Canon Maxify Mb5320 User Guide

1.
Enable printer access control(IP address)
Select to enable access control to the printer by IP address.
Note
•
The two types of access control (i.e., by MAC address and by IP address) can be enabled at the same time.
An access control type is enabled as long as the  Enable printer access control check box is
selected, regardless of the type currently displayed by selecting in  Printer Access Control
Type: .
•
When both access control types are enabled at the same time, a computer or a network device...

5.Delete
Deletes the selected IP address from the list.
332
 

Edit Accessible MAC Address Screen/Add Accessible MAC
Address Screen
Note
•
This screen is not available depending on the printer you are using.
The example screenshots in this section refer to the  Add Accessible MAC Address Screen.
1.
MAC Address:
Enter the MAC address of a computer or a network device to allow access.
2.
Comment:
Optionally enter any information to identify the device, such as the name of the computer.
Important
•
Comments will be displayed only on the computer used to enter them.
333
 

Edit Accessible IP Address Screen/Add Accessible IP Address
Screen
Note
•
This screen is not available depending on the printer you are using.
The example screenshots in this section refer to the  Add Accessible IP Address Screen.
1.
Specification Method:
Select either  Single Address Specification  or Range Specification  to add the IP address(es).
Single Address Specification Specify each IP address separately.
Range Specification Specify a range of successive IP addresses.
2.
IP Address:
Enter the IP...

Other Screens of IJ Network Tool
Canon IJ Network Tool Screen
Status Screen
Connection Performance Measurement Screen
Maintenance Screen
Network Setup of the Card Slot Screen
Associate Port Screen
Network Information Screen
335
 

Canon IJ Network Tool ScreenThis section describes the items and menus displayed on the  Canon IJ Network Tool screen.
Items on the Canon IJ Network Tool Screen
Canon IJ Network Tool Menus
Items on the Canon IJ Network Tool ScreenThe following item is displayed on the  Canon IJ Network Tool screen.
1.
Printers:
The printer name, status, printer model name, and port name are displayed.
A check mark next to the printer in the  Name list indicates it is set as the default printer.
Configuration changes are...

Note•
This item has the same function as Refresh in the View menu.
3.
Configuration...
Click to configure settings of the selected printer.
Configuration Screen
Note
•
You cannot configure a printer that has the status  Not Found.
•
This item has the same function as  Configuration... in the Settings  menu.
Canon IJ Network Tool Menus The following menu is displayed from the  Canon IJ Network Tool screen.
1.
File menu
Exit Exits IJ Network Tool.
2.
View  menu
Status Displays the  Status screen to confirm...

•If No Driver  is displayed for the name, associate the port with the printer.
When the Printer Driver Is Not Associated with a Port
•
If Not Found  is displayed for the status, check the followings:
•
The access point is turned on.
•
When using wired LAN, the LAN cable is connected properly.
•
If the printer on a network is not detected, make sure that the printer is turned on, then select
Refresh . It may take several minutes to detect printers. If the printer is not yet detected, connect
the machine...

Maintenance...Displays the  Maintenance  screen to revert the network settings of the printer to factory default
and to mount the card slot as the network drive.
Maintenance Screen
Set up printer's wireless LAN... You can change the access point mode settings. Perform settings following the message on thescreen.
If you change the  Encryption Method:  setting and the Password: setting on the  Set up printer's
wireless LAN  screen, the changed settings are applied to the printer settings.
Note
•...

Status ScreenYou can check the printer status and connection performance.
To display the  Status screen, select  Status from the  View menu.
Note
•
This screen is not available depending on the printer you are using.
•
When using wired LAN,  Signal Strength:, Link Quality:  and Advanced Measurement...  are not
available.
1.
Device Status:
The device status is displayed as  Available or Unavailable .
2.
Signal Strength:
Indicates the strength of the signal received by the printer, ranging from 0% to...