Canon Digital IXUS 30 User Manual

							109
Playback
Editing Movies
Selecting   (Edit) in the movie control panel enables you to cut unwanted 
portions at the start or end of a movie clip.
Protected movies and movies less than 1 second in duration cannot 
be edited.
1Use the   or   button to select a 
movie and press the FUNC./SET 
button.
2Switch to the movie editing mode.
See Operating the Movie Control Panel (p. 
107).
 The movie editing panel and the movie 
editing bar will display.
3Use the   or   button to select 
 or   and the   or   button 
to set the portion to which the cut is 
applied.
: Cut Beginning
: Cut End
: Cursor
Movie Editing Bar
Movie Editing Panel
 
						

							110
 The minimum duration of a movie that can be edited is 1 second.
 It may take approximately 3 minutes to save an edited movie. If the 
battery pack runs out of charge partway through, edited movie clips 
cannot be saved. When editing movies, use a fully charged battery 
pack or the separately sold AC Adapter Kit ACK-DC10 (p. 154).
4Use the   or   button to select 
 (Play) and press the FUNC./SET 
button.
 A preview of the temporarily edited movie 
clip plays.
 To stop it, press the FUNC./SET button 
again.
5Use the   or   button to select 
 (Save) and press the FUNC./
SET button.
Selecting   (Exit) cancels the edits and 
returns to the movie control panel display.
6Use the   or   button to select 
[New File] or [Overwrite] and press 
the FUNC./SET button.
 [New File] saves the edited movie under a 
new file name. The pre-edit data is left 
unchanged. 
Note, if you press the FUNC./SET button 
while saving the movie, saving is 
canceled.
 [Overwrite] saves the edited movie with its 
original file name. The pre-edit data is lost.
 When the SD card lacks sufficient space to 
create a new file, only [Overwrite] can be 
selected. 
 
						

							111
Playback
Rotating Images in the Display
Images can be rotated clockwise 90° or 270° in the display.
 Movies cannot be rotated.
 When images are downloaded to a computer, the orientation of 
images rotated by the camera will depend upon the software used 
to download the images.
 Images can be magnified when rotated (p. 104).
 Images taken vertically with Auto Image Rotate (p. 99) set to [On] 
will automatically be rotated to the vertical position when viewed on 
the camera’s LCD monitor.
1In the   (Play) menu, select   
and press the FUNC./SET button.
See Selecting Menus and Settings (p. 49).
2Use the   or   button to select 
the image to be rotated and press 
the FUNC./SET button.
Cycle through the 90°/270°/0° orientations 
with each press of the FUNC./SET button.
3Press the MENU button.
The display will return to the Play menu. 
Pressing the MENU button again returns to the 
playback screen.
0° (Original) 90° 270°
 
						

							112
Attaching Sound Memos to Images
In playback mode (including single image playback, index playback, and 
magnifying playback), you can attach sound memos (up to 60 seconds) to 
an image. The sound data is saved in the WAVE format.
Exiting Sound Memos
Press the MENU button.
1In the   (Play) menu, select   
and press the FUNC./SET button.
See Selecting Menus and Settings (p. 49).
2Use the   or   button to select an 
image and press the FUNC./SET 
button.
The sound memo control panel will display.
3Use the   or   button to select 
 (Record) and press the FUNC./
SET button to record.
 The recording starts and the elapsed time 
is displayed. 
 Press the FUNC./SET button again to stop 
recording. To resume recording, press the 
FUNC./SET button again.
 Up to 60 seconds of recordings may be 
added to any one image.
 To return to the previous screen, select 
 (Exit) and press the FUNC./SET 
button.
Sound Memo Panel
 
						

							113
Playback
Playing/Erasing Sound Memos
 You cannot attach sound memos to movies.
 The “Memory card full” message will display when the SD card is full 
and you will be unable to record sound memos to that card.
 If an incompatible sound memo is attached to an image, you will be 
unable to record or play sound memos for that image, and the 
“Incompatible WAVE format” message will display. You can erase 
incompatible sound data using the camera.
 Sound memos for protected images cannot be erased.
The volume can be adjusted in the   (Set up) menu (p. 55).
1Display an image with a sound 
memo attached (p. 112) and press 
the FUNC./SET button.
 Images with sound memos attached have 
the   icons displayed on them.
 The sound memo control panel will 
display.
2Use the   or   button to select 
 (Play) or   (Erase) and press 
the FUNC./SET button.
 (Play)
 The sound memo will play. Playback will 
stop when you press the FUNC./SET 
button. Press the FUNC./SET button again 
to resume playback.
 Use the   or   button to adjust the 
sound volume.
 (Erase)
A confirmation menu will display. Use the 
 or   button to select [Erase] and press 
the FUNC./SET button.
To return the playback to the beginning, 
select   (Pause) while stopped and press 
the FUNC./SET button.
Sound Memo Panel
 
