Canon Pixma Ip90 Quick Start Guide

							Printing Maintenance57
Aligning the Print Head
If ruled lines are displaced or the print result is unsatisfactory, Print Head alignment is 
required.
ì
1With the printer on, load a sheet of Letter-sized plain paper in the printer.
Move the Paper Thickness Lever (gray) to the right position.
2Open the Printer Properties dialog box.
See Opening the Printer Properties Dialog  Box Directly from the Start Menu on 
page 29.
3Print the pattern.
(1)Click the  Maintenance  tab. 
(2)Click Print Head Alignment .
(3)Click Print Head Alignment .
When the confirmation message is 
displayed, click  OK.
The Pattern will be printed.
Note Click 
Check Setting  to 
print the current 
setting and finish the 
operation.
QSG_Aligning_Print_Head.fm  Page 57   Monday, October 25, 2004  2:46 PM
 
						

							Printing Maintenance
58
4 Align the Print Head.
(1)Look at the print out. From the patterns, select the most even, least irregular 
patterns.
 
 
(4)When the confirmation message is displayed, click  OK.
Note
If it is difficult to pick up the best
 pattern on Column H, pick the setting 
that produces the least noticeable vertical white stripes.
(4)After the pattern is printed, click  Ye s.
(2)Enter the numbers.
(3)Click  OK.
Less noticeable white stripes More noticeable white stripes
QSG_Aligning_Print_Head.fm  Page 58   Monday, October 25, 2004  2:46 PM
 
						

							Printing Maintenance59
1With the printer on, load a sheet of Letter-sized plain paper in the printer.
Move the Paper Thickness Lever (gray) to the right position.
2Open the BJ Printer Utility dialog box.
(1)Double-click the hard disk icon where the printer driver was installed, the 
Applications  folder, and the  Utilities folder.
(2) Double-click the  Printer Setup Utility  icon.
If you are using an OS other than Mac OS X v.10.3, double-click the  Print Center 
icon.
(3) Select  iP90 from the  Name list and click  Utility or Configure .
(4) Select  iP90 from the  Product list and click  Maintenance.
3Print the pattern.
NoteThe BJ Printer Utility cannot be 
used with Bluetooth communication.
(1)Select  Te s t  P r i n t  from 
the pop-up menu.
(2) Click  Print Head Alignment .
(3)Click  Print Head Alignment .
The Pattern will be printed.
Note Click 
Check 
Setting  to print 
the current setting 
and finish the 
operation.
QSG_Aligning_Print_Head.fm  Page 59   Monday, October 25, 2004  2:46 PM
 
						

							Printing Maintenance
60
4Align the Print Head.
(1)Look at the print out. From the patterns, select the most even, least irregular 
patterns.
Note If it is difficult to pick up the best pattern on Column H, pick the 
setting that produces the least noticeable vertical white stripes.
(2)Enter the numbers.
(3)Click 
Send.
Less noticeable white stripes More noticeable white stripes
QSG_Aligning_Print_Head.fm  Page 60   Monday, October 25, 2004  2:46 PM
 
						

							Printing Maintenance61
Replacing an Ink Tank
If the print result is not improved after maintenance such as Print Head 
cleaning, an ink tank runs out of ink.  Replace the ink tank with a new one. 
When replacing an ink tank, check the model number very carefully. 
The printer will not print properly if the wrong ink tank is used, or installed in 
the incorrect position.
„ Replacing an Ink Tank
When an ink tank runs out of ink, replace it using the following steps.
1Ensure that the printer is turned on, and then open the Print Head Cover.
The Print Head Holder moves to the center.
Black: BCI-15 Black Color: BCI-16 Color
QSG_Replacing_an_Ink_Tank.fm  Page  61  Monday, October 25, 2004  2:47 PM
 
						

							Printing Maintenance
62
2Remove the empty ink tank.
(1)Push the tab.
(2) Remove the ink tank.
Then lift it from its slot.
Do not touch the Lock lever; remove only the ink tank.
3Prepare a replacement ink tank.
(1)Unpack a new ink tank and remove the orange Protective Cap.
Important
• Handle ink tanks carefully to avoid staining your clothes or 
surrounding area.
• Discard empty ink tanks according to the local laws and regulations  regarding disposal of consumables.
Important • Do not re-attach the Protective Cap once you have removed it.
• Once the Protective Cap is removed, do not touch the open ink port.
Protective Cap
QSG_Replacing_an_Ink_Tank.fm  Page  62  Monday, October 25, 2004  2:47 PM
 
