Canon network camera VBC500D User Manual

1-37
1
1Detailed Settings
Setting User Acces
s Privileges (Access Control) 
Authorized User Account
(1) [User Name], [Password] 
Enter the user name and password and then click [ Add]. The authorized user will be added to 
the user list. 
The user name can consist of up to eight (single-byte ) characters of A to Z, a to z, 0 to 9, - 
(hyphen) and _ (underber). 
The password can consist of up to eight (singl e-byte) ASCII characters (space or printable 
characters).
(2) [User List] A list of authorized...

1-38
Setting User Access Privileges (Access Control)
User Authority 
[Privileged Camera Control], [Camera Control], [Image Distribution], [Audio Distribution] 
Set the user privileges of authorized user s and guest users. Select the check boxes 
corresponding to the items you want to permit for each user. 
Host Access Restriction 
(1) [Host List]
A list of hosts from which access is  permitted and restricted is shown. 
(2) [Apply the list to HTTP Server] If [Ye s ] is selected, the host list is applied...

1-39
Setting User Access Privileges (Access Control)
1
1Detailed Settings
Note
z
If no host list is available, acces s is permitted to all hosts. 
z If a host list is given that indi cates prohibition of all accesses,  the host restriction function is 
disabled and access is permitted to all hosts. 
z To prohibit access via a proxy server in HTTP connection, a proxy server address must 
be set. 
z If Host Access Restriction is set wrongly, access to the setting pages itself may be 
prohibited, in which...

1-40
Setting User Access Privileges (Access Control)
Example of description  Example 1. Prohibit access from a given access 
!172.20.0.10
Access from the host whose address is 172.20.0.10 is prohibited. 
Example 2. Prohibit access from hosts in a given range 
!172.20.0.0-172.20.0.20
Access from the hosts whose address is in a range of 172.20.0.0 to 172.20.0.20 is 
prohibited. 
Example 3. Permit access from hosts in a gi ven range and prohibit access from all other 
hosts 
172.20.0.10-172.20.0.12...

1-41
1
1Detailed Settings
IPsec Settings (IPsec)
IPsec Set
IPsec Sets 1 to 5 are available, where IP
sec settings for each communication using each IPsec 
Set. 
(1) [IPsec]
Select [ Manual] if IPsec will be used. Select [ Disable] if IPsec will not be used. 
(2) [IPsec Mode] Select [ Tunnel Mode ] or [Transport Mode ] as the IPsec operation mode. 
(3) [Destination Address (IPv4/IPv6)]
Enter the IP address of the connection destination.
(4) [Source Address (IPv4/IPv6)] Enter the IP address of the sender....

1-42
IPsec Settings (IPsec)
„If [ ESP] or [ ESP and AH ] was set under [ Security Protocol ] in (5), the following items must be 
set. 
(8) [SA ESP Encryption Algorithm] Select [ AES], [3DES], [DES ] or [ NULL] as the ESP encryption algorithm according to the 
encryption algorithm supported by the device to connect to.
Normally [ AES] or [ 3DES] is recommended.
(9) [SA ESP Authentication Algorithm] Select [ HMAC_SHA1_96], [HMAC_MD5_96] or [ No Authentication]as the ESP authentication 
algorithm according...

1-43
IPsec Settings (IPsec)
1
1Detailed Settings
(14)[SA ESP Authentication key (inbound)]
Set the SA authentication key for inbound. If [
HMAC_SHA1_96] or [HMAC_MD5_96] was 
set in (9), set a 160-bit or 128-bit hexadecimal, respectively. This item need not be set if [ No 
Authentication ] was selected.
(15)[SA ESP SPI (inbound)]
Set the SA SPI value for inbound. Set a desired value in a range of 256 to 4294967295. Since 
this setting is used as an ID for identifying  the SA, be careful not to specify an...

1-44
IPsec Settings (IPsec)
(20)[SA AH SPI (inbound)]
Set the SA SPI value for inbound. Set a desired value in a range of 256 to 4294967295. Since 
this setting is used as an ID for identifying the SA, be careful not to specify an inbound SPI 
whose value is already used the SPI for other AH. 
Note
z To use this camera using IPsec, the communi cating destinations and network must be set 
beforehand. For these settings, contact your System Administrator. 
z If any setting is changed from the [ IPsec]...

1-45
1
1Detailed Settings
Setting the Items Requirin
g Rebooting (Reboot Item) 
(1) [LAN]
IP address and other settings required for LAN Connection (  P. 1-8)
(2) [IPv6] Settings relating to use of IPv6 (  P. 1-9)
(3) [Installation Conditions] Settings relating to camera installation conditions (  P. 1-17)
(4) [MPEG-4] Settings relating to image size and frame rate in MPEG-4 (  P. 1-19)
(5) [HTTP Server] HTTP port number settings (  P. 1-31)
The following items that require rebooting, if changed,...

1-46
Setting the Items Requiring Rebooting (Reboot Item)
Note
These settings relate to network connection. If any setting is changed to a value that may 
disable camera connection from the active browser, the following dialog box is displayed to 
alert the user. 
To apply the new setting, click [ OK]. 
Depending on the new setting, it may not be possible to connect to the camera again after 
rebooting. In this case, a candidate URI is displayed as shown below, 
if available, to facilitate reconnection to...