Canon Ir Advance C5051 User Guide

							1
Placing Originals2-29
2
Making Copies in the Voice Navigation Mode
•If the size of the original is not detected, 
press  (Start)  follow the 
instructions on the screen to specify the 
original size. You can also manually 
select the paper size.
•For more information, see Paper 
Selection, on p. 2-37.
 
						

							Making Copies in the Voice Navigation Mode
1
2
Placing Originals
2-30
Feeder
You should use the feeder when you want to 
copy several originals at the same time. Place 
your originals into the feeder, and then press 
 (Start). The machine automatically feeds 
the originals to the platen glass and scans 
them. 2-sided originals can also be 
automatically turned over and scanned as 2 
or 1-sided documents.
You can place the following originals into the 
feeders original supply tray:
• Weight:
- One-sided scanning: 11 to 32 lb bond (42 to 128 g/m
2)
- Two-sided scanning: 13 to 32 lb bond (50 to 128 g/m
2)
• Size:
- 11 x 17, LGL, LTR, LTRR, STMT, or  STMTR/A3, B4, A4, A4R, B5, B5R, A5, 
A5R, or B6R
• Tray Capacity:
- 150 sheets of paper (20 lb bond (80g/m
2))
 
						

							1
Placing Originals2-31
2
Making Copies in the Voice Navigation Mode
These specifications may vary, depending on 
the machine you are using. For exact 
speci fications, please see the instruction 
manuals that came with your machine.
IMPORTANT
•Thin originals may become creased, if 
used in a high temperature or high humidity 
environment.
•Do not place the following types of originals 
into the feeder:
- Originals with tears or large binding holes
- Severely curled originals or originals with  sharp folds
- Clipped or stapled originals
- Carbon backed paper or other originals  which may not feed smoothly
- Transparencies and other highly  transparent originals
•If the same original is fed through the 
feeder repeatedly, the original may fold or 
become creased, and make feeding 
impossible. Limit repeated feeding to a 
maximum of 30 times (this number varies, 
depending on the type and quality of the 
original).
 
						

							Making Copies in the Voice Navigation Mode
1
2
Placing Originals
2-32 •
If the feeder rollers are dir ty from scanning 
originals written in pencil, perform the 
feeder cleaning procedure. (See the 
instruction manuals that came with your 
machine.) The feeder cleaning procedure is 
not supported by the Voice Navigation 
mode. Please seek assistance if it 
becomes necessary to perform this 
procedure.
•Always smooth out any folds in your 
originals before placing them into the 
feeder.
1Adjust the slide guides to  fit the size 
of your originals.
 
						

							1
Placing Originals2-33
2
Making Copies in the Voice Navigation Mode
2Neatly place your originals with the 
side to be copied face up into the 
original supply tray.
Place your originals as far into the 
feeder as they will go, until the Original 
Set indicator is lit.
If any dirt on the original scanning area 
is detected when the originals are 
placed in the feeder, the following 
screen appears. Even though streaks 
may appear on the copies, you can 
continue to scan your documents by 
pressing  (Select).
Original Set Indicator
 
						

							Making Copies in the Voice Navigation Mode
1
2
Placing Originals
2-34 It is recommended, however, that you 
open the feeder, clean the scanning 
area (thin glass strip on the platen glass’ 
left side with a slightly dampened, well 
wrung-out cloth), and then close the 
feeder. The following screen depicting 
how to clean the thin glass strip will not 
appear once the scanning area is clean.
For instructions on cleaning the original 
scanning area, see the instruction 
manuals that came with your machine.
 
						

							1
Placing Originals2-35
2
Making Copies in the Voice Navigation Mode
This procedure must be performed 
manually, and therefore, there are no 
voice navigation instructions. Please 
seek assistance if you must perform this 
procedure.
IMPORTANT
•Do not add or remove originals while 
they are being scanned.
•When scanning is complete, remove the 
originals from the original output area to 
avoid paper jams.
Original Output Area
 
						

							Making Copies in the Voice Navigation Mode
1
2
Placing Originals
2-36
NOTE
•The scanned originals are output to the 
original output area in the order that they 
are fed into the feeder.
•When you are enlarging an LTR or 
STMT/A4 or B5 original onto 11 x 17 or 
LGL/A3 or B4 paper, place the original 
horizontally.
•You can place different size originals 
together into the feeder if you set the 
Different Size Originals mode. (See the 
instruction manuals that came with your 
machine.) The Different Size Originals 
mode is not suppor ted by the Voice 
Navigation mode. Please seek 
assistance if you need to use this mode.
 
						

							2
Making Copies in the Voice Navigation Mode
Basic Copy Settings2-37
Basic Copy Settings
This section explains the procedure for 
specifying basic copy settings, such as 
selecting the paper size, and setting the 
Original Type, Select Color, Density, Copy 
Ratio, 2-Sided, and Finishing modes.
Paper Selection
You can manually specify a paper size or set 
the machine to automatically select a paper 
size for you.
IMPORTANT
You cannot specify the multi-purpose tray or 
select [Change MP Tray Paper] while in the 
Voice Navigation mode.
NOTE
The default setting is Auto.
 
						

							Making Copies in the Voice Navigation Mode
1
2
Basic Copy Settings
2-38
1Place your originals.
IMPORTANT
Only the paper size and paper type can 
be selected from the Select Paper setting 
screen in the Voice Navigation mode. If 
you want to set a paper source to hold a 
speci fic paper size and type, you must 
change the paper loaded in the paper 
drawer and the size, and then set the type 
in [Paper Settings] in Settings/
Registration. For more information on 
changing the paper and paper type, see 
the instruction manuals that came with 
your machine.