Canon Eos Rebel Xt 350d Instruction Manual

							
121
You do the direct printing procedure entirely through your camera’s LCD monitor.
1Select [Communication].
¡Select the [ b] tab.
¡ Press the < V> key to select 
[ Communication ], then press .
2Select [Print/PTP].
¡ Press the < V> key to select [ Print/
PTP ], then press < 0>.
1Turn the camera’s power switch 
to < 2 >.
2Set up the printer.
¡For details, refer to the printer’s 
manual.
Preparing to Print
Setting the Camera
Connecting the Camera to the Printer
When connecting the camera to a personal computer, set 
[Communication ] to [PC connection ].Communication between the camera 
and personal computer will not work if [ Print/PTP] is set.
¡RAW images are not compatible with direct printing.
¡ Do not disconnect the cable during direct printing.  
						

							
Preparing to Print
122
3Connect the camera to the 
printer.
¡Refer to the table (Printers and 
Cables) below to select the proper 
cable to connect the camera to 
printer.
¡ When connecting the cable plug to 
the camera’s < C> terminal, the 
cable plug’s < D> icon must face the 
front side of the camera.
¡ To connect to the printer, refer to the 
printer’s instruction manual.
4Turn on the printer.
5Turn the camera’s power switch 
to < 1>.
sSome printers may have a beeping 
sound.
Printers and Cables
Printer CompatibilitySuitable Cable
PictBridge 
only
Interface cable provided with camera
The plug at both ends have the < D>
icon.PictBridge  and
CP Direct
PictBridge  and
Bubble Jet Direct
CP Direct  onlyCable provided with printer
Only one plug has the < D> icon.
Bubble Jet Direct  only
w
w A
w S
A
S  
						

							
123
Preparing to Print
6Playback the image.
¡Press the < x> button.
s The image will appear and one of 
three icons < w/A /S > will appear 
on the upper left to indicate that the 
camera is connected to the 
respective type of printer.
s The Direct print button lamp will light 
in blue.
¡ The procedure will be different 
depending on the icon displayed. See 
the applicable pages below.
SBubble Jet Direct
ACP Direct
wPictBridge
IconReference pages
124 - 127, 136
128 - 130, 136
131 - 133, 136
w
A
S
¡ If the camera is running by battery power, make sure it is fully charged. 
During direct printing, keep checking the battery level.
¡ If there is a long beeping sound in step 5, it indicates a problem with the 
PictBridge printer. To find out what’s wrong, do the following:
Press the < x> button to playback the image and follow the steps below.
1. Press < 0>.
2. On the print setting screen, select [ Print].
The error message will be displayed on the LCD monitor. See “Error 
Messages” on page 127.
¡ Before disconnecting the cable, turn off the camera and printer. Pull out 
the cable while holding the plug, not the cord.
¡ When connecting the camera to the printer, do not use any cable other 
than the dedicated interface cable.
For direct printing, using AC Adapter Kit ACK-DC20 (optional) to power the 
camera is recommended.  
						

							
124
The setting options will differ depending on the printer. Some 
settings might be disabled. For details, refer to your printer’s instruction 
manual.
1Select the image(s) to be printed.
¡ Check that the < w> icon is 
displayed on the upper left of the LCD 
monitor.
¡ Press the < U> key to select the 
image to be printed.
2Press .
s The Print setting screen will appear.
3Select [Paper Settings].
¡Press the < V> key to select [ Paper
settings ], then press < 0>.
s The Paper settings screen will 
appear.
w Printing with PictBridge
Printer-connected icon
Print setting screen
* Depending on your printer, certain settings like date imprinting and 
trimming might not be available. Set the date imprinting to on or off.
Set the printing effects.
Set the quantity to be printed.
Set the trimming area.
Set the paper size, type, and layout.
Returns to the screen in step 1.
Starts the printing.
The paper size, type, and layout you have set will be displayed.  
						

							
125
wPrinting with PictBridge
¡Press the < V> key to select the 
size of the paper loaded in the printer, 
then press < 0>.
s The Paper Type screen will appear.
¡ Press the < V> key to select the 
type of the paper loaded in the 
printer, then press < 0>.
s The Page Layout screen will appear.
About the Paper Types
If you are using a Canon PIXMA/DS/BJ printer with Canon paper, set 
the respective paper type as follows:
If you are using a non-Canon printer, refer to the printer’s instruction 
manual.
¡Press the < V> key to select the 
desired layout, then press < 0>.
s The Print setting screen will reappear.
TSetting the Paper Size
YSetting the Paper Type
Photo Photo Paper Plus Glossy
Fast PhotoPhoto Paper Pro
DefaultPhoto Paper Plus Glossy
USetting the Layout  
						

