Canon EOS Rebel T5 1200D User Guide

							201
3 Manual Sensor CleaningN
 While cleaning the sensor, never do any of the following. If the 
power is cut off, the shutter will close and the shutter curtains and 
image sensor may get damaged.
• Setting the power switch to .
• Opening the card slot/battery compartment cover.
 The surface of the image sensor is extremely delicate. Clean the sensor 
with care.
 Use a plain blower without any brush attached. A brush can scratch the 
sensor.
 Do not insert the blower tip inside the camera beyond the lens mount. If 
the power is turned off, the shutter will close and the shutter curtains or 
reflex mirror may get damaged.
 Never use pressurized air or gas to clean the sensor. The blowing force 
can damage the sensor or the spray gas can freeze on the sensor and 
scratch it.
 If the battery level becomes low while you clean the sensor, the beeper 
will sound as a warning. Stop cleaning the sensor.
 If a smudge that cannot be removed with a blower remains, having the 
sensor cleaned by a Canon Service Center is recommended. 
						

							203
8
Image Playback
This chapter explains functions related to viewing 
photos and movies, with more detail than in Chapter 2 
“Basic Shooting and Image Playback”. Here you will 
find explanations of how to play back and erase photos 
and movies with the camera and view them on a TV set.
Images shot and saved with another deviceThe camera may not be able to properly display images captured 
with a different camera, edited with a computer, or that have had their 
file names changed. 
						

							204
Search for images quickly with the index display showing four or nine 
images on one screen.
1Play back the image.
 When you press the  button, the 
last image captured will be displayed.
2Switch to the index display.
 Press the  button.
XThe 4-image index display will 
appear. The selected image is 
highlighted in an orange frame.
 Press the  button again to 
switch to the 9-image display.
 Pressing the  button will switch 
the display between nine images, four 
images and one image displayed.
3Select an image.
 Press the  cross keys to move 
the orange frame to select an image.
 
Turni ng t he  dial will display 
image(s) on the next or previous screen.
 Press  in the index display to 
display the selected image as a 
single image.
x Searching for Images Quickly
H Display Multiple Images on One Screen (Index Display)
ÎÎ 
						

							205
x Searching for Images Quickly
In the single-image display, you can turn the  dial to jump through 
the images forward or backward according to the jump method set.
1Select [Image jump w/6].
 Under the [x2] tab, select [Image 
jump w/6], then press .
2Select the jump method.
 Press the  cross keys to select 
the jump method, then press .
d: Display images one by one
e: Jump 10 images
f: Jump 100 images
g: Display by date
h: Display by folder
i: Display movies only
j: Display stills only
k: Display by image rating (p.208)
Turn the  dial to select.
3Browse by jumping.
 Press the  button to play back 
images.
 In the single-image display, turn the 
 dial.
XYou can browse images with the 
method you have set.
I Jump through Images (Jump Display)
Playback position Jump method
 To search images according to the shooting date, select [Date].
 To search images according to folder, select [Folder].
 If the card contains both movies and still photos, select [Movies] or 
[Stills] to display only one or the other.
 If no images match the selected [Rating], you cannot browse through the 
images with the  dial. 
						

							206
You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor.
1Magnify the image.
 Press the  button during image 
playback.
XThe image will be magnified.
 If you hold down the  button, the 
image will be magnified until it 
reaches the maximum magnification.
 Press the  button to reduce 
the magnification. If you hold down 
the button, the magnification will be 
reduced to the single-image display.
2Scroll around the image.
 Use the  cross keys to scroll 
around the magnified image.
 To exit magnified view, press the 
 button and the single-image 
display will reappear.
u/y Magnified View
Magnified area position
 In magnified view, you can turn the  dial to view another image at 
the same magnification.
 The image cannot be magnified during the image review immediately 
after shooting.
 A movie cannot be magnified. 
						

							207
You can rotate the displayed image to the desired orientation.
1Select [Rotate image].
 Under the [x1] tab, select [Rotate 
image], then press .
2Select an image.
 Press the   keys to select 
the image to be rotated.
 You can also select an image in the 
index display (p.204).
3Rotate the image.
 Each time you press , the image 
will rotate clockwise as follows: 
90° 9 270° 9 0°.
 To rotate another image, repeat steps 
2 and 3.
 To exit and return to the menu, press 
the  button.
b Rotating the Image
 If you have set [51: Auto rotate] to [OnzD] (p.188) before taking 
vertical shots, you need not rotate the image as described above.
 If the rotated image is not displayed in the rotated orientation during 
image playback, set [51: Auto rotate] to [OnzD].
 A movie cannot be rotated. 
						

							208
You can rate images (still photos and movies) with one of five rating marks: l/m/n/o/p. This function is called rating.
1Select [Rating].
 Under the [x2] tab, select [Rating], 
then press .
2Select an image.
 Press the   keys to select a 
still photo or movie to be rated.
 You can display three images by 
pressing the  button. To 
return to the single-image display, 
press the  button.
3Rate the image.
 Press the   keys to select a 
rating.
XThe total number of images rated will 
be counted and displayed for each 
rating.
 To rate another image, repeat steps 2 
and 3.
 To return to the menu, press the 
 button.
3 Setting Ratings 
						

							
209
3 Setting Ratings
The total number of images with a given rating that can be displayed is up to 
999. If there are more than 999 images with a given rating, [ ###] will be 
displayed for that rating.
Taking Advantage of Ratings  With [ x2: Image jump w/ 6], you can display only images with a 
specific rating.
  With [ x2: Slide show ], you can play back only images with a specific 
rating.
  With Digital Photo Professional (EOS software, p.318), you can select 
only images with a specific  rating (still photos only).
  With Windows 8.1, Windows 8, or  Windows 7, etc., you can see each 
file’s rating as part of the file information display or in the provided image 
viewer (still photos only). 
						

							210
During single-image display, you can press the  button to set any 
of the following: [ : Protect images], [b: Rotate image], [9: 
Rating], [U: Creative filters], [S: Resize (JPEG images only)], [e: 
Image jump w/6].
For movies, only the functions in bold above can be set.
1Press the  button.
 During image playback, press the 
 button.
XThe Quick Control options will 
appear.
2Select a function and set it.
 Press the   keys to select a 
function.
XThe name and current setting of the 
selected function are displayed at the 
bottom of the screen.
 Set it by pressing the   
keys.
 For Creative filters and Resize, press 
 and set the function. For 
details, see page 234 for Creative 
filters and page 237 for Resize. To 
cancel, press the  button.
3Exit the setting.
 Press the  button to exit the 
Quick Control screen.
Q Quick Control for Playback