Canon Lv-7590 Multimedia Projector Users Manual

							81
ON-SCREEN DISPLA yRESOLUTIONH-Freq . 
(kHz) V-Freq .(Hz)
D-VGA 640x480 31.470 59.940 
D-480p 720x480 31.470 59.880 
D-575p 720x575 31.250 50.000 
D-SVGA 800x600 37.879 60.320 
D-XGA 1024x768 43.363 60.000 
D-WXGA 1 1366x768 48.360 60.000 
D-WXGA 2 1360x768 47.700 60.000 
D-WXGA 3 1376x768 48.360 60.000 
D-WXGA 4 1360x768 56.160 72.000 
D-WXGA 5 1366x768 46.500 50.000 
D-WXGA 6 1280x768 47.776 59.870 
D-WXGA 7 1280x768 60.289 74.893 
D-WXGA 9 1280x800 49.600 60.050 
D-WXGA 10 1280x800 41.200 50.000 ON-SCREEN 
DISPLA yRESOLUTIONH-Freq . 
(kHz) V-Freq .(Hz)
D-WXGA 11 1280x800 49.70259.810
D-SXGA 2 1280x1024 60.27658.069
D-SXGA 3 1280x1024 31.65029.800
D-WXGA+ 1 1440x900 55.93559.887
D-720p 1280x720 45.000 60.000 
D-720p 1280x720 37.500 50.000 
D-1035i
1920x1035 (Interlace)33.750 60.000
D-1080i
1920x1080 (Interlace)33.750 60.000
1920x1080
(Interlace)28.125 50.000
D-1080psf/30 1920x1080 33.750 60.000 
D-1080psf/25 1920x1080 28.125 50.000 
D-1080psf/24 1920x1080 27.000 48.000 
Appendix
✔Note:
	 •	Depending	on	the	condition	of	signals	and	the	type	and	length	of	cables,	these	signals	may	not	be	properly	
viewed.
	 •	Specifications	are	subject	to	change	without	notice.
When an input signal is digital from the DVI terminal, refer to the chart below. 
						

							82
Technical Specifications
Mechanical Information 
 Projector Type  Multi-media Projector 
  Dimensions (W x H x D)  14.56” x 7.36” x 17.32” (370.0 mm x 187.0 mm x 439.9 mm) 
  Net Weight  25.1 lbs (11.4 kg) 
  Feet Adjustment  0˚ to 6.5˚           
 
Panel Resolution 
 LCD Panel System  1.3” TFT Active Matrix type, 3 panels  
  Panel Resolution  1,024 x 768 dots 
  Number of Pixels  2,359,296 (1,024 x 768 x 3 panels)           
 
Signal Compatibility 
 Color System PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N 
  High Definition TV Signal  480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
 
 Input Scanning Frequency  H-sync. 15 kHz–100 kHz, V-sync. 48 Hz–100 Hz      
 
Optical Information 
　Projection Lens  Optional 
　Projection Lamp  330 W NSHA lamp 
 
Interface
 Input 1  Digital (DVI-D) x 1, Analog (Mini D-sub 15 pin) x 1 
  Input 2  BNC Type x 5 (G or Video/Y, B or Cb-Pb, R or Cr-Pr, HV and V) 
  Input 3  RCA Type x 3 (Video/Component), Mini DIN 4 pin x 1 (S-video) 
 Monitor Out Analog RGB (Mini D-sub 15 pin) Terminal x 1 
 Audio Out  Audio (Mini Type stereo) x 1 
 Audio In I/ II Audio (Mini Type stereo) x 2 
  R/C Jack  Mini jack (Wired Remote) x 1 
  Control Port  D-sub 9 pin x 1  
  USB Connector   USB Series B x 1 
  Option  Network Imager Terminal x 1 
 
Power
 Voltage and Power Consumption  AC 100–120 V (5.5 A Max. Ampere), 50/60 Hz (The U.S.A and Canada) 
    AC 200–240 V (2.6 A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)   
 
Operating Environment
 Operating Temperature  41˚F–104˚F (5˚C–40˚C) 
  Storage Temperature  14˚F–140˚F (-10˚C–60˚C) 
 
