Canon Digital IXUS 220 HS User Manual

							
Viewing Images in Filtered Playback
121
Filtered playback
In filtered playback (Step 3), you can view filtered images with “Quickly Searching 
Images”  (p. 118), “Viewing Slideshows”  (p. 122), and “Magnifying Images” 
(p. 125) . You can process all filtered images  at once while performing operations 
in “Protecting Images”  (p. 134), “Erasing Images”  (p. 138), or “Choosing Images 
for Printing (DPOF)”  (p. 159), by choosing all of the filtered images.
However, if you change the category  (p. 142), or edit an image and save it as a 
new image  (p. 146), a message will appear, and filtered playback will cancel.
 
						

							122
You can automatically play back images recorded to a memory card. Each 
image displays for approximately 3 seconds.
Choose ..
zAfter pressing the m button, press the 
op buttons to choose ., then press the 
m button again.
Choose a transition effect.
zPress the op buttons to choose an 
effect, then press the m button.
XThe slideshow will start a few seconds 
after [Loading image...] appears.
zIn filtered playback (p. 120), only images 
matching a filter play back. In group 
playback (p. 126), only grouped images 
play back.
zYou can pause/restart a slideshow by 
pressing the m button again.
zPress the n button to stop the 
slideshow.
Viewing Slideshows
•If you press the qr buttons during playback, the image will switch. If you 
keep the qr buttons pressed, you can fast-forward through images.
•The power saving function (p. 52) does not work during slideshows.
 
						

							Viewing Slideshows
123
Changing Settings
You can set a slideshow to repeat, or change transition effects and the time 
that slideshow images are displayed. You can choose from 6 transition 
effects when switching between images.
Choose [Slideshow].
zPress the n button to choose 
[Slideshow] from the 1 tab, then press the 
m button.
Choose a setting.
zPress the op buttons to choose an item, 
then press the qr buttons to adjust the 
setting.
zIf you choose [Start] and press the m 
button, the slideshow starts with your 
settings.
zPress the n button to restore the 
menu screen.
You cannot change [Play Time] if [Bubble] is chosen in [Effect].
 
						

							124
You can magnify the area of a recorded image that was inside the AF Frame 
to check the focus.
Press the p button to switch to the 
focus check display (p. 44).
XA white frame will appear where the AF 
frame was when the focus was set.
XA gray frame will appear on a face 
detected during playback.
XThe area within the orange frame appears 
magnified.
Switch frames.
zMove the zoom lever toward k once.XThe screen shown on the left will appear.zPress the m button to move to a different 
frame when multiple frames appear.
Change the magnification level or 
location.
zUse the zoom lever to change the display 
size, and the opqr buttons to change 
the display position while checking the 
focus.
zPress the n button to reset the 
display to Step 1.
Checking the Focus
The focus check display is not available for movies.
 
						

							125
Move the zoom lever toward k.
zThe display will zoom in on the image. If 
you continue to hold the zoom lever, it will 
zoom in up to a maximum factor of 
approximately 10x.
zIf you press the opqr buttons, you can 
move the location of the displayed area.
zMove the zoom lever toward g to zoom 
out, or continue to hold it to return to single 
image playback.
zWhen   appears on the screen, press 
the m button to switch to  . Press 
the qr buttons to switch between images 
while zoomed. Press the m button again 
to return to the original setting.
Magnifying Images
Approximate Location of 
Displayed Area
•In magnified display, pressing the n button restores single image 
playback.
•Movies cannot be magnified.
 
						

							
126
Grouped images taken in   mode (p. 80) can also be viewed individually.
Choose an image group.
zPress the  qr buttons to choose an image 
that displays  .
Choose .
zAfter pressing the  m button, press the 
op  buttons to choose  , then press the 
m  button again.
View each image in the group.
zIf you press the  qr buttons only the 
images in the group will be displayed.
zAfter pressing the  m button, press the 
op  buttons to choose  , then press the 
m  button again to cancel group playback.
Viewing Each Image in a Group
Group playback
In group playback (Step 3 above), you c an use the FUNC. menu functions that 
appear when you press the  m button, as well as search  (p. 118) and magnify 
(p. 125)  images. You can process all the images in a group at once while 
performing operations in “Protecting Images”  (p. 134), “Erasing Images”  (p. 138), 
or “Choosing Images for Printing (DPOF)”  (p. 159), by choosing a set of grouped 
images.
 
						

							Viewing Each Image in a Group
127
Ungrouping Images
Grouped images taken in   mode can be ungrouped and viewed 
individually.
Choose [Group Images].
zPress the n button to choose [Group 
Images] from the 1 tab.
Choose a setting.
zPress the qr buttons to choose [Off].zPress the n button to complete the 
setting and restore single image playback.
XGrouped images taken in   mode are 
ungrouped and appear individually.
zTo regroup the images, follow the steps 
above and select [On].
Grouping cannot be canceled while viewing images individually (p. 126).
 
						

							128
The camera will choose four images based on the displayed image.
If you choose one of those images, the camera will select four more images
letting you enjoy playing back images in an unexpected order.
This will work best if you take many shots of various scenes.
Choose .
zAfter pressing the m button, press the 
op buttons to choose  , then press the 
m button again.
XFour images will appear as possibilities.
Choose an image.
zPress the opqr buttons to choose the 
image you want to view next.
XThe chosen image will be displayed in the 
middle, and the next four possibilities will 
appear.
zPress the m button to display the middle 
image at full size. Press the m button 
again to restore the original display. 
zPress the n button to restore single 
image playback.
Displaying Various Images (Smart Shuffle)
•Only still images shot with this camera will play back in Smart Shuffle.
• is not available in the following situations:
-If there are less than 50 images taken with this camera on the memory card
-If you play back images not supported by Smart Shuffle
-During filtered playback
 
						

							129
You can choose from 3 transition effects when switching between images in 
single image playback.
Choose [Transition].
zPress the n button to choose 
[Transition] from the 1 tab, then press the 
qr buttons to choose a transition effect.
Changing Image Transitions
 
						

							130
Viewing Images on a Standard TV
Using the supplied stereo AV cable (p. 2), you can connect the camera to a 
TV to view images you have shot.
Turn off the camera and TV.
Connect the camera to the TV.
zOpen the camera’s terminal cover and fully 
insert the cable plug into the camera’s 
terminal.
zInsert the cable plug fully into the video 
input terminals as shown in the illustration.
Turn on the TV and switch it to the 
input the cable is connected to.
Turn on the camera.
zPress the 1 button to turn on the camera.XThe image will appear on the TV (nothing 
will appear on the screen of the camera).
zAfter you finish, turn off the camera and 
TV, and unplug the cable.
Viewing Images on a TV
YellowWhite
White Yellow
RedRed
What if the images don’t display correctly on the TV?
Images will not display correctly if the camera’s video output setting (NTSC/PAL) 
does not match the TV system. Press the n button and choose [Video 
System] from the 3 tab to switch to the correct video system.