Canon network camera VBS900F User Manual

51
Setting Page
4
General Upload
(1) [Upload] 
Select [Upload Disabled], [HTTP Upload] or [FTP 
Upload] for the upload method.
(2) [Video Format]
Select the [JPEG] or [H.264(1)] format for video you 
want to upload. 
If [H.264(1)] is selected, video is uploaded with the 
settings defined under [Video] > [H.264(1)] (p. 46).
 [H.264(2)] cannot be used.
(3) [Frame Rate] 
Enter the maximum frame rate of video to be 
uploaded. This setting can only be made when 
[JPEG] is selected for [Video Format].
(4)...

52
– From the Intelligent Function Setting Tool [Event] tab > 
disable [ON Event Operation], [OFF Event Operation] or 
[Detected mode Operation] (p. 104). 
– If [External Device Input Event] is enabled, disable [Active 
Event Operation], [Inactive Event Operation], or [Ongoing 
Active Event Operation] (p. 57). 
– If [Timer Event] is enabled, increase the value in [Repeat 
Interval] (p. 58). 
HTTP Upload
The HTTP upload function sends notifications via HTTP or 
via HTTP with attached videos, depending on...

[Upload] Setting HTTP/FTP Upload and E-mail Notification
53
4
Setting Page
[User Setting] 
Video is uploaded according to the file naming 
method specified in [Subdirectory Name to Create] 
and [File Name to Create]. 
[Subdirectory Name to Create], [File Name to 
Create] 
If file naming is set to [User Setting], enter the 
subdirectory name to be created as well as the 
name of the created file (using up to 127 
characters). Parameters can be specified in the 
entry with the “%” character (p. 144).
(7)...

54
Video Server
(1) [Maximum Number of Clients] 
Set the maximum number of clients that can be 
connected to the camera at the same time. Up to 30 
clients can be set. 
If 0 is set, connection is prohibited except for the 
Administrator. 
(2) [Camera Control Queue Length] 
Set the maximum queue length for clients requesting 
camera control privilege from the viewer. The 
maximum number is 30. Enter an integer from 0 to 30. 
If 0 is set, camera control is prohibited except for the 
Administrator. 
(3)...

[Server] Setting the Video Server, Audio Server and HTTP Server
55
4
Setting Page
HTTP Server
(1) [Authentication Method] 
Set the authentication method used with the HTTP 
server to [Basic Authentication] or [Digest 
Authentication]. 
(2) [HTTP Port] 
Set the HTTP port number to 80 or in the range of 
1024 to 65535. 
Normally [80] (factory default setting) is used. 
(3) [HTTPS Port] 
Set the HTTPS port number to 443 or in the range of 
1024 to 65535. 
Normally [443] (factory default setting) is used....

56
Video Record Setting
(1) [Video Record Action]
Select the destination of a video recorded when an 
event occurs. To record to a server selected on the 
[Upload] in the setting page, select [Upload] and to 
record to a memory card inserted in the camera, 
select [Record to Memory Card].
Note
The size and format of video recorded according to the [Video 
Record Action] settings are as follows:
Settings must be made in the above setting page to make 
an actual video recording.Volume Detection
(1) [Volume...

[Event] Setting Video Record, Volume Detection, External Device Output/Input and Timer
57
4
Setting Page
necessary to set the presets with the Preset Setting 
Tool under Admin Tools (p. 90). If there is no need for 
additional camera operation, select [None]. 
(9) [Video Record]
Specify the video record action. If [Enable] is 
selected, video will be transmitted to the destination 
selected in [Video Record Action] (p. 56) when a 
volume detection event occurs.
(10)[E-mail Notification] 
Select the...

58
(4) [Inactive Event Operation] 
Select the operation to be performed upon an inactive 
event. If [Enable] is selected, (6) [Preset], (7) [Video 
Record] and (8) [E-mail Notification] will be executed 
according to their settings upon an inactive event.
(5) [Ongoing Active Event Operation]
Select the operation to be performed while an active 
event is in progress.
If [Enable] is selected, (7) [Video Record] and (8) [E-
mail Notification] will be executed according to their 
settings during the active...

[Event] Setting Video Record, Volume Detection, External Device Output/Input and Timer
59
4
Setting Page
Select [Disable] to disable Day/Night Mode switching.
Note
When using timers that run continuously for 24 hours with a 
[Repeat Interval] of 30 seconds or less, set the timer start and 
end times so the timers can run continuously.
Example:
Important
 [Day/Night Mode Switching] can only be set in [Timer 1].
 [External Device Output] and [Day/Night Mode Switching] do 
not support [Repeat Interval]....

60
Authorized User Account
(1) [User Name], [Password] 
Enter the user name and password and then click 
[Add]. The authorized user will be added to the user 
list. 
The user name can consist of up to 15 (single-byte) 
characters using A to Z, a to z, 0 to 9, “-” (hyphen) and 
“_” (underscore). 
The password can consist of 6 to15 (single-byte) 
ASCII characters (space or printable characters). 
(2) [User List] 
A list of authorized users is shown. User authorities 
can be set for these users. Up to 50...