Candy Cdcp 6e Manual

							7
Amount of Detergent to Use
Push latch to open
12
Based on their chemical composition, dishwasher can be split in two basic types:
Detergent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve and develop their full cleaning power during short
programmes. Therefore please use long programmes when using detergent tablets, to
ensure the complete removal of detergent residuals.
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the Wash Cycle Table . Your dishwasher uses less detergent and rinse aid then
conventional dishwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. Also, more heavily soiled items need more detergent. Always add the
detergent just before starting the dishwasher, otherwise it could get damp and will not
dissolve properly.
Concentrated Detergent
Detergent Tablets
Detergent Dispenser
Always add the detergent just before starting each wash cycle.
Only use branded detergent aid for dishwasher. If the lid is closed: press release button. The lid springs open.
conventional, alkaline detergents with caustic components
low alkaline concentrated detergents with natural enzymes
Normally new pulverised detergent is without phosphate. The water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardness of water is only 6 dH. If detergents without phosphate were used in case of hard water
often white spots appear at dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strong and coloured  spots will not
removed completely. In this case please choose a programme with higher Temperature.
NOTE:
Detergent tablet Detergent powder
NOTE:Detergent tablets are only for the models with 3 in 1 function or 3 in 1 program. 
						

							8 Fill the detergent dispenser with detergent.
The marking indicates the dosing levels , as
illustrated on right:
The place of main wash cycle detergent placed.
The place of pre-wash cycle detergent placed.
Please observe the manufacturers dosing and storage
Recommendations as stated on the detergent packaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional
detergent dose in the pre-wash detergent  chamber. This detergent will take effect during the pre-wash phase.
A
B
Fill in detergent
You find information about the amount of detergent for the single programme on the  last page.
Please aware, that according to the level soiling and the specific hardness of  water differences are possible.
Please observe the manufacturer's recommendations on the detergent packaging.
NOTE:
AB
5.Loading the Dishwasher Baskets
For washing in the dishwasher the following cutlery/dishes
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not
Older cutlery with glued parts that is not
temperature resistant
Bonded cutlery items or dishes
Pewter or items
crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibresheat resistant
copperSome types of glasses can become
dull after a large number of washes
Silver and aluminium parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
Are not suitable
Are of limited suitability
Don't put powder detergent into the dispenser until you're ready to wash dishes. Use only detergent specifically made for use in dishwashers. Keep your detergent fresh and dry. Proper Use of Detergent
Recommendation
Use a mild detergent that is described as 'kind of dishes'. If necessary, seek further
information from detergent manufacturers.
For particular items, select a programme with as low a temperature.
To prevent damage, do not take glass and cutlery out of the dishwasher immediately
after the programme has ended. Consider buying utensils which are identified as dishwasher-proof.
WARNING!
Dishwasher detergent is corrosive! 
Take care to keep it out of reach of children. 
						

							Position the dishes and cookware so that they will not get moved by the spray of water.
LLoading the Basket
9 Dishes and items of cutlery must not lie inside one another, or cover each other.
To avoid damage to glasses, they must not touch.
Load large items which are most difficult to clean into the basket.
Long bladed knives stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knives must be positioned
horizontally in the basket.
Please do not overload your dishwasher. This is important for good results and for
reasonable energy consume. Load hollow items such as cups, glasses, pans etc. With the opening downwards so that
water cannot collect in the container or a deep base.
(For best performance of the dishwasher, follow these loading guidelines.
Features and appearance of baskets and cutlery baskets may vary from your model.)
Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots/pans, etc. are face down.
2.Curved items, or those with recesses, should be loaded at a slant so that water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are placed in the way that the spray arms can rotated freely during washing.
NOTE:Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
Attention before or after loading the Dishwasher Baskets
Saucers4
Medium serving bowl
3
Glasses
1
Cups
6
Oval platter
7
Dinner plates
8
Soup plates
Dessert dishes
9
Dish
5
Cutlery basket
10
2
1
63
11
7 8
49 5
2
IN
Serving spoons
1110 
						

							10
Position the dishes and cookware so that they do not get moved by the spray of water.
Cutlery Basket
IN
Do not let any item extend through bottom.
Always load sharp utensils with the sharp point down!
WARNING!
For personal safety and a top quality clean, make sure place the silverware in the basket as follows:
They do not nest together.
Place silverware with handles-down.
But place knives and other potentially d
angerous utensils handles-up.
Teaspoons4
Soup spoons2
Forks1
Serving forks8
Serving spoons6
Knives53
Dessert spoons
7Gravy ladles
7
1
3
4
31
41
4
3
1
6
3
4
4
3 14
3
1
8 
						

