Candy Cdi10122 Manual

							Never use a spray cleaner to clean th e door panel fo r it could damage the doorlock and electrical components. Do not use abrasive
agents because of the risk of scratching or leaving spots on the stainless steel surfac e.
To clean the edge around the door, you should use only a soft warm, damp cloth. To prevent
penetration of water into the door lock and electrical components, do not use a spray cleaner
of any kind.
Also, never use abrasive cleaners or scouring pads on the outer surfaces because they will
scratch the finish. Some papers towels can also scratch or leave marks on thesurface.
Occasionally, items can get into the filter and drain pump. If this occurs,the drainpumps
fitted in your dishwashers are designed t o automatically revers e, ejecting the item back
into the sump area or down the drain. If you have to remove an obstacle from thedrain
pump, be fore you rem ove t he fi lters , you should t urn off the power; Then remove the small
black ins ert from the s ump area. (You m ight want to remov e any standing wa terfirst). Scoop
out the item that is probably in the sump area and causing the obstruction. Remember to
replace the bl ack insert before you put the filt ers back in.
After every wash, turn off the water supply to the
appliance and l eave the door slightly ajar so that
moisture and odors are not trapped inside.
Before cleaning or performing maintenance, always
remove the plug from the socket. Do not run risks.
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
To remove spots or stains from ,
use a cloth dampened with water and a little white
vinegar, or a cleaning product made specifically
for dishwashers. Instead, use a cloth with warm soapy water.
the interior surface
When you go on holiday, it is recommened that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming
within the appliance.
If the appliance must be moved, try to keep it in the vertical
position.If absolutely necessary, it can be positioned on
it s bac k.
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
9
3
step 3： lift the Fine filterup
To remove the filter follows steps 1-3, to insert the filter reverse the procedure.
NOTE： 
						

							Pull Unicouple and its hoses completely out from storage compartment located at rear of dishwasher
and attach it to the faucet adapter.
Turn water fully on before starting the dishwasher.
31
Turn off the water.
Rele ase the water pressure by depressing the press ure releas e button. This relieves water pressure and protects you, and the
room, from severe splashing.
Release Unicouple from faucet by depressing the collar at the top of the Unicouple connector.
321
Remove the power cord plug from the wall receptacle.
Disconnect Unicouple from faucet adapter.
21
If faucet has not threads: att ach the faucet ada pter t o faucet, then tighten every screw
of the adapter. To prevent leaking your should tighten the adapter.
2Attach the Unicouple conne ctor to the fauc et adapter by depressing the c ollaratthetopoftheconnector.
When Unicouple is all the way up onto the adapter, release the collar. It willthensnapIntopositionto
lock the Unicouple in place. The Unic ouple s small hose c arries water from the faucet to the dishwasher.
Its large hose carries drain water to the sink. Be sure Unicouple is pointing toward the sink bowl drain
openin g and the sink drain is open fo r water tha t will drain from your dis hwasher. I f your dishwasher
drains into a disposer, operate the disposer until it is completely empty before starting t he dis hwasher. '
Connector of ModelⅠ
A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is
recommended that the hose be disconnected and the hole plugged.
Fused electrical supply is required-copper wire only. Time delay fuse or circuit breaker recommended and provide separate
circuit s erving only this appliance. Outle t should be pla ced in adjacent cabinet.
Make sure that the plug on the appliance remains accessible after installation.
After making sure that the voltage and the frequency values for the currentin the home
correspond to those on the rating plate and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into an electrical socke t whic h is
earthed properly. If the electrical socket to which the appliance must be connected is not
appropriate for the , replace the socket ,rather than
using adaptors or the like as they could cause overheating and burns.plug (installed by a qualified electrician)
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
W ater pre ssure mu st be between 0,04 MPa and 1 MPa. If the p ressure is below theminimum
consult our Service Department for advice.
10 
						

