Canon large format printer imagePROGRAF iPF6400 User Manual

Support Sheet
Support Sheet
You can display product support information and the electronic manual.
•
Support Information
 button
Click the button to display websites that contain the latest product information.
Note
•An Internet connection is needed to view the websites.•
User Manual button
Click the button to display the printer manuals installed on the computer.
Note
•You must have User Manual installed on your computer.
Adjustment pattern setting dialog box
Adjustment pattern setting dialog box...

The adjustment values of the image enclosed in the blue frame in the center are used as the base values, with
images arranged around this with the adjustment values varying in steps up and down from these base values. If
you click any of the images, the adjustment pattern is redisplayed with the adjustment values from that image as
the base values.
The adjustment values are displayed at the top of each image. If both the  Horizontal Axis and Vertical Axis  are
configured, the adjustment value for the...

You can select the interval of the variation in adjustment values between neighboring adjustment pattern im-
ages from the range of 1 to 10. The larger the value, the greater the differences between the states of the
adjustment pattern images. Note that if the adjustment item is  Tone, the Adjustment Value Spacing  cannot
be selected.•
(Swap) button
Rearranges the adjustment pattern with the  Horizontal Axis and Vertical Axis  adjustment items swapped.
•
Rotate 90 degrees
Rotating the image may make it...

•
Specify the Range of Images button
When this button is clicked, the  Specify the Range of Images dialog box is displayed for specifying the range of
images.
When you specify the range by using the mouse or other means and then click the  OK button, the  Specify the
Range of Images  dialog box closes and the specified image range is redisplayed as the adjustment pattern.
If you click the  Cancel button, the  Specify the Range of Images  dialog box closes even if a range is selected.
Note
•The selected...

Note
•The job name when printing the adjustment pattern is "Original Image Name + Pattern-Print". For example, the print jobname for the image "ABC.jpg" is "ABC_Pattern-Print.jpg".
Paper Detailed Settings Dialog Box
Paper Detailed Settings Dialog Box
This dialog box appears when you click the 
Advanced Settings button on the Main Sheet. You can set  Drying Time
and  Roll Paper Margin for Safety  by media type.
•
Drying Time
Between Pages
This sets the wait time for the ink to dry...

SettingDetailsPrinter DefaultThe settings of the printer operating panel are applied.FastSelect this setting if cutting with the Standard setting is not clean.StandardSelect this setting when you are not experiencing problems.SlowThis helps prevent adhesive from sticking to the cutter and keeps the cutter sharp if you select itwhen using adhesive paper.•
Calibration Value
When calibration has been carried out on the printer, use this setting to choose whether or not to use the results....

The following settings are available for the image enlargement method.SettingDetailsNearest NeighborPerforms simple enlargement.BilinearPerforms line vector enlargement.BicubicAdjust pixels with calculation of elements such as a color or brightness of neighboring pixels.•
Close Plug-in After Printing
When you place a checkmark here, the plug-in closes after printing finishes.
Note
•If printing does not finish correctly because it was canceled or an error occurred, the plug-in does not close.•
Initialize...

SettingDetailsSimulate Black InkSelect this when performing simulation of black ink. In order to enable this setting, Adobe CMMneeds to be selected under Conversion Engine.
Roll Paper Options Dialog Box
Roll Paper Options Dialog Box
This dialog box appears when you click the 
Roll Paper Options button on the Page Setup Sheet. You can set the roll
paper width and perform the auto cut settings.
•
Roll Paper Width
This selects the width of the roll media set to the printer.  
•
Automatic Cutting
You can set...

•
Units
You can select the units of measure to use when you define custom media size. Switching this setting resets theunits of measure for the entire Plug-In.
 
•
Paper Size
Width
Enter the width of the media size.
 
Height
Enter the height of the media size.
•
Add  button
Click the button to register the contents of the settings.
 
Curves Dialog Box
Curves Dialog Box
This dialog box appears when you click the 
Curves button on the  Color Settings  Sheet. You can set  Channel and
other settings.
•...

Note
•The allowed entry range is 0 to 255.•You can change the numbers by clicking either ▲ button or ▼ button.•
Load Curves button
Click the button to load stored data for a tone curve.
 
•
Save Curves  button
Click the button to stores the current tone curve settings.
 
Print History Details Dialog Box
Print History Details Dialog Box
This dialog box appears when you click the 
Details button on the  Print History Sheet. This controls print history. For
more information about  Print History Details, see...