Home > Brother > Software > Brother Pe Design 7 Manual

Brother Pe Design 7 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Brother Pe Design 7 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							315
    Tutorial (Advanced)
    To display information for the other design 
    sections in the emboroidery, click on Next and 
    Previous to move back and forth through 
    each section.
    Check the design, and then click Close.
    Step 4Saving the design
    Once the embroidery design is finished, you may 
    want to save it in order to retrieve it later.
    Click File, then Save.
    Select the drive and the folder, and then type 
    in the file name.
    Click Save.
    aNote:
    Before an embroidery pattern created in a 
    custom Design Page is saved or transferred 
    to an original card, running stitches are 
    added at the edges of the design sections so 
    that the design sections can easily be 
    aligned during sewing. This alignment 
    stitching appears in the 
    NOT DEFINED color 
    and cannot be edited. (For more details, 
    refer to “Embroidering” on page 191.)
    aNote:
    If a section of the design exceeds the 
    maximum allowed for the stitch count or 
    number of colors, a message appears, 
    describing the limitations and asking 
    whether or not the pattern should be saved 
    anyway. If the embroidery pattern extends 
    off the Design Page, a message appears, 
    asking whether or not the pattern should be 
    saved anyway. If the design is saved 
    anyway, it must be edited before it will be 
    sewn. 
    						
    							316
    Tutorial (Advanced)
    Step 5Transferring the design to an 
    original card
    By writing a design to a media that can be used in 
    your embroidery machine and transferring it to 
    your embroidery machine, you can actually sew 
    the design. For this example, we will transfer the 
    design to an original card.
    Insert an original card into the USB card
    writer module.
    Transfer the embroidery design.
    Click File, then Write to Card.
    →The following message appears.Click OK.
    →The following message appears.
    Click OK.
    Quit Layout & Editing.
    Click File, then Exit.
    bMemo:
    For other media you may use include floppy 
    disks, compact flash memory, USB media and 
    etc.
    aNote:
    The original card is inserted correctly when 
    you hear it snap into place.
    1
    2
    aNote:
    Before using the original card, make sure 
    that the designs on the card are no longer 
    needed or make sure to store them on your 
    hard drive or other storage media.
    aNote:
     If the card writer module is not correctly 
    connected or powered, an error message 
    of “No card writer module is connected. 
    Please connect card writer module.” will 
    appear.
     If the original card is not inserted or is 
    defective, an error message of “No 
    original card is inserted. Please insert an 
    original card.” will appear.
    3 
    						
    							317
    Tips and Techniques
    Sew Types
    The sewing attributes for each sew type are first set to their default settings; however, by changing the settings 
    of the sewing attributes, you can create custom stitching.
    cFor more details, refer to “Line sewing attributes” on page 153 (Layout & Editing).
    cFor more details, refer to “Line sewing attributes” on page 218 (Design Center).
    cFor more details, refer to “Region sewing attributes” on page 155 (Layout & Editing).
    cFor more details, refer to “Region sewing attributes” on page 219 (Design Center).
    Line sew types
    Zigzag Stitch Running Stitch/Triple Stitch
    Motif Stitch E/V Stitch
    Region sew types
    Satin Stitch Fill Stitch
    Programmable Fill Stitch Motif Stitch 
    						
    							318
    Tips and Techniques
    Cross Stitch Concentric Circle Stitch
    Radial Stitch Spiral Stitch
    Piping Stitch Piping Stitch (motif setting) 
    Random Walking Stitch
    cFor more details, refer to “Programmable fill stitch” on page 157 (Layout & Editing).
    cFor more details, refer to “Programmable fill stitch” on page 221 (Design Center).
    cFor more details, refer to “Motif stitch” on page 154 in “Line sewing attributes” (Layout & Editing).
    cFor more details, refer to “Motif stitch” on page 159 in “Region sewing attributes” (Layout & Editing).
    cFor more details, refer to “Motif stitch” on page 223 in “Region sewing attributes” (Design Center).
    bMemo:
    The stitching for the programmable fill stitch and the motif stitch depends on the selected stitch pattern. 
    						