							6.Starting a washing programme
Wash CycleTable
11
NOTE:
Turning On theAppliance
Starting a wash cycle...
Draw out the basket(see the section entitled Loading the Dishwasher ).
Pour in the detergent (see the section entitled Salt,
Detergent and Rinse Aid ).
Insert the plug into the socket. The power supply is 220-240
VAC 50 HZ, the specification of the socket is 10 A 250 VAC.
Make sure that the water supply is turned on to full pressure.“”
“
”
Press the program button , the wash program will be changed  as follows direction
If  a program is selected, the response light will light. Then press the
button, the  dishwasher begins to start.
Start/Pause
When you press the button to pause during washing,
the program light will stop blinking and the dishwasher will mooing
every minute unless you press the button to start.Start/Pause
Start/Pause
NOTE:
*EN 50242 : This programme is the test cycle. The information for comparability test
in accordance with EN 50242, as follows:
Capacity: 6 setting
The power consumption of off-mode is 0.45W
left-on mode is 0.45W Rinse aid setting: 6
Detergent
pre/main Cycle Selection
Information ProgramRunning
time(min)Energy
(Kwh)Water
(l) Description
of CycleRinse
Aid
For normally soiled loads,
such as pots, plates,
glasses and lightly
soiled pans.
For heaviest soiled crockery,
and normally soiled pots
pans dishes etc with dried
on soiling.、
、
A shorter wash for lightly soiled
loads and quick wash.
For lightly soiled crockery
and glass.
15g120
195
140
30 900.7
0.610.9
0.23 0.658
6.510
6 7.0
Pre-wash
Wash (60 )
Rinse
Rinse (70 )
Drying℃
℃
Pre-wash
Wash (50 )
Rinse
Rinse (70 )
Drying℃
℃
Wash(65 )
Rinse(70 )℃
℃
Drying
Wash (40 )
Rinse℃
Rinse (40 )℃
Intensive
Pre-wash 50
Wash (70 )
Rinse
Rinse
Rinse (70 )
Drying℃
℃
℃ ()
 Daily
Rapid
Normal
(*EN 50242)
This is standard programme,
it is suitable to clean normally
soiled tableware and it is the
most efficient programme in
terms of its combined energy
and water consumption for
that type of tableware.
Wash (45 )
Rinse
Rinse (60 )
Drying℃
℃For lightly soiled loads,
such as glasses, crystal and
fine china.
75
0.5 7.0Glass
(or )3in1
18g (or )3in1
18g (or )3in1
3/15g (or )3in1
3/15g (or )3in1
3/15g
ECO->Glass->        ->Rapid->Intensive->Normal Daily 
						

							12
When the working cycle has finished, the buzzer of dishwasher will sound 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
1.Switch off the dishwasher by pressing the ON/OFF button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Change the Programme...
Forget to Add a Dish?
Forget toAdd a Dish?
will keep on working after 10  seconds.
If you open the door when washing, the machine will pause. When you close the door , the machineNOTE:
A t t h e e n d o f t h e Wa s h C y c l eAt the end of the Wash Cycle
A forgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door
After the spray arms stop working,you can open the door
completely.
2
3
Open the door a little to stop the washing.
14
5
6
Premise:
Otherwise, the detergent may have already been
released, and the appliance may have already drained the wash water. If this
is the case, the detergent dispenser must be refilled (see the  section entitled
" Loading the Detergent " ).
NOTE: If you open the door during  washing, the machine will pause. When you
close the door and press the Button, the machine will keep on
working after 10 seconds.
The  program lights show  the state of the dishwasher:
Press S Button to pause the machine when the door is closed ,Press
Button more than  three  seconds the machine will be in stand by state ,
then you can change  the program  to the  desired cycle  setting (see the section
entitled  " Starting a wash cycle. . ." ).
S
a) One of the program lights on----------stand by or pause
b) One of the program lights blinking-----  run
You can modify  the washing program, When the dishwasher  just
r u n s  f o r a s h o r t t i m e .
tart/Pause
tart/Pause Program
Press the buttontart/Pause S
Press the button, the dishwasher will run
after 10 seconds.tart/Pause S
WARNING!
It is dangerous to open the door when washing,
because the hot water may  scald  you.
If your model has broken remember function, the machine will go on to finish  the selected
program after the power cut. 
						

