Canon network camera VBH651V User Manual

							Camera Setup
2
41
The [Initial Settings] top page will be displayed.
After the camera restarts, the Setting Page is displayed and you can configure the settings.
1Launch the web browser.
2Enter 192.168.100.1, and press the Enter key.
3Enter the administrator name and administrator password, and click [Apply]. 
						

							42 
						

							Chapter
 
Setting the Camera Angle
After installing the camera, set the camera angle while checking the video displayed in [Camera] > [Camera 
Angle] on the Setting Page.
H651 
						

							44
Adjust the camera angle when installing the camera or after changing the installation location.
The camera angle settings are configured by accessing  the Setting Page (P. 86).
Step 1 Configuring the Camera Before Setting the Camera Angle
Set the digital zoom, image stabilizer, and  image flip, which affect the camera angle.
[Digital Zoom] (P. 105) and [Image Stabilizer] (P. 105) in [C amera] > [Camera] > [Camera Control] on the Setting Page. 
[Image Flip] (P. 107) in [Camera] > [Camera]  > [Installation Conditions] on the Setting Page.
Step 2 Setting the Camera Angle and Focus
Sets pan, tilt, zoom, rotation and focus.
[Camera] > [Camera Angle]  (P. 45) on the Setting Page.
Flow for the Setting of the Camera Angle
Important
[Camera] > [Camera Angle] on the Setting Pa ge is for camera installation adjustment and is not intended for regular use. It may  damage 
the camera if used frequently. 
						

							Setting the Camera Angle
3
45
Select [Camera] > [Camera Angle] on the Setting Page to set pan, tilt, zoom, rotation and focus.
Note
[Camera Angle] can be also launched from the Camera Management Tool. For details, please refer to “Camera Management Tool User 
Manual”.
Camera Angle Screen Composition
(1) Video Display Area
Camera video is  displayed here.
(2) Control Assist Display Displays the available directions for the camera with  dotted lines when performing pan/tilt operations.
(3) [Pan] Buttons Pan the camera.
(4) [Tilt] Buttons Tilt the camera.
(5) [Zoom] Buttons Zoom the camera.
(6) [Rotation] Buttons Rotate the camera.
(7) [Rotation] Slider Click on the slider or drag the s lider to rotate the camera angle.
(8) [Reconnect] Buttons Reconnects to the camera. Can be operat ed when not connected to the camera.
Setting the Camera Angle
Important
 When starting to set the camera angle, the Viewers and  recording software connected to the camera are disconnected.
 Connections to a single camera are limited to 30 minutes. Since the camera is automat ically disconnected after 30 minutes elapse, 
click the [Reconnect] button to reconnect to the camera  if you have not finished setting the camera angle.
 Multiple computers cannot simultaneously connect to a single camera, using the [Camera Angle] tool.
(3)
(7) (4)
(5)
(6)
(14)
(4)
(1)
(2)
(3)
(9)
(15)
(8)
(10)
(13)
(12)
(11) 
						

							46
(9) Control Assist CorrectionIf you click [Exec] when the control assistance display  does not match the actual camera angle, an operation is 
performed which confirms the actual camera angle, and  the position of the control assistance display is 
automatically corrected.
Correction takes approximately one minute.
(10) [Camera Settings] Operate the focus (P. 109).
(11) Digital Zoom Range Displayed when [Digital Zoom] is set to [Enable] in [Camera] > [Camera] > [Camera Control] on the Setting 
Page.
(12) [Zoom] Slider Click on the slider or drag t he slider to zoom the camera.
(13) [Control Assist Display] Buttons Switch whether to display control assist in the video display area.
(14) [Apply] Click [Apply] to apply the changed settings.
(15) [Clear] Click [Clear] to revert to the previous settings.
Setting the Camera Angle and Zoom
You can set the camera angle and zoom us ing the video display area or buttons.
Configuring the Settings with th e Operation Buttons and Sliders
Set the angle and zoom using the [Pan],  [Tilt], [Zoom], and [Rotation] buttons.
These buttons operate while pressed and stop when released.
To operate with the [Zoom] slider, drag  the slider to change the camera zoom ratio according to the position on the 
slider.
If you set [Digital Zoom] to [Enable] in  [Camera] > [Camera] > [Camera Control]  on the Setting Page, the digital zoom 
area (yellow) is displayed and digital zoom becomes available.
The higher the digital zoom ratio, the lower the video quality becomes.
Important
If you change the camera angle after configuring the intelligent  function, privacy mask, preset, and ADSR, those settings must  be 
configured again.
  Pans left or right.
  Tilts up or down.
  Operate the zoom ratio (telephoto/wide-angle). 
						

							Setting the Camera Angle
3
47
To operate the camera angle using the [Rotation] slider, click the slider or drag the tab to adjust the camera to an 
angle where the subject in the video is horizontal.
 Setting Camera Angle by Clicking Video
If you click anywhere in the video display area, the camera angle will change to center on that location.
If you click outside the pan or tilt r ange, however, the camera angle will only  change for the one which is within its 
range.
Note
If the camera moves differently than the intended operation, or  if settings in the full range displayed by control assist cannot be 
made, control assist may be out of alignment with the actual camera angle. In this case, click [Exec] for [Control Assist Corre ction], 
and set the camera angle again.
Setting the Focus
You can automatically or manually focus on the subject, or fi x the focus at infinity. When manually operating the focus, you 
can use the One-shot AF feat ure to focus on the subject.
For precautions, etc. regarding the focus, pl ease refer to the “Important” and “Note” sections of [Camera] > [Initial Setting] 
> [Camera Settings] > [Focus] on the Setting Page (P. 110).  
Controls the rotation.
Digital Zoom Range 
						

							48
[Focus]
Selects the focus.[Auto]
Automatically adjusts the focus.
[Manual]
 You can click and hold the [Near] and [Far] buttons in [Adjust  Focus] to adjust the focus in the near and far directions. 
 When you click [Exec] in [One-shot AF], the camera wi ll focus once using autofocus and then switch to manual mode.
[Fixed at infinity]
Fixes the focus at infinity, where camera focus adjustment is not required.
Note
If you click [Apply] to apply changed camera angle settings, the  zoom and focus settings are also reflected in [Initial Settings]. 
						

							Chapter
 
Camera Viewer
Use the web browser to access the Viewer in the camera to perform camera operations, view live video, and 
check the status of events. 
						

							50
You can start the Camera Viewer to switch users and check/configure the status of the camera as well as the video display.
Note
If you open another window or tab to access the camera while an aut henticated web page is displayed, the authentication information of 
the displayed web page may be discarded.
In this case, enter the authentication information again.
Launching the Camera Viewer
You can enter the IP address set with the Camera Managemen t Tool (P. 38) directly into a web browser to display the 
Setting Page of the camera, and star t the Viewer from the Setting Page.
Note
For details on settings in the Camera Management Tool, please refer to “Camera Management Tool User Manual”.
The authentication screen for Setting Page will be displayed.
The Setting Menu is displayed.
Note
You can set [Basic] > [Viewer] > [General] > [Default Page] to [Dis play Viewer] in the setting menu to set the Viewer as the default 
page (P. 104).
Viewing Video with the Camera Viewer
1
Launch the web browser.
2Enter the IP address, and press the Enter key.
3Enter the Administrator Name and Administrator Password (P. 37) and click [OK].
4Click [Viewer].