Canon Eos Rebel T6i 750d Instruction Manual

							291
k Playing Back Movies
Movie Playback Panel
* When background music is set, the movie sound will not be played back.
OperationPlayback Description
7 PlayPressing  toggles between play and stop.
8 Slow motionAdjust the slow motion speed by pressing the < Y> < Z> 
keys. The slow motion speed is indicated on the upper right 
of the screen.
5  First frameDisplays the movie’s first frame.
3 Previous 
frameEach time you press < 0>, the previous frame is displayed. 
If you hold down < 0>, it will rewind the movie.
6 Next frameEach time you press < 0>, the movie will play frame-by-
frame. If you hold down < 0>, it will fast forward the movie.
4 Last frameDisplays the movie’s last frame.
F Background 
music*Plays back a movie with the selected background music 
(p.297).
X  EditDisplays the editing screen (p.292).
Playback position
mm’ ss”Playback time (m inutes:seconds)
9 Vo l u m eTurn the  dial to adjust the volume of the built-in 
speaker (p.290).
3 2Press the < M> button to return to the single-image 
display.
With a fully-charged Battery Pack LP-E17, the continuous playback time at 
room temperature (23°C / 73°F) is approx. 2 hr. 20 min.
 If you connect the camera to a TV set to play back a movie (p.298, 301), 
adjust the sound volume with the TV set. (Turning the < 6> dial will not 
change the sound volume.)
 If you take a still photo while you are shooting the movie, the still photo 
will be displayed for approx. 1 sec. during the movie playback. 
						

							X Editing a Movie’s First and Last Scenes
292
Ta p  [7] on the center of the screen.
 The movie will start playing back.
 To display the movie playback panel, 
tap < s1 > on the upper left of the 
screen.
 To pause the movie while it is playing 
back, tap on the screen. The movie 
playback panel will also appear.
Playback with the Touch Screen
X Editing a Movie’s First and Last Scenes
You can edit out the first and last scenes of a movie in approx. 1-sec. increments.
1On the movie playback screen, 
select [ X].
 The movie editing panel will be 
displayed at the bottom of the screen.
2Specify the part to be edited out.
 Select either [U] (Cut beginning) or 
[V ] (Cut end), then press < 0>.
 Press the < Y> < Z> keys to see the 
previous or next frames. Holding 
down the key will fast forward or fast 
rewind the frames.
 After deciding which part to edit out, 
press . The portion highlighted 
in gray on the top of the screen will 
remain. 
						

							293
X Editing a Movie’s First and Last Scenes
3Check the edited movie.
 Select [ 7] and press < 0> to play 
back the edited movie.
 To change the editing, go back to step 
2.
 To cancel the editing, press the 
 button, then select [ OK] on 
the confirmation dialog.
4Save the edited movie.
 Select [ W], then press < 0>.
 The save screen will appear.
 To save it as a new movie, select 
[New file ]. To save it and overwrite 
the original movie file, select 
[Overwrite ], then press < 0>.
 On the confirmation dialog, select 
[OK ], then press < 0> to save the 
edited movie and return to the movie 
playback screen.
 Since the editing is performed in ap prox. 1-sec. increments (position 
indicated by [ Z] on the top of the screen), the actual position where the 
movie is edited may differ fr om the position you specified.
 If the card does not have enough free space, [ New file] will not be 
available.
 When the battery level is low, movie editing is not possible. Use a fully-
charged battery. 
						

							294
You can play back the images on the card as an automatic slide show.
1Select [Slide show].
Under the [x 2] tab, select [Slide 
show ], then press < 0>.
2Select the images to be played 
back.
 Press the < W> < X> keys to select 
the desired option, then press < 0>.
All images/Movies/Stills
 Press the < W> < X> keys to select 
one of the following: [ OAll images ] 
[k Movies] [ zStills]. Then press 
< 0 >.
Date/Folder/Rating
 Press the < W> < X> keys to select 
one of the following: [ iDate ] 
[
nFolder ] [9Rating ].
 When < zH> is highlighted, 
press the < B> button.
 Press the < W>  keys to select an 
option, then press < 0>.
3  Slide Show (Auto Playback)
Number of images 
to be played back
[Date][ Folder][ Rating] 
						

							295
3 Slide Show (Auto Playback)
3Configure [Set up] as desired.
Press the < W> < X> keys to select 
[Set up ], then press < 0>.
 Set the [Display time], [ Repeat] 
(repeated playback), [ Transition 
effect ] (effect when changing 
images), and [Background music ] 
for the still photos.
 The background music selection 
procedure is explained on page 297.
 After selecting the settings, press the 
 button.
ItemPlayback Description
OAll imagesAll the still photos and movies  on the card will be played 
back.
i DateStill photos and movies taken on the selected shooting date 
will be played back.
n Folder Still photos and movies in the selected folder will be played 
back.
k
MoviesOnly the movies on the card will be played back.
zStillsOnly the still photos on  the card will be played back.
9 Rating Only the still photos and movi
es with the selected rating will 
be played back.
[Display time] [Repeat] 
						

							3 Slide Show (Auto Playback)
296
4Start the slide show.
Press the < W>< X> keys to select 
[Start ], then press < 0>.
 After [ Loading image... ] is displayed, 
the slide show will start.
5Exit the slide show.
 To exit the slide show and return to 
the setting screen, press the < M> 
button.
[Transition effect][ Background music]
To pause the slide show, press < 0>. During pause, [ G] will be displayed 
on the upper left of the image. Press < 0> again to resume the slide 
show. You can also pause the sli de show by tapping on the screen.
 During auto playback, you can press the < B> button to change the 
still photo display format (p.97).
 During movie playback, you can adjust the sound volume by turning the 
 dial.
 During auto playback or pause, you can press the < Y> < Z> keys to 
view another image.
 During auto playback, auto power off will not take effect.
 The display time may vary depending on the image.
 To view the slide show on a TV set, see page 298. 
						

