Canon network camera VBC50FSi User Manual

7-13
Appendix
Log Messages
●S011 (err)
Message Execution failure: Access to the data directory was denied.
Explanation The drive for storing files does not exist or the service could not log \
on to the remote host specified as Data Directory.
 ●S015 (warning)
Message The task was running longer than the execution interval.
Explanation The specified task did not end before the start time of the next task.
● S019 (err)
Message The account information is invalid.
Explanation The user information cannot be...

7-14
Log Messages
●D001 (info)
Message Download has started.
●D002 (info)
Message Download is completed: image=%1audio=%2 [delete:image=%3
audio=%4]
%1 No. of downloaded images
%2 No. of downloaded audio files
%3 No. of deleted images
%4 No. of deleted audio files
● D003 (warning)
Message Download has aborted.
●D010 (err)
Message Not enough memory.
●D011 (err)
Message Communication error.
●D020 (err)
Message Cannot start because the server is recreating the list of the recorded
pictures.
●D021 (err)...

7-15
Appendix
Log Messages
●D025 (err)
Message Could not perform data deletion and audio file download because login
as Administrator failed.
●D029 (err)
Message Download is aborted because of insufficient free space.
●D035 (info)
Message The number of downloaded data has reached to the limit.
Explanation Output when the download limit for a single download has been reached.
● D050 (err)
Message Failed to start the downloader.
●D051 (err)
Message Downloader was stopped due to time-out.
●D052 (err)...

7-16
VB-C50FSi/VB-C50FiVideo signal Conforms to NTSC/PALImage Sensor 1/4-inch CCDNumber of pixels NTSC Effective 340,000PAL Effective 400,000
Synchronization InternalScanning Method 2 : 1 interlacedMin. subject illumination Day mode: 1Lux (F1.6, color, NTSC: 1/30 sec PAL: 1/25 sec)Night mode: 0.35Lux (F1.6, monochrome, NTSC: 1/30 sec PAL: 1/25 sec)
Imaging modes Day mode/Night modeFocusingDay mode/Night mode: Auto/Manual Wide-angle: 0.01m(0.03ft) to  /Telephoto: 1.6m(5.25ft) to Night mode (with infrared...

7-17
Appendix
Specifications
+3.3V
0.1 µF
10k
Ω 10kΩ 10k
Ω
Internal controllerInput terminals 
IN+, IN–
Output terminals 
OUT A, OUT B, OUT C
+
–
External Device I/O Terminals
You can use Input/Output external devices together with the Multi-Termin\
al Module VB-EX50.
External Device Input Terminals (IN+, IN–)
The external device input terminals consist of 2 terminals (IN+, IN-). The ‘–’ terminal is grounded
on the inside of the main unit. By connecting 2 cables to the + and ‘\
–’ terminals and then...

7-18
Note
●Install the Viewer for PC from the “VBToolsInstall.exe” file on th\
e supplied CD-
ROM ( → P.2-13).
● The User’s Manual for the viewer software is provided on the supplied\
 CD-ROM
(Viewer-E.pdf).
● To connect the VB-C50FSi/VB-C50Fi to the Internet, you require a leased \
line connection
to an Internet service provider or a LAN-type dial-up IP connection. If \
you are using a
LAN-type dial-up connection, check that the connection supports bidirect\
ional calling.
System Configuration
This...

7-19
Appendix
Sample Network Configurations
This section describes some typical installation modes for the VB-C50FSi\
/VB-C50Fi.
Be sure to assign an IP address to the VB-C50FSi/VB-C50Fi that matches y\
our environment.
This example shows the VB-C50FSi/VB-C50Fi connected to a LAN by Ethernet\
. In this
configuration, videos can be seen by viewers in the same Ethernet segmen\
t as the VB-C50FSi/
VB-C50Fi and by viewers with access to that segment.
Sample Configuration in an ISP Environment
This example...

7-20
Upgrading the Firmware Remotely
Note
●Do not turn the power off until you have confirmed that the VB-C50FSi/VB\
-C50Fi
has restarted. Turning the power off before completion may prevent it fr\
om starting
up properly.
● Upgrading the firmware deletes all saved web page data ( → P.5-8). Back up your
data before using this function.
Get the new firmware from Canon Web site, and upgrade in command prompt.\
 The firmware file
is called “Firmware_new.bin” and is saved on your PC in “My Doc\
uments”.
1....

7-21
Appendix
Restoring the Factory Default Settings
Since the VB-C50FSi/VB-C50Fi supports a wide variety of functions, we re\
commend that you
make a note of the settings for each function (→ P.7-23).  If you want to redo the settings from the
beginning because you have forgotten them or for some other reason, firs\
t restore the factory
default settings.
* Please refer to page 7-23 for more about the factory default settings.\
Restoring the Factory Default Settings from the Administration Tools Pag\...

7-22
Restoring the Factory Default Settings
Note
●Do not turn the VB-C50FSi/VB-C50Fi power off while the Restoring operati\
on.
Turning the power off before completion may prevent it from starting up \
properly.
● If you click the “OK” button at this point, it will not possible t\
o abort the process to
restore the default settings. Click the “Cancel” button if you do \
not wish to restore
the default settings.
● Using “Restore Settings” deletes all saved web page data ( → P.5-8). Back up your
data...