							11
If the sink is 34 or higher from the floor, the excesswater in Unicouple hoses
cannot be drained directly into the sink. It will be necessary to drain excess
water from hoses into a bowl or suitable container that is heldoutside and lower
than the sink.
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is
fastened tightly in place.
If the wa ter pipes are new or hav e not been used for an ex tended period of time, let the water
runtomakesurethatthewaterisclearandfree ofimpurities.Ifthisprecaution is not taken,
there is a risk that the water inlet can get blocked and damage the appliance.
The water supply to the appliance can also be connected to the house hot waterline
(centralized system, heating system),as long as it does not exceed a temperature of 60 C.
In this case, the was h cyc le tim e will be shortene d by about 15 minutes a nd thewash
efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as those
for the connection to the cold water line.
DIMENSIONS(mm)
Con nector of Mode lⅡ
Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or letitrunintothesink,makingsuretoavoidbending
or crimping it. Use the special plastic support that comes with the appliance. The free end of the hose must be at a height
between 40 and 100cm and must not be immersed in water.
Once the appliance is positioned,adjust the feet (screwing them in or out)to adjust the
height of the dishwasher, making it level. In any case ,the appliance should not be inclined
mo r e t han 2 .
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent
cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to
facilitate proper installation.
600 600
850
1155 
						

							Fuse blown, or the
circuit breaker actedReplace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Sound from Soft food shredding action and detergent cup
ope ning.
Utensils are not secure
in the baskets or something
sm all h as droppe d into
the bas ketEns ure ev erything is sec ured in the dishwasher.
Motor hums Dishwasher has not been used regularly. If you do not use it
often, remember to set it to fill and pump out every week,
which will help keep the seal moist.
Improper detergent
Add 1 ga llon of cold wat er to the tub. Close and latch the
dishwasher, then drain out the water by slowly turning the
Dial until a drain period is reached. Repeat if necessary.
Spilled rinse agent Always wipe up rinse agent
spills immediately.
Detergent with
colorant was usedMa ke sure that the deter gent is the one without colorant.
R inse agent dispenser
is emptyMake sure that the rinse agent dispense is filled.
Improper programme
Impro per b asket loading Ma ke sure that the action of the de terge nt dis penser and
spray arms are not bloc ked by large dis hware.
Extremely hard water
Low inlet
temperature
Overloading the
dishwasher
Improper loading
Old or damp powder
detergent
Empty rinse agent
dispenser
In correct do sage of
detergentTo remove spots from glassware:
Take out all metal utensils out of the dishwasher.
Do not add detergent.
C hoose the longest cycle.
Start the dishwasher and allow it to run for about
18 to 22 minutes, then it will be in the main wash.
Open the door to pour 2 cups of white vinegar
into the bottom of the dishwasher.
C lose the do or an d let the dishwa sher complete
the cycle. If the vinegar does not work: Repeat
as above, except use 1/4 cup (60 ml)of citric acid
cr ystals instead of vine gar.
Some audible sounds are
normal
'
Make sure the dishwashe r is turned on a nd the door is
closed securely.
Check that the water supply is connected properly and
the water is turned on.
Make sure the power cord is properly plugged into the
wall socket. Power supply is not
turned on
Water pressure is low
'Overflow
The system is designed to detect an overflow. When it
does, it shuts off the circulation pump and turns on the
drain pump.
Sel e ct s t ro ng e r pr o g ram me
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
12 
						

							Combination of soft
water and too much
detergentUse less detergent if you have soft water and select a
shorter cycle to wash the gl assware.
Tea or coffee stains Use a solution of 1/2 cup of bleach and 3 cups warm water
to remove th e stains by hand.
You have to wait for 20 minutes after a cycle to let the heating
elements cool down before cleaning interior; otherwise, burns
will happen.
Iron deposits in wate r
can c ause an overall filmYou have to call y our water utility company
Hard water minerals To clean the interior, use a damp sponge with dishwasher
detergent and wear rubber gloves. Nev er use any other cleaner
than dishwasher detergent for the risk of foaming or suds.
Dial is not in the
positionOFFTurn the Dial toOFF position and slide the door latch to the
left.
Dishes block detergent
cupsRe-loading the dishes properly.
This is normal
There is some steam coming through the vent by the door
latch during drying and water draining.
Aluminum utensils have
rubbed against dishesUse a mild abrasive cleaner to eliminate those marks.
'
This is normal A small amount of clean water around the outlet on
the tub bottom at the back of the tub keeps the water
seal lubrica ted.
B e careful n ot to overf ill the rins e aid dispenser.
Spilled rinse aid could cause oversudsing and lead
to overflowing. Wipe away any spills with a damp cloth.
Make sure the dishwasher is level. Ove rfill dispenser or rinse
aid spills
Dishwasher isn t level'
13
Longer inlet time.Faucets is not opened.
Longer heating time,
but not reaching required temperatureMalfunction of temperature sensor or of heating element.
Overfilled.Too much inlet water. .
Failure of temperature sensorShort circuit or break of temperature sensorOpen circuit or break of temperature sensor
Failure of temperature sensor