Canon Maxify Mb5020 User Guide

Removing the USB Flash Drive1.
Make sure that the machine is not reading or writing data from/to the USB flash drive.
A message is displayed on the touch screen during such operations.
Important
•
Do not remove the USB flash drive or turn off the power while the machine is reading or writing data from/to it.
Note
•
If your USB flash drive has the access lamp, refer to the instruction manual supplied with the USBflash drive to check if the reading or writing operation is completed on the USB flash drive....

Replacing an Ink Tank
Replacing an Ink Tank
Checking the Ink Status
192
 

Replacing an Ink TankWhen remaining ink cautions or errors occur, the message will appear on the touch screen to inform you ofthe error. Take appropriate action according to the message.
A Message Is Displayed
Note
•
If print results become faint or white streaks appear despite sufficient ink levels, see Maintenance
Procedure .
Replacing Procedure
When you need to replace an ink tank, follow the procedure below.
Important
•
If you remove an ink tank, replace it immediately. Do not leave the machine with...

Caution•
Do not hold the print head holder to stop or move it forcibly. Do not touch the print head holderuntil it stops completely.
Important
•
Do not remove an ink tank until a new one is prepared to be installed.
•
Once you remove an ink tank, the machine will not operate until a new one is installed.
•
Once you remove an ink tank, the machine will not operate even if the removed ink tank isjust reinstalled.
•
You cannot remove the ink tank which is not placed at the replacement position. Removing it...

3.Remove the ink tank from the package.
Important
•
Do not touch the contact (C) and joint (D) of the ink tank.
4.
Insert a new ink tank aligning it with the installation guide (E) of the machine.
195
 

Important•
You cannot insert the ink tank in the wrong position. Check the label under the installation
position, then install the ink tank in the correct position.
5.
Push the ink tank until it snaps firmly into place.
6.
Tap  Exit on the touch screen.
If  Next  is displayed on the screen, it means there is another ink tank that can be replaced.
If you want to replace this ink tank, tap  Next and then repeat procedures from step 2.
To exit the ink tank replacement, tap  Next until  Exit is displayed on...

After replacing the ink tanks, the machine starts mixing the ink automatically. Wait until the machinehas stopped making operating noise. (This takes about 1 to 2 minutes.)
Note
•
If the error message appears on the touch screen, take appropriate action.
A Message Is Displayed
•
If the print head is out of alignment, as indicated by misaligned printed ruled lines or similar
symptoms, 
align the print head .
•
The machine may make noise during operation.
197
 

Checking the Ink Status from Your ComputerYou can check the remaining ink level and the ink tank types for your model.1.
Open the printer driver setup window
2.
Launching the Canon IJ Status Monitor
On the  Maintenance  tab, click View Printer Status .
The Canon IJ Status Monitor opens and displays an image of the ink status.
Note
•
The information displayed on the Canon IJ Status Monitor may differ depending on the country or region where you are using your printer.
3.
If necessary, click  Ink Details...

Checking the Ink Status
Checking the Ink Status with the Touch Screen on the Machine
You can also check the ink status on the computer screen.
Checking the Ink Status from Your Computer
199
 

Checking the Ink Status with the Touch Screen on the Machine1.
Make sure that the power is turned on, and display the HOME screen.
If the HOME screen is not displayed, press the  HOME button to display it.
2.
Tap  on the HOME screen.
Using the Operation Panel
A symbol appears in the area (A) if there is any information about the remaining ink level.
Example: 
Ink tank is running low. Prepare a new ink tank.
Note
•
The above screen shows estimated ink levels.
•
The  Current estimated ink levels  screen...