							
wPrinting with PictBridge
126
Layout Settings
4Set the other options.
¡If desired, also set the < H> date 
imprinting, < E> printing effects, and 
< R > number of copies.
¡ Press the < V> key to select the 
desired option.
¡ Press the < U> key to select the 
desired setting.
¡ Depending on the BJ printer, the 
 Printing effects setting may 
enable you to select the [ Vivid] (for 
vivid greens and blue sky), [ NR]
(noise reduction), [ Vivid+NR] or [On]
setting.
¡ For details on trimming, see page 
134.
Borderless The print will have no borders.
If your printer cannot print borderless prints, the print will have 
borders.
BorderedThe print will have a white border along the edges.
**-upOption to print 2, 4, 8, 9, 16, or 20 copies of same image on one sheet.
DefaultWith a Canon printer, the default is borderless.
HDate imprintingEPrinting effectsRNumber of copies  
						

							
127
wPrinting with PictBridge
5Start printing.
¡Press the < V> key to select [ Print],
then press < 0>.
s The printing will start.
¡ When the printing ends, the screen 
will return to step 1.
¡ To stop the printing, press < 0> while 
[ Stop ] is displayed, then select [ OK]
and press < 0>.
¡ Depending on the image’s file size and recording quality, it may take 
some time for the printing to start after you select [ Print].
¡ The [ Default ] setting for printing effects and other options are the 
printer’s own default settings as set by the printer’s manufacturer. See 
the printer’s instruction manual to find out what the [ Default]  settings 
are.
Handling Printer ErrorsIf you resolve a printer error (no ink, no paper, etc.) and select [ Continue] to 
resume printing but it does not resume, operate the buttons on the printer to 
resume printing. For details, see the printer’s instruction manual.
Error MessagesIf a problem occurs during printing, an error message will appear on the 
camera’s LCD monitor. Press < 0> to stop printing. After resolving the 
problem, resume printing. For details on how to resolve a problem with the 
printer, refer to the printer’s instruction manual.
Paper Error Check whether the paper is properly loaded in the printer.
Ink Error The printer has run out of ink or the waste ink tank is full.
Hardware Error Check for any printer problems other than paper and ink problems.
File Error The selected image cannot be printed via PictBridge.
Images taken with a different camera or images edited with a computer 
might not be printable.  
						

							
128
1Select the image to be printed.
¡Check that the < A> icon is displayed 
on the upper left of the LCD monitor.
¡ Press the < U> key to select the 
image to be printed.
2Press < 0>.
s The Print setting screen will appear.
3Select [Style].
¡Press the < V> key to select 
[ Style ], then press < 0>.
s The Style screen will appear.
A Printing with CP Direct
Printer-connected icon
Print setting screen
Set the quantity to be printed.
Set the trimming area.
Set the printing style.
Returns to the screen in step 1.
Starts the printing.
The printing style settings are displayed.
<
H> is the date icon.  
						

							
129
A Printing with CP Direct
4Set the options as desired.
¡ Set the [ Image], [Borders ], and 
[ Date ] as desired.
¡ Press the < V> key to select the 
desired option, then press < 0>.
¡ Press the < V> key to select the 
desired setting, then press < 0>.
¡ [Image ] is selectable when credit 
card-size paper is used. If you select 
[ Multiple ], 8 small images of the 
same picture will be printed on the 
paper.
¡ Check the [ Borders] and [Date]
settings and set them if necessary.
¡ When you are done, press the 
 button to return to the Print 
setting screen.
5Set the number of copies.
¡ Set as necessary.
¡ Press the < V> key to select 
[ copies ].
¡ Press the < U> key to set the 
desired quantity.
¡ Set a number from 1 to 99.
[Image][Borders][Date]  
						

							
A Printing with CP Direct
130
6Set the trimming.
¡ Set as necessary.
¡ For details on trimming, see page 
134.
7Start printing.
¡Press the < V> key to select [ Print],
then press < 0>.
s The printing will start.
¡ When the printing ends, the screen 
will return to step 1.
¡ To stop the printing, press < 0> while 
[ Stop ] is displayed, then select [ OK]
and press < 0>.
¡ The date may look light if it is imprinted on a bright background or border.
¡ If [Multiple ] is selected, [ Borders] and [Date] cannot be selected. 
[ Borderless ] will be set and [ Date] will be set to [ Off]. The image will 
also be cut off along all four edges.
¡ If [Date ] is [On], the date recorded for the image will appear on the 
print.The date will appear on the lower right of the image.
¡ If you select [ Stop] while printing only one image, the printing will not 
stop until it finishes printing the image. If you are printing multiple 
images, the printing will stop after the current image is finished printing.
¡ If a problem occurs during printing, an error message will appear on the 
camera’s LCD monitor. Select [ Stop] or [Resume ] (after resolving the 
problem). If [ Resume] is not displayed, select [ Stop].