Canon Pixma Ip4840 User Guide

Advanced Guide > Printing from a Computer > Printing with Other Application Software > Overview of the Printer Driver
> Canon IJ Status Monitor 
P411 
Canon IJ Status Monitor 
If you are using the XPS printer driver, replace Canon IJ Status Monitor with Canon IJ XPS Status
Monitor when reading this information.  
The Canon IJ Status Monitor is an application softw are that shows the status of the printer and the
progress of printing on the W indows screen. You wil l know the status of the printer with...

Advanced Guide > Printing from a Computer > Printing with Other Application Software > Overview of the Printer Driver
> Canon IJ Preview 
P412 
Canon IJ Preview 
The Canon IJ Preview is an application software tha t displays what the print result will look like before a
document is actually printed.  
The preview reflects the information that is set wi thin the printer driver and allows you to check the
document layout, print order, and number of pages.  You can also change the media type and paper...

Advanced Guide > About Disc Label Printing 
About Disc Label Printing 
Printing a Disc Label
Troubleshooting
Page top
Page 333 of 468 pages
About Disc Label Printing
.ownloadedtfromtManualsPrinterDcomtManuals  

Advanced Guide > About Disc Label Printing > Printing a Disc Label 
Printing a Disc Label 
Items to Prepare
Cautions W hen Printing on the Disc Label
Attaching/Removing the Disc Tray
Printing on the Disc Label
Printing with CD-LabelPrint from the Computer
Printing Area
Page top
Page 334 of 468 pages
Printing a Disc Label
.ownloadedtfromtManualsPrinterDcomtManuals  

Advanced Guide > About Disc Label Printing > Printing a Disc Label > Items to Prepare
D018
Items to Prepare
The following items are needed to print onto the printable disc:
Disc Tray
G is on the upper side.
3.15 inches / 8 cm Disc Adapter
Needed only when printing on 3.15 inches / 8 cm pri ntable discs.
Attached to the Disc Tray when shipped.
Printable Discs 
Obtain a 4.72 inches / 12 cm or 3.15 inches / 8 cm  printable disc with a label surface compatible
with inkjet printing.
A printable disc differs...

Advanced Guide > About Disc Label Printing > Printing a Disc Label > Cautions W hen Printing on the Disc Label
D001
Cautions When Printing on the Disc Label
Be sure to use the Disc Tray supplied with this pri nter. It has an G on the upper side.
Do not print on printable discs that are not compatible  with inkjet printing. The ink will not dry and
may cause problems with the disc itself or devices  which the disc is loaded onto.
Do not print on the printable discs recording surface. Doing so will make...

Advanced Guide > About Disc Label Printing > Printing a Disc Label > Attaching/Removing the Disc Tray
D013
Attaching/Removing the Disc Tray 
Attaching the Disc Tray
Important
Do not attach the Disc Tray until the message asking you to load the printable disc is
displayed. Doing so can damage the printer.
1.Open the Paper Output Tray (A).
2.Make sure that the message asking you to load the p rintable disc is displayed, then open
the Inner Cover (B).
3.Place the printable disc on the Disc Tray.
Important...

1.Align the protrusions on both edges of the 3.15 inc hes / 8 cm Disc Adapter with
indentations on the Disc Tray.
2. Place the 3.15 inches / 8 cm printable disc on the  Disc Tray with the printing
surface facing up.
4.Attach the Disc Tray to the printer.
Note
The Disc Tray may be ejected after a specified peri od of time has elapsed. In this case,
follow the on-screen instructions to attach the Dis c Tray.
5.Insert the Disc Tray straight until the arrow () on the Inner Cover is almost aligned with
the...

1.Pull out the Disc Tray.
2.Close the Inner Cover.
Important
If the Inner Cover is opened, you cannot print on paper as it will not feed properly. Make
sure that the Inner Cover is closed.
3.Remove the printable disc from the Disc Tray.
Important
Do not touch the printing surface when removing the  disc from the Disc Tray.
Note
Dry the printing surface sufficiently before removing the disc. If you see printing on the
Disc Tray or the transparent parts on inner or oute r diameter of the printable disc,...

3.15 inches / 8 cm printable disc:1. Remove the 3.15 inches / 8 cm Disc Adapter from the Disc T
ray.
2. Remove the 3.15 inches / 8 cm printable disc from the D isc Tray.
Important
The Disc Tray cannot be used if it becomes warped. Be sure to keep the Disc Tray on a flat
place.
Page top
Page 340 of 468 pages
Attaching/Removing the Disc Tray
.ownloadedtfromtManualsPrinterDcomtManuals