							77.Maintenance and Cleaning
The filter prevent larger remnants of food or other objects from getting inside the pump.
The filter system consists of a coarse filter, a flat  (Main filter)
and a micro filter (fine filter).
Food and soil particles trapped by this filter are pulverized by a
special jet on the spray arm and washed down to drain.
Main filterA
Larger items, such as pieces of bone or glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by this filter, gently squeeze the tap on the top of this
filter and lift it out.
Coarse filterC
This filter holds soil and food residues in the sump area and
prevents it from being redeposited on the dishes during a cycle.
Fine filterB
Filtering System
Filter assembly
The filter efficiently
For best performance and results, the filter assembly must be cleaned regularly. this reason, it is a good idea to
remove the larger food particles trapping in the filter after each wash cycle by rinsing the filter and cup under
running water. To remove the filter assembly, pull the cup handle in the upward direction.removes food particles from the wash water, allowing it to be recycled during the cycle.
For
WARNING!
Never run the dishwasher without the filters in place.
The dishwasher must never be used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
the filter system will be installed.
If do it from step1 to step 3, the filter system will be removed; while if do it from Step 3 to Step 1,NOTE:
13
Step 1 Contrarotate thefilter assembly(A,B and C),
then lift it all up.：
Open
C
B
A
Step 2:   Lift B and C up from A;
A
B
C
A
B C
Step 3:   Separate B and C. 
						

							The control panel can be cleaned by using a lightly dampened cloth. After cleaning,make sure to dry it thoroughly.
For the exterior use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Protect Against Freezing
1. Cut off electrical power to the dishwasher.
2. Turn off the water supply and disconnect the water inlet pipe from the water valve.
3. Drain water from the inlet pipe and water valve (Use a pan to catch the water)
4. Reconnect the water inlet pipe to the water valve.
5. Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump. please take frost protection measures on the dishwasher in winter. E fter washing cycles,
please operate as followsa c h t i m e a
：
CCaring for the Dishwasher
- Inspect the filters for blocking after every time the dishwasher has been used.
- By unscrewing the coarse filter, you can remove the filter system.Remove any food remnants and
clean the filters under running water.
Notes:
Cleaning The Filter
Cleaning The Door
To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures
on the last page and reinsert the entire assembly in the dishwasher, positioning in its seat and pressing downward.
The entire filter assembly should be cleaned once a week.
When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted and the performance of dishwasher could be decreased.WARNING!
NOTE:
To clean the edge around the door, you should use only a soft warm,
damp cloth. To avoid penetration of water into the door lock and
electrical components, do not use a spray cleaner of any kind.
WARNING!
Never use a spray cleaner to clean the door panel as it may damage the door lock
and electrical components.
Abrasive agents or some paper towel should not be used because of the risk of
scratching or leaving spots on the stainless steel surface.
 

14
NOTE:If your dishwasher cannot work because of the ice, please contact authorised service person. 
						

							How to Keep Your Dishwasher in Shape
It is recommend that you run a wash cycle with the
dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
seals to last longer and prevent odours from forming
within the appliance.
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
8.Installation instruction
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odors are not trapped inside.
Before cleaning or performing maintenance, always
remove the plug from the socket.
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Only use a cloth with warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water with a little
vinegar, or a cleaning product made specifically for
dishwashers.
After Every Wash
Remove the Plug
No Solvents or Abrasive Cleaning
Moving the Appliance
Seals
When not in use for a long time
15
The installation of the pipes
and electrical equipments
should be done by qualified
professionals.
Warning
Electrical Shock Hazard
Disconnect electrical power
before installing dishwasher.
Failure to do so can result in
death or electrical shock.Attention:
The installation position of dishwasher should be near the existing water inlet tap and drain
outlet and power socket.
One side of the cabinet sink should be chosen to facilitate the connection of drain
hoses of the dishwasher.
Installation preparation
Cleaning the Spray Arms
The spray arms can be easily removed for periodic cleaning
of the nozzles to prevent possible clogging. Wash them
under running water and carefully replace them in their seats,
checking that their rotary movement is in no way impeded.
Grasp the middle of the spray arm, pull it upwards to remove
it. Wash the arms under a jet of running water and replace it
carefully to its seat. After reassembly, check that the spray
arms rotate freely. Otherwise, check that they have been
installed correctly. 
						

							16
Electrical Requirements
Ensure the voltage and frequency of the power being corresponds to
those on the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug , replace the socket, rather than using a adaptors or the like as
they could cause overheating and burns.
Electrical Connection
Insure proper ground
exists before use
Please look at the rating label  to know the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and provide separate circuit serving
only this appliance.
Positioning theAppliance
and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply Position the appliance in the desired location. The back should rest against the wall behind it,
and drain hoses that can be positioned to the right or the left to facilitate proper installation.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure
that it is fastened tightly in place. If the water pipes are new or have not been used for
an extended period of time, let the water run to make sure that the water is clear and
free of impurities. If this precaution is not taken, there is a risk that the water inlet can
get blocked and damage the appliance.
please close the hydrant after using.WARNING!
Water Connection
About Power Connection


 

Please Note: If the supplied hose cloes not fit your tap, please contact your local
plumbing supply center where adapters are available for purchase.
For personal safety:
Do not use an extension cord or an  adapter plug 
with this appliance.
Do not, under any circumstances, cut or remove  the 
earthing 
Connection from the power cord.           WARNING!
          WARNING!