Home > Canon > Camera > Canon network camera VBC50Fi User Manual

Canon network camera VBC50Fi User Manual

Here you can view all the pages of manual Canon network camera VBC50Fi User Manual. The Canon manuals for Camera are available online for free. You can easily download all the documents as PDF.

Page 221

7-13
Appendix
Log Messages
●S011 (err)
Message Execution failure: Access to the data directory was denied.
Explanation The drive for storing files does not exist or the service could not log \
on to the remote host specified as Data Directory.
 ●S015 (warning)
Message The task was running longer than the execution interval.
Explanation The specified task did not end before the start time of the next task.
● S019 (err)
Message The account information is invalid.
Explanation The user information cannot be...

Page 222

7-14
Log Messages
●D001 (info)
Message Download has started.
●D002 (info)
Message Download is completed: image=%1audio=%2 [delete:image=%3
audio=%4]
%1 No. of downloaded images
%2 No. of downloaded audio files
%3 No. of deleted images
%4 No. of deleted audio files
● D003 (warning)
Message Download has aborted.
●D010 (err)
Message Not enough memory.
●D011 (err)
Message Communication error.
●D020 (err)
Message Cannot start because the server is recreating the list of the recorded
pictures.
●D021 (err)...

Page 223

7-15
Appendix
Log Messages
●D025 (err)
Message Could not perform data deletion and audio file download because login
as Administrator failed.
●D029 (err)
Message Download is aborted because of insufficient free space.
●D035 (info)
Message The number of downloaded data has reached to the limit.
Explanation Output when the download limit for a single download has been reached.
● D050 (err)
Message Failed to start the downloader.
●D051 (err)
Message Downloader was stopped due to time-out.
●D052 (err)...

Page 224

7-16
VB-C50FSi/VB-C50FiVideo signal Conforms to NTSC/PALImage Sensor 1/4-inch CCDNumber of pixels NTSC Effective 340,000PAL Effective 400,000
Synchronization InternalScanning Method 2 : 1 interlacedMin. subject illumination Day mode: 1Lux (F1.6, color, NTSC: 1/30 sec PAL: 1/25 sec)Night mode: 0.35Lux (F1.6, monochrome, NTSC: 1/30 sec PAL: 1/25 sec)
Imaging modes Day mode/Night modeFocusingDay mode/Night mode: Auto/Manual Wide-angle: 0.01m(0.03ft) to  /Telephoto: 1.6m(5.25ft) to Night mode (with infrared...

Page 225

7-17
Appendix
Specifications
+3.3V
0.1 µF
10k
Ω 10kΩ 10k
Ω
Internal controllerInput terminals 
IN+, IN–
Output terminals 
OUT A, OUT B, OUT C
+
–
External Device I/O Terminals
You can use Input/Output external devices together with the Multi-Termin\
al Module VB-EX50.
External Device Input Terminals (IN+, IN–)
The external device input terminals consist of 2 terminals (IN+, IN-). The ‘–’ terminal is grounded
on the inside of the main unit. By connecting 2 cables to the + and ‘\
–’ terminals and then...

Page 226

7-18
Note
●Install the Viewer for PC from the “VBToolsInstall.exe” file on th\
e supplied CD-
ROM ( → P.2-13).
● The User’s Manual for the viewer software is provided on the supplied\
 CD-ROM
(Viewer-E.pdf).
● To connect the VB-C50FSi/VB-C50Fi to the Internet, you require a leased \
line connection
to an Internet service provider or a LAN-type dial-up IP connection. If \
you are using a
LAN-type dial-up connection, check that the connection supports bidirect\
ional calling.
System Configuration
This...

Page 227

7-19
Appendix
Sample Network Configurations
This section describes some typical installation modes for the VB-C50FSi\
/VB-C50Fi.
Be sure to assign an IP address to the VB-C50FSi/VB-C50Fi that matches y\
our environment.
This example shows the VB-C50FSi/VB-C50Fi connected to a LAN by Ethernet\
. In this
configuration, videos can be seen by viewers in the same Ethernet segmen\
t as the VB-C50FSi/
VB-C50Fi and by viewers with access to that segment.
Sample Configuration in an ISP Environment
This example...

Page 228

7-20
Upgrading the Firmware Remotely
Note
●Do not turn the power off until you have confirmed that the VB-C50FSi/VB\
-C50Fi
has restarted. Turning the power off before completion may prevent it fr\
om starting
up properly.
● Upgrading the firmware deletes all saved web page data ( → P.5-8). Back up your
data before using this function.
Get the new firmware from Canon Web site, and upgrade in command prompt.\
 The firmware file
is called “Firmware_new.bin” and is saved on your PC in “My Doc\
uments”.
1....

Page 229

7-21
Appendix
Restoring the Factory Default Settings
Since the VB-C50FSi/VB-C50Fi supports a wide variety of functions, we re\
commend that you
make a note of the settings for each function (→ P.7-23).  If you want to redo the settings from the
beginning because you have forgotten them or for some other reason, firs\
t restore the factory
default settings.
* Please refer to page 7-23 for more about the factory default settings.\
Restoring the Factory Default Settings from the Administration Tools Pag\...

Page 230

7-22
Restoring the Factory Default Settings
Note
●Do not turn the VB-C50FSi/VB-C50Fi power off while the Restoring operati\
on.
Turning the power off before completion may prevent it from starting up \
properly.
● If you click the “OK” button at this point, it will not possible t\
o abort the process to
restore the default settings. Click the “Cancel” button if you do \
not wish to restore
the default settings.
● Using “Restore Settings” deletes all saved web page data ( → P.5-8). Back up your
data...
Start reading Canon network camera VBC50Fi User Manual

Related Manuals for Canon network camera VBC50Fi User Manual

All Canon manuals