Canon Pixma Mp990 Quick Start Guide

							
78
C
Network Connection
Wireless Setup Using WPS (Wi-Fi Protected Setup) 
If the timeout error screen appeared repeatedly, or if another error appeared, refer to the printed manual: Network Setup Troubleshooting.
•
When the access point is ready, press the OK button on 
the machine, then press the WPS button on the access 
point within 2 minutes.
The  Wi-Fi lamp (blue) flashes while searching for an access point.
For details on WPS, refer to the manual of your access point.
•
Next, read "Confirm 
Connection Status" on 
page 33!When the completion screen appears, press the  OK 
button, then press the HOME button (C).
The standby screen returns.
 
						

							1
BA
0Network Connection
Wired Setup
Remove the Cap (A), then connect a network device (router, etc.) with a Ethernet cable (B).
Ethernet cable
Connect to the network over a wired connection. 
A Ethernet cable is required to connect to a 
network device (router, etc.). Prepare a Ethernet 
cable.
 
						

							
32
C
D
4
Network Connection
Wired Setup
Select Device settings, then press the OK 
button.
Use the Easy-Scroll Wheel (C) to select 
Settings, 
then press the OK button. Select LAN settings, then press the OK button.
 
						

							
56
Network Connection
Wired Setup
Next, read "Confirm Connection 
Status" on page 33!
Select Change wireless/wired, then press the 
OK button.Select Wired LAN active, press the OK button, 
then press the HOME button (D).
 
						

							312
B
A
Network Connection
Select Device settings, then press the 
OK button.
Confirm Connection Status
Select LAN settings, then press the OK 
button.
Press the HOME button (A), select Settings using the Easy-Scroll 
Wheel (B), then press the OK button.
Confirm connection status after installing the machine in the target location.
•
 
						

							
C
45
Network Connection
Confirm Connection Status
Select Wireless LAN setting list or Wired LAN setting list, then press the OK button.
Select Confirm LAN settings, then press the OK 
button.
Now the machine is connected to the network. 
Next, read "[Network Connection] Install the Software" on page 35.
The machine and network device are turned on.
−
Make sure that Connection is set to  Active, then press the HOME button.
It may take a while before the connection is complete. In this case, pre\
ss the  Back button (C) and wait for about 
a minute, then display the  Wireless LAN setting list screen or Wired LAN setting list  screen again.
There is no obstacle between the machine and access point, and wireless \
communication is possible.
−
There is no microwave, refrigerator or any other object that may cause r\
adio interference nearby.
−
For wired connections, the Ethernet cable is connected properly.
− If the communication status does not improve, make sure of the following\
.
•
 
						

							1
1
Network Connection
Install the Software
Quit all running applications before installation.
•
To use the machine by connecting it to a computer, 
software including the drivers needs to be copied 
(installed) to the computer's hard disk. The 
installation process takes about 20 minutes. (The 
installation time varies depending on the computer 
environment or the number of applications to be 
installed.)
The screens below are based on Windows Vista 
operating system Ultimate Edition (hereafter 
referred to as "Windows Vista") and Mac OS X 
v.10.5.x.
Log on as the administrator (or a member of the 
Administrators group).
•
Do not switch users during the installation process.
•
It may be necessary to restart your computer during the 
installation process. Follow the on-screen instructions and 
do not remove the Setup CD-ROM during restarting. The 
installation resumes once your computer has restarted.
•
Mac OS 9, Mac OS X Classic environments, or Mac OS X 
v.10.3.8 or earlier are not supported.
• If the firewall function of your security software is turned 
on, a warning message may appear that Canon software is 
attempting to access the network. 
If such a warning message appears, set the security 
software to always allow access.
•
Turn on the computer, 
then insert the Setup 
CD-ROM into the CD-
ROM drive.
If the program does not start automatically, double-click the 
CD-ROM icon in 
Computer or My Computer.  
When the CD-ROM contents appear, double-click  MSETUP4.
EXE.
•
Turn on the computer, then insert the 
Setup CD-ROM 
into the CD-ROM drive.
Internet connection may be required during the installation. 
Connection fees apply.
•
The setup program will 
start automatically.
For Windows Vista/
XP
□
If you are using Internet 
Explorer 7 or later, 
you can use the Web 
print software Easy-
WebPrint EX. An internet 
connection is required 
for installation. (It is also 
possible to install this 
software later.)
 
						

							
2
2
Network Connection
Install the Software
Double-click the Setup icon of the CD-ROM folder to proceed to the 
following screen. Enter your administrator name and password, then click\
 
OK.
If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on 
the desktop.
•
If you do not know your administrator name or password, click 
Help, then follow 
the on-screen instructions.
Click Run Msetup4.exe on the AutoPlay screen, then click Continue on 
the User Account Control dialog box.
If the  User Account Control dialog box reappears in following steps, click 
Continue.
Windows Vista
Windows XP/2000 
 
						

							
43
Network Connection
Install the Software
Click Install.
Click Easy Install.
The drivers, application software, and on-screen manuals are installed a\
ll 
together.
If you want to select particular items to install, click  Custom Install.
•
If you are using Internet Explorer 7 or later, you can use the Web print software 
Easy-WebPrint EX. An internet connection is required for installation. (It is also 
possible to install this software later.)
•
For Windows Vista/XP
When installing the XPS Printer Driver, select the MP Drivers at the same time.
• You can install the XPS Printer Driver from 
Custom Install. (Windows Vista SP1 or 
later.)
•
The XPS Printer Driver is a printer driver suitable for printing High Dy\
namic Range 
images (full 16-bit workflow) using Easy-PhotoPrint Pro.
• For Windows Vista
 
						

							
56
Network Connection
Install the Software
Select Use the printer on network, then click Next.
Follow any on-screen instructions to proceed with the software installat\
ion.
•
Read the License Agreement screen carefully and click  Yes.