    							319
    Tips and Techniques
    Enlarging/Reducing Embroidery Patterns
    There are several ways of enlarging or reducing an imported embroidery pattern in Layout & Editing. You may 
    choose to scale your pattern with the pointer, or apply the Stitch to Block function, then scale the pattern.
    When you normally scale an imported pattern, the number of stitches that will be sewn remains the same, 
    resulting in a change of embroidery quality if the size of the pattern is greatly changed. However, by holding 
    down the   key while scaling the imported embroidery pattern, the original embroidery quality can be 
    maintained, since the stitch density and fill pattern automatically adapts to the new size.
    Another method of maintaining the original embroidery quality of the pattern is to select the Sew – Stitch to 
    Block command, then scale the pattern. When a pattern is scaled only moderately, it may not be necessary 
    to apply the Stitch to Block function.
    Sewing Direction
    In order to limit shrinking, select a stitch direction perpendicular to the larger edge of the area. 
    Sewing Order
    After creating an embroidery pattern made of several different parts (in Layout & Editing or Design Center), be 
    sure to check the sewing order and correct it if necessary.
    With Layout & Editing, the default sewing order is the order in which the elements are drawn.
    With Design Center, the default sewing order is the order in which the sewing attributes are applied.
    Sewing Wide Areas
    For best sewing results, set Under sewing to On when sewing wide regions.
    cFor more details, refer to “Under sewing” on page 153.
    Changing the Sewing Direction setting prevents shrinkage of the stitching.
    Affixing stabilizer material to the back of the fabric prevents shrinkage of the stitching and misaligned 
    patterns. This system allows you to create a wide variety of embroidery patterns and supports wider ranges for the 
    setting of the sewing attributes (thread density, sewing pitch, etc.). However, the final result also depends 
    on your particular embroidery machine model. We recommend that you make a trial sewing sample with 
    your sewing data before sewing on the final material. Remember to sew your trial sample on the same 
    type of fabric as your final material and to use the same needle and the same machine embroidery thread.
    Ctrl
    Shrinking more likely to occur Shrinking less likely to occur 
    						
    							320
    Tips and Techniques
    When satin stitching is sewn in a wide area, the stitched area may shrink after sewing, depending on the 
    material and the type of thread used. If this happens, switch to this alternate method: Select the fill stitch 
    and use stabilizer material on the reverse side of the fabric.
    Tips for Importing Images for Design 
    Center
    Refer to the following when importing images for Design Center.
    When scanning illustrations
    If the outline is not clear, trace the outline on tracing paper.
    Better scanning results may be produced by reducing the tone of the image.
    Patter n
    After sewing
    aNote:
    When using the satin stitch in a wide area, the needle may move out of position by about 10 mm with some 
    machines. In order to avoid this, use the above-mentioned alternate method. 
    						
    							321
    Tips and Techniques
    Removing Sections of Stitch Pattern 
    (by Using the Split Stitch tool)
    Click   on the Tool Box in Layout & Editing, click a frame around the desired section of the stitch pattern, 
    and then double-click to remove the framed section.
    cFor more details, refer to “Splitting off parts of a stitch pattern” on page 116.
    Creating Beautiful Photo Embroidery
    For Photo Stitch
    Select a photograph that shows a large 
    image. (A photograph with an intricate 
    image, for example, one that contains many 
    objects, is not suitable.)
    Increase the contrast.
    An image with a width and height between 
    300 and 500 dots is suitable.
    For best results with human portraits, the 
    main focus of the image should be the area 
    between the chest and the top of the head 
    and the image should be framed in an area 
    of 130 × 180 mm (5 × 7 inches) or more.
    For best results when using a dark original image, we recommend setting Brightness in the Photo Stitch 
    Parameters dialog box to a higher setting.
    If the created embroidery pattern contains colors that you do not wish to emphasize (for example, grays in 
    the face), change the sewing order in the Sewing Order/Color dialog box so that the undesirable color is 
    sewn before all other colors.
    cFor more details, refer to “Changing colors of a stitch pattern” on page 115.
    To create sepia photo embroidery, first create a sepia user thread chart in the Edit User Thread Chart 
    dialog box, and then select the created sepia user thread chart under Color Option in the Photo Stitch 
    Parameters dialog box.
    at 100 mm × 100 mm
    at 130 mm × 180 mm 
    						
