Canon network camera VBH651V User Manual

Setting Page
5
141
Move the preview frame by dragging it and change its size by dragging the handles () positioned on its four 
sides.
Note
To discard changes and restore settings saved to the camera, cl ick [Clear]. However, note that mask area settings that have not 
been saved in the camera by clic king [Apply] are all discarded.
The changed privacy mask area is saved to the camera.
Deleting a Privacy Mask from the Camera
Click [Delete] for [Mask area] in the privacy mask that you want to delete,...

142
Settings for audio input from the microphone connected to the camera and audio output from the Viewer. The output sound 
clip used when an event is triggered can also be registered.
General Sound
Set the audio input/output volume, e cho cancellation and microphone type.
[Input Volume]
Enter the input volume from the microphone connected to the camera.
This is applied when [Server] > [Audio  Server] > [Audio Transmission from th e Camera] (P. 148) is set to [Enable].
[Output Volume]
Enter the output...

Setting Page
5
143
[Audio Input]
Select the type of microphone connected to the camera.
Sound Clip Upload 1 to 3
You can upload up to three sound clips for playback when an event is triggered.
Note
The sound clip is used when audio playback is set in [Event] >  [External Device Input] (P. 156) or [Event] > [Intelligent Function] > the 
[Event] tab (P. 184).
[Browse File]
Specify the sound clip to upload and click [Add].
To be able to upload a sound clip, it must satisfy the following requirements....

144
Settings for HTTP server, SNMP server, FTP server usage or WS-Security time checks.
HTTP Server
Set the authentication method and HTTP port number.
[Authentication Method]
Select an authentication method for use by the HTTP server.
[HTTP Port]
Enter an HTTP port number.
Normally use [80] (factory default setting).
[HTTPS Port]
Enter an HTTPS port number.
Normally use [443] (factory default setting).
SNMP Server
Configure the necessary settings to use SNMP.
Note
 The camera information referenced from...

Setting Page
5
145
[Administrator Contact Information]
Enter contact information (e-mail address, etc.) for the administrator of the camera. Setting information can be referenced 
by the SNMP manager.
[Administration  Function Name]
Enter the camera name used for administration. Settin g information can be referenced by the SNMP manager.
If left blank, the camera model name will be used.
[Installation Location]
Enter information regarding the installation location of this camera. Setting information can...

146
WS-Security
[Check Time on Authentication]
Select whether to check the time information of data transmitted by the client. 

Setting Page
5
147
Settings for clients that can connect to a video server.
Video Server
[Maximum Number of Clients]
Enter the maximum number of clients that can be connected to the camera at the same time.
If set to [0], only administ rators will be able to connect.
[Camera Control Queue Length]
Enter the maximum queue length for clients requesting  camera control privileges from the Camera Viewer.
If set to [0], only administra tors can queue for camera control.
[Maximum Connection Time (sec.)]
Enter...

148
Settings for audio transmission from the camera to the computer, and audio reception from the computer to the camera.
Audio Server
[Audio Transmission from the Camera]
Select to transmit audio from the microph one connected to the camera to the Viewer.
[Voice Activity Detection]
Select whether to detect when there is  no sound coming from the microphone.
When set to [Enable], audio data transmission will pause while th ere is no sound input from the camera. This can reduce the 
load on the network...

Setting Page
5
149
Set the video and audio transmission using RTP.
RTP Server
Enable RTP, and set the RTSP authentication method and port number.
[RTP]
Select this to enable or disable RTP.
[RTSP Authentication Method]
Select an authentication method for RTSP. Since the RTSP authentication method is  configured independently of the HTTP 
authentication method, you need to  configure each authentication method.
[RTSP Port]
Enter the RTSP port number.
Normally use [554] (factory default setting).
Audio...

150
RTP Streaming 1 to 5
You can set each stream for RTP stream transmission in an RTP Streaming 1 to RTP Streaming 5 session.
[Video Size]
Select the video format (JPEG or H.264 ) and video size for the RTP stream.
The video sizes for JPEG will vary dependin g on the [Video Size Set] settings (P. 101).
The video sizes for H.264 will be determined according to  the [H.264(1)] and [H.264(2)] settings in [Video] (P. 102).
In addition, [H.264(2)] cannot be set for multiple RTP streams.
[Frame Rate]
Enter...