Remote Control Unit 
  Battery  AAA or LR03 Type x 2           
  Operating Range  16.4’ (5 m/±30˚) 
  Dimensions  1.8” (W) x 1.0” (H) x 5.7” (D) (45 mm x 25 mm x 145 mm)       
  Net Weight  3.5 oz (99 g) (including batteries) 
 
Accessories
 User’s Manual (CD-ROM)  Lens Attachment, Screws (W3), (W4)
  Quick Start Guide  Light-block sheet (G), (H) 
  AC Power Cord  Spacers (For optional lens) 
  Remote Control Unit and Batteries　  Warranty card 
  VGA Cable (1AV4W20B29700)    
  USB Cable (1AV4W20B20201) 
  PIN Code Label 
Appendix
●  The specifications are subject to change without notice.
●  LCD panels are manufactured to the highest possible standards. Even though 
99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less) 
may be ineffective by the characteristics of the LCD panels. 
						

							83
Optional Parts
Lens Replacement
The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector 
for wide variety of uses. 
For installation and replacement of the lens, always contact the sales dealer. The projector lens must be 
installed or replaced by well-trained sales or service engineers. Do not attempt to install and replace the lens by 
yourself as it may cause injury.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the projector. 
This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information 
System Industries Association). The projector supports all commands defined by PJLink Class 1 and is verified 
conformance with PJLink Standard Class 1.
PJLink is a registered trademark of JBMIA and pending trademark in some \
countries.
PJ Link Notice
To the sales and service engineers:
For the lens replacement and lens installation, refer to the installation manual of the optional lens. Before replacing and 
installing the lens, make sure that you are using the lens with the correct Type No.
Projector InputPJLink InputParameter
Input 1 RGB (PC analog) RGB 111
RGB (Scart) RGB 212
RGB (PC digital) DIGITAL 131
RGB (AV HDCP) DIGITAL 232
Input 2 Video VIDEO 121
Y, Pb/Cb,Pr/Cr VIDEO 222
RGB RGB 313
Input 3 Video VIDEO 323
Y, Pb/Cb,Pr/Cr VIDEO 424
S-video VIDEO 525
Input 4 Network NETWORK 151
      Model No.
Ultra Wide Angle Lens     Type No. : LV-IL01 
Wide Angle Zoom Lens     Type No. : LV-IL02 
Long Focus Zoom Lens     Type No. : LV-IL03 
Ultra Long Focus Zoom Lens     Type No. : LV-IL04
Standard Zoom Lens    Type No. :  LV-IL05 
Ceiling Attachment    Type No. : LV-CL13 
High Ceiling Attachment     Type No. : LV-CL14 
Network Imager    Type No. : LV-NI03
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No. 
to the sales dealer.
Appendix 
						

							84
Configurations of Terminals
INPUT 1 (ANALOG)/ MONITOR OUT (Mini D-sub 15 pin)
512341096781514131 112
CONTROL TERMINAL (D-sub 9 pin)
-----
R X D
T X D
-----
SG
-----
RTS
CTS
Serial
1
2
3
4
5
6
7
8
INPUT 1 (DIGITAL) (DVI 24 PIN)
1917
21018
31 119
41220
51321
61422
71523
81624
T.M.D.S. Data2–
No Connect
T.M.D.S. Data2+
No Connect
T.M.D.S. Data2 Shield
DDC Clock
DDC Data
No Connect
1
5
2
4
3
6
7
8
T.M.D.S. Data1–
No Connect
T.M.D.S. Data1+
No Connect
T.M.D.S. Data1 Shield
+5V Power
Ground (for +5V)
Hot Plug Detect
9
13
10
12
11
14
15
16
T.M.D.S. Data0–
No Connect
T.M.D.S. Data0+
No Connect
T.M.D.S. Data0 Shield
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
17
21
18
20
19
22
23
24
Vcc
- Data
+ Data
Ground
1
2
3
4
USB TERMINAL (Series B)
2
34 1
Appendix
-----9
Red Input
Ground (Horiz.sync.)
Green Input
No Connect
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
Horiz. sync. Input (Composite H/V sync.)
Ground (Vert.sync.)
 DDC Data
Ground
Vert. sync. Input
 DDC Clock
9
13
10
12
11
14
15
+5V Power
Red Output
Ground (Horiz.sync.)
Green Output
No Connect
Blue Output
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
Horiz. sync. Output 
Ground (Vert.sync.)
No Connect
No Connect
Vert. sync. Output
No Connect
9
13
10
12
11
14
15
No Connect
Input
Output 
						