							297
3 Slide Show (Auto Playback)
After you use EOS Utility (EOS software) to copy background music to 
the card, you can play background music together with the slide show.
1Select [Background music].
Set [ Background music ] to [On], 
then press < 0>.
 If the card has no background music, 
you cannot perform step 2.
2Select the background music.
Press the < W> < X> keys to select 
the desired background music, then 
press < 0>. You can also select 
multiple background music tracks.
3Play the background music.
 To listen to a sample of the 
background music, press the < B> 
button.
 Press the < W> < X> keys to play 
another background music track. To 
stop listening to the background 
music, press the < B> button 
again.
 Adjust the sound volume by turning 
the < 6> dial.
 To delete a background music track, 
press the < W> < X> keys and select 
the track, then press the < L> button.
Selecting the Background Music
At the time of purchase, the camera does not have background music. The 
procedure to copy background music to a card is explained in the EOS 
Utility Instruction Manual (p.406). 
						

							298
You can view still photos and movies on a TV set.
HDMI Cable HTC-100 (sold separately) is required.
1Connect the HDMI cable to the 
camera.
With the plug’s  logo 
facing the front of the camera, insert it 
into the < D > terminal.
2Connect the HDMI cable to the TV 
set.
Connect the HDMI cable to the TV 
set’s HDMI IN port.
3Turn on the TV set and switch the 
TV set’s video input to select the 
connected port.
4Set the camera’s power switch to 
.
Viewing Images on a TV Set
Viewing on High-Definition (HD) TV Sets (Connected with HDMI)
 If the video system format does not match the TV set’s, movies will not 
be displayed properly. In such a case, switch to the proper video system 
format with [ 53: Video system ].
 If [51: Wi-Fi/NFC ] is set to [Enable ], the camera cannot be connected to 
a TV set. Set [ Wi-Fi/NFC] to [Disable ], then reconnect the camera to the 
TV set with an HDMI cable or stereo AV cable.
 Adjust movie sound volume with the TV set. The sound volume cannot 
be adjusted with the camera.
 Before connecting or disconnecting the cable between the camera and 
TV set, turn off the camera and TV set.
 Depending on the TV set, part of the image displayed may be cut off. 
						

							299
Viewing Images on a TV Set
5Press the  button.
The image will appear on the TV 
screen. (Nothing will be displayed on 
the camera’s LCD monitor.)
 The images will automatically be 
displayed at the optimum resolution 
of the TV set.
 By pressing the < B> button, you 
can change the display format.
 To play back movies, see page 290.
If the TV set connected to the camera with an HDMI cable is compatible 
with HDMI CEC*, you can use the TV set’s remote control for playback 
operations.
* An HDMI-standard function enabling HDMI devices to control each other so that you can control them with one remote control unit.
1  Set [Ctrl over HDMI] to [Enable].
 Under the [ 32] tab, select [Ctrl over 
HDMI], then press < 0>.
 Select [ Enable], then press < 0>.
Using HDMI CEC TV Sets
The images cannot be output at the same time from both the < D> 
and < q > terminals.
Do not connect any other device’s output to the camera’s < D> 
terminal. Doing so may cause a malfunction.
 Certain TV sets may not be able to display the captured movies. In such 
a case, use the stereo AV cable AVC-DC400ST (sold separately) to 
connect to the TV set. 
						

							Viewing Images on a TV Set
300
2Connect the camera to a TV set.
Use an HDMI cable to connect the 
camera to the TV set.

The TV set’s input will switch 
automatically to the HDMI port 
connected to the camera. If it does not 
switch automatically, use the TV set’s 
remote control to select the HDMI IN 
port the cable is connected to.
3Press the camera’s < x> button.
An image will appear on the TV 
screen and you can use the TV set’s 
remote control to play back images.
4Select an image.
 Point the remote control toward the 
TV set and press the  /  button to 
select an image.
5Press the remote control’s Enter 
button.
The menu appears and you can perform 
the playback operations shown on the left.
Press the / button to select the 
desired option, then press the Enter 
button. For a slide show, press the 
remote control’s 
/ button to select 
an option, then press the Enter button.
 If you select [ Return] and press the 
Enter button, the menu will disappear 
and you can use the  / button to 
select an image.
2: Return
a : 9-image index
1: Play movie
c : Slide show
B : Display shooting info
b : Rotate
Still photo playback menu
Movie playback menu
Some TV sets require you to first enable the HDMI CEC connection. For 
details, refer to the TV set’s instruction manual.
 Certain TV sets, even those compatible with HDMI CEC, may not 
operate properly. In such a case, set [ 32: Ctrl over HDMI ] to [Disable], 
and use the camera to control the playback operation.