refer to the instruction manual 
supplied with the paper for detailed information on the printable side and notes on handling 
paper. For information on the paper sizes available for each Canon genuine paper, visit our 
website. You may not be able to purchase some Canon genuine papers depending on the 
country or region of purchase. Paper is not sold in the US by Model...

13 Before Using the Machine
*3  Proper feeding of paper may not be possible at the maximum capacity depending on the type 
of paper or environmental conditions (either very high or low temperature and humidity). In 
such cases, reduce the sheets of paper you load at a time to around half (around 0.2 inches / 
5 mm in paper stack height).
*4Available only when printing from your computer.*5When loading paper in stacks, the print side may be marked as it is fed in or sheets may be 
stuck to one another...

14Before Using the Machine
„Loading Paper
1Flatten the four corners of  the paper before loading it.
ImportantzLoad A4, Letter, or Legal-sized plain paper when receiving faxes.
z If you cut plain paper to 4 x 6 / 101.6 x 152.4 mm, 5 x 7 / 127.0 x 177.8 mm, or 2.13 x 3.39 
/ 54.0 x 86.0 mm (credit card-size) for a trial print, it can cause paper jams.
z You cannot print on postcards affixed with photos or stickers.
z Always load paper in portrait orientation (A). Loading paper in landscape orientation (B)...

15
Before Using the Machine
2Prepare to load paper.
(1) Open the Rear Tray and pull out the Paper 
Support.
Put your finger in the rounded indent of the 
Paper Support and pull it out until it stops.
(2) Open the Paper Output Tray.
Put your finger in the rounded indent beside 
the Paper Output Tray and open it gently.
(3) Open the Output Tray Extension.
Open up and set the Output Tray Extension 
completely by pressing  down the hollow on its 
front side.
(4) Adjust the position of the Paper Thickness...

16Before Using the Machine
„Loading Envelopes
Use either European DL or US Comm. Env. #10-sized envelope.
1Prepare the envelopes.
zPress down on all four corners and edges of the envelopes to flatten them.
zIf the envelopes are curled, hold the opposite corners and gently twist them in the opposite 
direction.
zIf the flap of an envelope is curled, flatten it.
zIf the leading edge of an envelope is puffed up or curled, use a pen to press the envelope 
flat and sharpen the crease.
Press the envelope flat,...