							85
Put the label below (supplied) on in a prominent place of 
the projector’s body while it is locked with a PIN code. While the projector is locked with the PIN code...
Appendix 
						

							86
Dimensions
3.94 (100)
14.57 (370)
5.75 (146)
17.32 (439.9)13.58 (345)
4.13 (105)
5.20 (132) 4.33 (110)
4.33 (110)
7.36 (187)
6.5º MAX
Screw Holes for Ceiling Mount
Screw: M6
Depth: 0.393 (10.0)
2.05 (52)
Unit: inch (mm)
Appendix 
						

							87
Serial Control Interface
Appendix
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial 
port.
Connect a RS-232C serial cross cable to CONTROL 
PORT on the projector and serial port on the PC.
 (See p.24)
Launch a communication software provided with PC 
and setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bps
Parity check  : none
Stop bit   : 1
Flow control  : none
Data bit   : 8
Type the command for controlling the projector and 
then enter the "Enter" key. 
Example
When you want to change the input to INPUT 2, Type 
'C' '0' '6' 'Enter'. 
✔Note:
	 •	 Enter	with	 ASCII	64-byte	capital	characters	and	one-
byte	characters.
✔Note:
	 •	The	default	of	the	baud	rate	is	set	to	19200	bps.	If	an	 error	occurs	in	the	communication,	change	the	serial	
port	and	the	communication	speed	(baud	rate).
Operation 
						

							88
The command is sent from PC to the projector with 
the format below;
     'C' [Command] 'CR'
        Command: two characters (refer to the 
command table below.
-The projector decodes the command and returns the 
'ACK' with the format below;
      'ACK'  'CR'
-When the projector can not decode the command, it 
returns with format below.
      ‘?’  ‘CR’ 
Format
Appendix
Functional Execution Command
Command
Function
C00 Turn the projector ON
C01 Turn the projector OFF 
(immediately OFF)
C02 Turn the projector OFF
C05 Select Input 1
C06 Select Input 2
C07 Select Input 3
C08 Select Network
C09 Volume +
C0A Volume -
C0B Sound mute ON
C0C Sound mute OFF
C0D Video mute ON
C0E Video mute OFF
C0F Aspect 4:3
C10 Aspect 16:9
C1C Menu ON
C1D Menu OFF
C20 Brightness UP
C21 Brightness DOWN
C23 Select Input 2 Video
C24 Select Input 2 Y, Pb/Cb,Pr/Cr 
C25 Select Input 2 RGB
C28 ON Start ON
C29 ON Start OFF
C33 Select Input 3 Video
C34 Select Input 3 S-video
C35 Select Input 3 Y, Pb/Cb,Pr/Cr Command Function
C3A Pointer RIGHT
C3B Pointer LEFT
C3C Pointer UP
C3D Pointer DOWN
C3F Enter
C46 Zoom DOWN
C47 Zoom UP
C4A Focus DOWN
C4B Focus UP
C50 Select Input 1 Analog RGB
C51 Select Input 1 SCART
C52 Select Input 1 DVI (PC Digital)
C53 Select Input 1 DVI (AV HDCP)
C5D Lens shift UP
C5E Lens shift DOWN
C5F Lens shift LEFT
C60 Lens shift RIGHT
C89 Auto PC Adj.
C8E Keystone UP
C8F Keystone DOWN
C90 Keystone RIGHT
C91 Keystone LEFT 
						