						

							Printing Maintenance63
4Insert the ink tank.
(1)Insert a new ink tank with it slightly slanted.
(2) Push down on the   on the ink tank until it clicks into place.
5Close the Print Head Cover.
The Print Head Holder moves to the right.
Important When an ink tank is replaced, the ink counter must be reset.
See Resetting the Ink Counter  on page 64
Note • To maintain optimal print quality, use an ink tank within six months 
of its first use.
• Once an ink tank has been used, do not remove it from the printer  and leave it out in the open. This will cause the ink tank to dry out 
and the printer may not function properly if it is reinstalled.
• Color ink consumption may occur even when black-and-white or  grayscale printing is specified.
Color ink is consumed in the head cleaning and deep cleaning, 
which are necessary to maintain the printer’s capabilities.
• When an ink tank runs out of ink, replace the ink tank with a new one  immediately.
If printing is continued with no ink in the ink tank, a problem may 
occur. And, the Low Ink Warning dialog which tells the exchange 
time of the ink tank cannot be indicated properly.
QSG_Replacing_an_Ink_Tank.fm  Page  63  Monday, October 25, 2004  2:47 PM
 
						

							Printing Maintenance
64
„Resetting the Ink Counter
When an ink tank is replaced, the ink counter must be reset.
The low ink warning is only displayed properly if the ink counter is reset.
Message Prompting Confirmation of Ink Tank Replacement
If an ink tank is removed, the printer will output a message prompting you to confirm 
replacement of the ink tank at the start of the next print job.
When an ink tank has been replaced, follow the procedure below to reset the ink 
counter. The low ink warning is only displayed properly if the ink counter is reset.
1Check the message, and click Yes.
Mistakenly clicking  No, instead, will prevent the lo w ink warning from functioning 
properly. If this happens, be sure to open the driver’s Properties dialog box and 
manually reset the ink tank counter in the Maintenance tab.
See  Resetting the Ink Counter in the Printer Properties dialog box  on page 65
2Select the replaced ink tank, and click OK.
The dialog box allows you to select the replaced ink tank.
When both black and color ink tanks have been replaced, select both Black and 
Color.
If you have not replaced the ink tank with a new one, click  Cancel.
Important
If infrared communication is perfor med in Windows XP or Windows 2000, 
the printer will not output the message asking for confirmation of ink tank 
replacement.
This is why it is important to open th e printer drivers Properties dialog box 
and manually reset the ink tank counter in the Maintenance tab whenever 
an ink tank is replaced.
QSG_Replacing_an_Ink_Tank.fm  Page  64  Monday, October 25, 2004  2:47 PM
 
						

							Printing Maintenance65
Resetting the Ink Coun ter in the Printer Properties dialog box
1Open the Printer Properties  dialog box and click the  Maintenance tab.
See Opening the Printer Properties Dialog  Box Directly from the Start Menu on 
page 29
2Click  Ink Counter Reset .
3Select the newly installed ink tank, then click  OK. 
1Open the BJ Printer Utility dialog box.
(1) Double-click the hard disk icon where the printer driver was installed, the 
Application  folder, and the  Utilities folder.
(2) Double-click the  Printer Setup Utility  icon.
If you are using an OS other than Mac OS X v.10.3, double-click the  Print Center 
icon.
(3) Select  iP90 from the  Name list and click  Utility or Configure .
(4) Select  iP90 from the  Product list and click  Maintenance.
Note
The BJ Printer Utility cannot be 
used with Bluetooth communication.
QSG_Replacing_an_Ink_Tank.fm  Page  65  Monday, October 25, 2004  2:47 PM
 
						

							Printing Maintenance
66
2Reset the Ink Counter.
(2) Click Ink Counter Reset .
(1) Select 
Remaining ink level setting  
from the pop-up menu.
(4) Click  OK.
(3)  Select the newly installed ink tank.
QSG_Replacing_an_Ink_Tank.fm  Page 
66  Monday, October 25, 2004  2:47 PM