						

							114
Automated Playback (Slide Shows)
Starting a Slide Show
A selection of images or all the images on an SD card can be displayed one-
by-one in an automated slide show.
Slide show image settings are based on DPOF standards (p. 124).  
All ImagesPlays all images on the SD card in order.
Slide Show 1-3
Plays the images selected for each slide show in order (p. 115).
1In the   (Play) menu, select   
and press the FUNC./SET button.
See Selecting Menus and Settings (p. 49).
 The Slide Show menu will display.
2Use the   or   button to select 
[Program] and the   or   button 
to select [All Images], [Show 1], 
[Show 2] or [Show 3].
See p.116 from step 3, for selecting the 
playback images in slide shows 1-3.
3Use the   or   button to select 
[Start] and press the FUNC./SET 
button.
The slide show starts. The Slide Show menu 
will reappear after the playback ends.
 
						

							115
Playback
 Movies play for their entire recorded length regardless of the time 
set in the slide show settings.
 The power-saving function does not activate during a slide show 
(p. 55). 
Pausing/Resuming a Slide Show
Fast Forwarding/Rewinding a Slide Show
Stopping a Slide Show
Selecting Images for Slide Shows
You can mark images for inclusion in slide shows 1-3. Up to 998 images may be 
marked per slide show. Images display in the order of their selection.
4Press the MENU button.
The display will return to the Play menu. 
Pressing the MENU button again returns to 
the playback screen.
Press the FUNC./SET button.
The slide show pauses. Press the FUNC./
SET button again to restart it.
Press the  or  button.
The previous or next image displays. Hold 
down the button to advance through the 
images more rapidly.
Press the MENU button.
The slide show stops and the Slide Show 
menu reappears.
1Display the Slide Show menu.
See Starting a Slide Show (p. 114).
 
						

							116
2Use the   or   button to select 
[Program] and 
the  or  button to 
select [Show 1], [Show 2] or [Show 3].
A white checkmark will appear beside a 
show already containing images.
3Use the   or   button and the   
or   button to choose [Select] and 
press the FUNC./SET button.
4Select images for the Slide Show
 Use the   or   button to move between 
images and the   or   button to select 
or deselect them. Selected images display 
a number corresponding to their selection 
order and a white checkmark  .
 You can press the zoom lever toward   
to switch to the index mode (3 images) 
and use the same procedures to select 
images.
 While in index playback, pressing the 
FUNC./SET button displays the menu for 
selecting or deselecting all images. Use 
the   or   button to select [Mark all] 
or [Clear all] and press the FUNC./SET 
button.
5Press the MENU button.
Press the MENU button repeatedly until the 
Playback screen reappears to finish the 
procedure.
 
						

							117
Playback
Adjusting the Play Time and Repeat Settings
You can change the play time for all the images in a show and have the 
show repeat continuously. 
 The display interval may vary slightly from the set time for some 
images when played.
 Slide shows are easy to arrange on a computer with the supplied 
software (ZoomBrowser EX/ImageBrowser). See the Canon Digital 
Camera Software Starter Guide Disk.
Play TimeSets the duration that each image displays. Choose between 3-10 
seconds, 15 seconds, 30 seconds and Manual.
RepeatSets whether the slide show stops when all the slides have been 
displayed or continues until stopped.
1Display the Slide Show menu.
See Starting a Slide Show (p. 114).
2Use the   or   button to select 
[Set up] and press the FUNC./SET 
button.
3Use the   or   button to select 
[Play Time] or [Repeat] and the   
or   button to select an option.
4Press the MENU button.
The set up menu will close. Pressing the MENU 
button again returns to the Play menu. Press it 
again to go back to the playback screen.
 
						

							118
Protecting Images
You can protect important images and movies from accidental erasure.
To Cancel Protection
After step 1, select an image to remove protection from and press the 
FUNC./SET button.
Please note that formatting (initializing) an SD card erases all data, 
including protected images (p. 28).
1In the   (Play) menu, select   
and press the FUNC./SET button.
See Selecting Menus and Settings (p. 49).
2Use the   or   button to select an 
image to protect and press the 
FUNC./SET button.
 The   icon appears on protected images.
 You can make the selection of images 
easier by toggling between single image 
playback and index playback by pressing 
the zoom lever toward   or  .
3Press the MENU button.
The Play menu displays again. Press it again 
to return to the playback screen.
Protection Icon