Canon I Sensys Mf8230cn User Guide

If your  wireless router is  not  found
Check whether  the  machine is  properly  installed and  ready to  connect to  the  network. 
Installation/Settings Problems
Enter  the network key that  you have written down.
Enter the  network key  using the  numeric keys, and  press .Entering Text
WEP
WPA - PSK or WPA2- PSK
Select ,  and  press  .
NOTE:
If an error message  is  displayed during setup
Press 
, check  whether  the  network key  is  correct,  and  return to  step 5.
Check  that  the Wi-Fi...

LINKS
Connecting to a Wireless LAN (MF8580Cdw  / MF8280Cw Only)
>ß>ß>Þ>Ì>Û>Ì>â>ã>â
 

0ALJ-081
Setting Up Connection by Specifying Detailed Settings
If  you want to  specify  the  security settings in detail or cannot  establish the  wireless connection using the  other procedures,  manually
enter all the  required information  for  the  wireless LAN connection.  Before specifying  detailed settings,  check  and  write down the  required
information, including the  SSID, network key, and  wireless security protocols (
Checking the SSID and  Network Key).
Press  .
Use  /  to select ,  and...

Using  WPA-PSK  or WPA2-PSK
Select ,  and  press  .
4Select the WEP  key(1  to 4)  you want to edit, and  press .
Up to  four  WEP keys can be registered.
5Enter  the network key that you have  written down. Enter the  network key  using the  numeric keys, and  press . 
Entering Text
6Select ,  and  press .
7Select the WEP  key you have  edited, and  press .
1Select , and  press .
2Select an encryption  method,  and  press .

Sets the  machine to  automatically select AES-CCMP or TKIP  to  match the...

NOTE:
If an error message  is  displayed during setup
Press 
, check  whether  the  specified settings are  correct,  and  return to  step 5.
Check  that  the Wi-Fi indicator is  blinking  on the operation panel.
The Wi-Fi  indicator blinks when a wireless router  is  detected.
When  the  setup is  completed, the  screen below is  displayed,  and  approximately  2  seconds  later, the  Wi-Fi  indicator lights up.
Wait approximately  2  minutes  until the  IP  address settings of the  machine are...

0ALJ-082
Checking the SSID and Network Key
When  manually setting up  a wireless connection,  you need to  specify  the  SSID  and  network key  of your wireless router. The SSID  and
network key  may  be indicated  on  these networking devices.  Check your devices and  write down the  necessary  information  before se tting
up  the  connection.  For more information, see  the  instruction  manuals  for  your networking devices or contact your manufacturer.
SSID A name given  for  identifying a specific...

Read the License Agreement and  click [Yes]  to agree.
Check  the information  displayed  for the wireless router.
Write down the  necessary  information. If  you do not  know what information  is  necessary, write down all the  information  that  is
displayed.
NOTE:
If wireless routers are not  found
Click [Refresh].  If  nothing happens, check  that  the  settings are  correctly configured on  the  computer  and  the  wireless router.
LINKS
Connecting to a Wireless LAN (MF8580Cdw  / MF8280Cw Only)...

0ALJ-083
Setting IP Addresses
Connecting the  machine to  a network requires  a unique  network IP  address. Two versions  of IP  addresses are  available: IPv4  and  IPv6.
Configure these settings depending on  the  network environment. To use IPv6  addresses,  you need to  properly  configure the  IPv4  a ddress
settings.
>ß>ß>ä>Ì>Û>Ì>â>ã>â
 

0ALJ-084
Setting IPv4 Address
The machine's  IPv4  address can be either assigned  automatically by a dynamic IP  addressing protocol, such as
DHCP, or entered  manually.  When  connecting the  machine to  a wired LAN, make sure  that  the  connectors of
the  LAN cable are  firmly inserted into the  ports (
Connecting to a Wired  LAN). You  can test the  network
connection if  necessary.
Setting IPv4  Address
Testing the Network Connection
Press  .
Use  / to select ,  and  press  .
If  the  logon...

4Press  .
NOTE:
IP  addresses assigned  via  DHCP/BOOTP/RARP override the  address obtained via  Auto  IP.
Manually entering an IP address
1Check that  is  set  to .
If   is  displayed,  select  , and  set both    and   to  .
2Select , and  press .
3Specify  the IP address,  subnet mask, and  gateway  address (or default gateway). Specify the  settings in the  following  order: 
 .
Enter the  setting using the  numeric keys, and  press  on  each screen.
Restart the machine.
Turn  OFF  the  machine, wait...