Canon Imageprograf Ipf815 Mfp M40 User Guide

Setting Item
Description, Instructions(The type of paper is dis-
played here.)
(*1
→P.726
) Feed Priority
Specify exact paper feeding, if desired. Normally, select
Automatic. Choose Print Length if you prefer to feed the
paper an exact amount. However, note that choosing  Print
Length may result in slight banding in the direction of
Carriage scanning.
Adjust Length Displayed if Feed Priority is Print Length.
Adjustment relative to the amount of stretching or shrink-
age of the current paper.
Enter either...

Setting Item
Description, Instructions(The type of paper is dis-
played here.)
(*1
→P.726
) Bordless Margin
Choose Automatic to have the printer automatically de-
tect the paper width and configure the margin settings for
borderless printing. If margins are mistakenly created
when Automatic is selected, choose  Fixed. In this case,
the paper width is not detected automatically, and the
document is printed without borders, using the margin set-
tings required by the printer.
CutDustReduct. If you choose...

Setting Item
Description, InstructionsJob
Log (Choo
se
from
infor-
ma-
tion
about
the
latest
three
print
jobs.)
Document Name
Displays the document name in the last print job.
User Name Displays the name of the user who sent the print job.
Page Count Displays the number of pages in the print job.
Job Status Displays the results of the print job processed.
Print Start Time Displays the time when the print job was started.
Print End Time Displays the time when the print job was finished.
Print Time...

Setting Item
Description, InstructionsPaper Manag-
er
Margin
Specify the margin around paper. The margin for the trailing
edge of sheets is 23 mm (0.9 in).
However, if you have specified the leading margin in  Paper
Details, the value in  Paper Details has priority.
Conserve Paper Conserves paper when printing.
Auto Rotate If the long side of an original is shorter than the roll width,
the original is automatically rotated 90 degrees to conserve
paper. Similarly, if the long side of an original in...

Setting Item
Description, InstructionsLine & Pen
Manager
Smoothing
•If you choose Software
Operation  is  determined  by  the  application.  If  nothing  is
specified  by  the  application,  the  result  is  as  shown  in  the
figure. Note: By default, this is a 72-sided figure
• If you choose Smooth ThickenFineLines
Select On to print fine lines more distinctly.
AdjustFaintLines If fine lines are printed in colors that do not match the colors
of other shapes, selecting  Off may help produce the...

Setting Item
Description, InstructionsAuto Head Adj.
Advanced Adj.Choose Yes to have the printer print and read a test pattern
for the automatic adjustment of Printhead alignment rela-
tive to the nozzle, ink tank, and printing direction.   (See
"Automatic Straightening of Lines and Colors (Auto
Head Adj.) .") →P.668
Auto Print Choose On to have the printer automatically execute the
Advanced Adj. operations after you replace the Print-
head.  (See "Automatic Straightening of Lines and Col-...

Setting Item
Description, InstructionsTCP/IP
IP Setting IP Address Specify the printer network information when using a static
IP address.
Enter the IP address assigned to the printer, as well as the
network subnet mask and default gateway.
Subnet Mask
Default G/W NetWare NetWare
Specify the NetWare protocol. To apply your changes,
choose Register Setting.
Frame Type Specify the frame type to use.
Print Service Choose the print service.
AppleTalk Specify whether to use the AppleTalk protocol. To apply...

System Setup
Setting Item
Description, InstructionsWarning
BuzzerSet the buzzer. Choose On for the buzzer to sound once
for warnings and three times for errors.
Detect Mismatch Choose Warning for notification (display of a warning
message) during printing if the paper type specified in the
printer menu does not match the paper type in the printer
driver. Choose None to continue to print without notifica-
tion. Choose Pause to have printing paused under these
circumstances. In this case, you can continue...

Setting Item
Description, Instructions
TrimEdge Reload Specify whether to trim the leading edge of the currently
retracted roll when the roll is advanced. Cut the edge if
you are concerned about any marks left on the roll when
the roll is left in the retracted position. Selecting  On will
always trim the edge when the roll is advanced from the
retracted position. Selecting  Automatic will trim the edge
when the roll has been in the retracted position for two
days or more.
Noz. Check Freq. Specify the...

Setting Item
Description, InstructionsOutput Method
Save: Box 01 Select the output method.
To print as usual, select 
Print. Selecting Print (Auto Del)
will print the job and then delete the data from the printer's
hard disk. Selecting  Save: Box 01 will only save the print
job in the box, without printing it.
Save and Print Select On to print the job after it has been saved.
Save: Shared Box Select Off to print without saving jobs in the box shared
among multiple users.
Show Job Log Selecting Off...