							89
Status Read Command
Appendix
The command is sent from PC to the projector with 
the format below;
     'CR' [Command] 'CR'
        Command: one character (refer to the command 
table below.
The projector decodes the command and returns the 
'Character string' with the format below; Format
The tables on page 88 and 89 show the typical command lists for controlling the projector.  Please consult your 
local dealer for further information of other commands.
Command FunctionProjector 
Return Projector status
CR0
Status Read 00
Power On
80 Stand-by mode
40 Countdown
20 Cooling down
10 Power Malfunction
28 Cooling down at the temperature abnormally
24 Cooling down at Power Management mode
04 Power Management mode after Cooling down
21 Cooling down after the projector is turned off when the lamps 
are out.
81 Stand-by mode after Cooling down when the lamps are out.
88 Stand-by mode after Cooling down at the temperature 
abnormally.
2C Cooling down when the projector is turned off by the shutter 
management function.
8C Stand-by mode after cooling down by the shutter management 
function. 
CR6 Temperature Read S1 S2 S3S1 = Temperature at Sensor 1 (˚C)
S2 = Temperature at Sensor 2 (˚C)
S3 = Temperature at Sensor 3 (˚C)
(ex.) S1 = 12.3˚C,  S2 = 23.4˚C, S3 = 34.5˚C
 --> The projector displays “12.3 23.4 34.5”
    ( 
For each sensor, two digit and the tenth place numbers are 
displayed with a space between each temperature.)
? Communication failure 
						

							© CANON INC. 2010
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501,
 Japan
CANON U.S.A. INC.
One Canon Plaza, Lake Success, NY 11042-1198, 
U.S.A.
CANON CANADA INC. HEADQUARTERS
6390 Dixie Road, Mississauga, Ontario L5T 1P7,
Canada
CANON CANADA INC. MONTREAL BRANCH
5990, Côte-de-Liesse, Montréal Québec H4T 1V7, 
Canada
CANON CANADA INC. CALGARY OFFICE
2828, 16th Street, N.E. Calgar y, Alberta T2E 7K7, 
Canada
CANON EUROPE LTD.
3 The Square, Stockley Park, Uxbridge, Middlesex, UB11 
1ET United Kingdom
CANON EUROPA N.V.
Bovenkerkerweg 59-61, 1185 XB Amstelveen, 
The Netherlands
CANON FRANCE S.A.S
17, quai du President Paul Doumer, 92414 Courbevoie 
Cedex, France
CANON UK LTD.
Woodhatch Reigate Surrey RH2 8BF, United Kingdom
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A10, 47807 Krefeld, Germany
CANON ITALIA S.p.A.
Via Milano 8 I-20097 San Donato Milanese, Milano, 
Italy
CANON Schweiz AG
Geschäftsbereich Wieder verkauf, Industriestrasse 12, 
CH-8305 Dietlikon, Switzerland
CANON GMBH
Zetschegasse 11, A-1230 Wien, Austria
CANON España, S.A.
C/Joaquín Costa, 41, 28002 Madrid, SpainCANON PORTUGAL S.A.
Rua Alfredo da Silva, 14 Alfragide 2610-016 Amadora,
 Portugal
CANON Belgium N.V./S.A.
Berkenlaan 3, 1831 Diegem (Mechelen), Belgium
CANON Netherland NV
Neptunusstraat 1, 2132 JA Hoofddorp, 
The Netherlands
CANON LUXEMBOURG S.A.
Rue des Joncs 21, L1-818 Howald, Luxembourg
CANON DANMARK A/S
Knud Hoejgaards Vej 1 DK-2860 Soeborg,
Danmark
CANON OY
Huopalahdentie 24 PL 1 00351 Helsinki, Finland
CANON SVENSKA AB
Gustav III:s Boulevard 26 169 88 Solna, Sweden
CANON NORGE as
Hallagerbakken 110, Postboks 33, Holmlia, 1201
Oslo, Norway
CANON LATIN AMERICA, INC.
703 Waterford Way, Ste. 400 Miami, FL 33126,
U.S.A.
CANON (China) Co., Ltd.
15F Jinbao Building No.89 Jinbao Street, 
Dongcheng District, Beijing 100005, China
CANON HONGKONG CO., LTD.
19/F., The Metropolis Tower, 10 Metropolis Drive,
Hunghom, Kowloon, Hong Kong
CANON SINGAPORE PTE. LTD.
1 HarbourFront Avenue, #04-01 Keppel Bay
Tower, Singapore 098632
CANON KOREA CONSUMER IMAGING INC.
Gangnam Finance Center 17F, 737, Yeoksam-
Dong, Gangnam-gu, Seoul, 135-984, Korea
CANON AUSTRALIA PTY. LTD.
1 Thomas Holt Drive, North Ryde, N.S.W. 2113,
Australia
CANON NEW ZEALAND LTD.
Akoranga Business Park, Akoranga Drive, Northcote, 
Auckland, New Zealand
KR7PL