Canon I Sensys Mf8230cn User Guide

Connect the modular  handset  cable to the handset  jack.
Attach  the four handset  cable clamps.
Run the handset  cable through the clamps  and  close  them.
Continue  to Connecting the Power Cord
6
7
8
»
>ß>Ý>Ì>Û>Ì>â>ã>â
 

0ALJ-00E
Connecting the Power Cord
Connect  the  power cord  to  the  machine. Read the  precautions in Power  Supplybefore connecting the  power cord.
NOTE
Do not  connect the  USB  cable yet.  Wait until you install the  software  to  connect the  USB  cable.
Make sure that  the machine is  turned OFF.
Plug the female end  of the power cord into the power socket  on the back of the machine.
Plug the male  end  of the power cord into an AC power outlet.
Continue  to Turning  ON  the Power and...

0ALJ-00F
Turning ON the Power and Configuring Initial Settings
Turn  ON the  machine, and  follow  the  on -screen instructions to  configure the  initial settings.
Turn ON the machine.
Use  /  to select the display language, and  press  .
Use  /  to select your country  or region, and  press  .
Read the reminder messages that  are displayed,  and  press   to continue.
NOTE:
If  the   message is  shown on  the  display,  remove  the  packing  materials
under the  rear cover. 
Removing Packing Materials...

Use  /  to select whether or not to perform color  correction,  and  press  .
When  color correction  is  performed, you can make copies and  prints  that  more closely  reproduce the  colors and  density  of the
original  document. The time  it takes  to  apply  color correction  is  approximately  2  to  4  minutes.  Color correction  can be performed
later.
Performing color  correction
1Check that the size and  type  of paper displayed on  the screen  is  loaded in the machine, and  press .
2Confirm...

Confirm  that  one of the screens shown here is  displayed.
If you want to connect the machine to a computer,  continue  to Connecting to a  Computer
If you do not want to connect the machine to a computer  and  are using MF8540Cdn  / MF8230Cn, the initial
settings  are complete.  If you are using MF8580Cdw / MF8550Cdn  / MF8280Cw,  use  /  to select 
and  press  ,  and  then proceed to 
Configuring Initial Settings for  Fax Functions (MF8580Cdw /  MF8550Cdn /
MF8280Cw Only)
the  machine?
Has a paper...

0ALJ-00H
Connecting to a Computer
When  connecting the  machine to  a computer, you can select whether  to  connect via  wireless LAN, wired LAN, or USB.  Select the
connection method that  best suits your environment and  devices.
A LAN cable is  not  required because  wireless communications  (radio waves) are
used to  connect the  machine and  the  router.
If  you want to  connect the  machine to  a computer  via  wireless LAN now, use 
/ to  select , and  press , and  then  proceed toConnecting via...

If  the  screen shown below is  displayed,  proceed to  Connecting via USB.
NOTE
The machine does not  come  with a LAN cable or router. Have  them ready as necessary.
If  you are  not  sure  whether  the  router  you are  using supports wireless LAN or wired LAN, see  the  instruction  manual  provided
with the  router, or contact your manufacturer.
The operating  systems listed below are  compatible  with the  included  software, such as the  drivers, which are  used for
connecting the  machine to  a...

0ALJ-00J
Connecting via Wireless LAN (MF8580Cdw / MF8280Cw Only)
The machine and  computer  are  connected via  a wireless LAN router. A LAN cable is  not  required because  wireless communications  (radio
waves) are  used to  connect the  machine and  the  router.
NOTE
The machine does not  come  with a wireless LAN router. Have  it ready as necessary.
The wireless router  must conform to  IEEE  802.11b/g/n  and  be able  to  communicate in 2.4  GHz bandwidth. For more
information, see  the  instruction...

Install  the software.
Install the  MF Drivers, MF Toolbox, and  the  other included  software. For more information, see  MF Driver  Installation Guide.
After installing the software, continue  to Configuring Initial Settings for  Fax Functions (MF8580Cdw /  MF8550Cdn /
MF8280Cw Only)
NOTE:
If the Remote  UI screen  is  not  displayed
Make  sure  that  the  machine is  properly  connected to  the  computer  via  a wireless LAN. 
Installation/Settings
Problems
5
»
>ß>å>Ì>Û>Ì>â>ã>â
 

0ALJ-00K
Connecting via Wired LAN
The machine and  computer  are  connected via  a wired LAN router. Use  a LAN cable to  connect the  machine to  the  router.
NOTE
The machine does not  come  with a LAN cable or router. Have  them ready as necessary. Use  a Category 5  or higher twisted
pair  cable for  the  LAN.
Make  sure  that  there are  ports available on  the  router  to  connect the  machine and  the  computer.
The machine supports 10BASE-T  and  100BASE-TX connections. If  you want to  connect...