    							322
    Tips and Techniques
    cFor more details, refer to “Editing User Thread Color Lists” on page 162.
    Fonts Suitable for Embroidering
    When sewing small fonts
    For best results when embroidering designs 
    containing small font patterns, follow the 
    recommendations described below.
    1.Reduce the thread tension to less than what is 
    used when embroidering normal designs.
    2.Sew at a speed slower than what is used when 
    embroidering normal designs.
    (For details on adjusting the thread tension 
    and sewing speed, refer to the Instruction 
    Manual provided with your embroidery 
    machine.)
    3.For best results when sewing small font 
    patterns, do not cut the jump stitches between 
    the characters.
    (For details on setting the machine for thread 
    cutting, refer to the Instruction Manual for the 
    embroidery machine.)
    When converting TrueType fonts 
    to embroidery patterns
    For best results when converting TrueType fonts to 
    embroidery patterns, select a font where all lines are 
    as thick as possible, such as with a Gothic font. 
    						
    							323
    Tips and Techniques
    Creating Outlined Characters (Using Text 
    Converted to Outline Object)
    Outlined characters within a shape can be created by applying the Convert to Outline Object command to a 
    character of a TrueType font.
    1.Use a Shape tool to draw a shape.
    cFor more details, refer to “Drawing 
    Shapes” on page 118.
    2.Select a character in a TrueType font.
    3.Right-click the character, and then select 
    Convert to Outline Object from the menu 
    that appeared.
    cFor more details, refer to “Converting text 
    to outline pattern” on page 138.
    4.Position the character so that it is framed by 
    the shape.
    5.After selecting the outlined character pattern, 
    hold down the Ctrl key and select a Shape tool 
    to select Set Hole Sewing.
    cFor more details, refer to “Preventing 
    overlapping stitching (hole sewing)” on 
    page 166.
    6.Select the outlined pattern inside the 
    character, and then click the Region sew 
    button .
    (Since the background color in this example is 
    black, the color selected with the Region 
    color button   is black.)
    →The outlined character is completed. 
    						
    							324
    Tips and Techniques
    Converting Characters (Japanese, Chinese, 
    Korean, etc) to Embroidery Patterns
    Embroidery patterns can be created from various characters, such as Japanese, Chinese, Korean etc, using 
    TrueType fonts.
    For this example, we will create an embroidery pattern from Japanese characters.
    1.Select a Text tool, and then select a Japanese 
    TrueType font (for example, “MS Gothic”).
    2.Click in the Design Page where you want to 
    enter the text. The Edit Text Letters dialog 
    box appears.
    3.Display a character code table different from 
    the one that appeared in step 2. (Start – All 
    Programs – Accessories – System Tools – 
    Character Map)
    4.Select MS Gothic from the Font list in 
    Character Map, and then select the 
    Advanced view check box. Next, select 
    Windows: Japanese from the Character set 
    list, select the desired character, and then 
    click Select.
    (This example shows the Japanese hiragana 
    for the word meaning “Good Afternoon”.)
    5.After selecting all of the desired characters, 
    click Copy to copy the characters.
    6.Paste the characters into the Edit Text 
    Letters dialog box in Layout & Editing, and 
    then click OK.
    bMemo:
     The following procedure describes how to 
    install Japanese, Chinese and Korean fonts 
    on the English operating system for 
    Windows
    ® XP.
    1) Click Start, select Control Panel, and 
    then click Date, Time, Language, 
    and Regional Options.
    2) Click Regional and Language 
    Options
    , and then click the Language 
    tab.
    3) Select the Install files for East Asian 
    languages check box under 
    Supplemental language support, 
    and then click OK.
    4) Complete the Windows
    ® installation 
    by following the instructions that 
    appear.
     If Japanese or Korean can be entered 
    directly from the computer keyboard, those 
    characters can be entered directly into the 
    Edit Text Letters dialog box. 
    						
    All Brother manuals Comments (0)

    Related Manuals for Brother Pe Design 7 Manual