Brother Mfc 7360 N Manual

Loading paper
11
2
bWhile pressing the green paper-guide 
release lever, slide the paper guides to 
fit the paper size you are loading in the 
tray. Make sure that the guides are 
firmly in the slots.
 
cFan the stack of paper well to avoid 
paper jams and misfeeds.
 
dPut paper in the tray and make sure:
The paper is below the maximum 
paper mark (b b b) (1).
Overfilling the paper tray will cause 
paper jams.
The side to be printed on must be 
face down.
The paper guides touch the sides of 
the paper...

Chapter 2
12
fUnfold the support flap (1) to prevent 
paper from sliding off the face-down 
output tray.
 
Loading paper in the manual 
feed slot2
You can load envelopes and special print 
media one at a time into this slot. Use the 
manual feed slot to print or copy on labels, 
envelopes or thicker paper.
Note
The machine automatically turns on the 
Manual Feed mode when you put paper in 
the manual feed slot.
 
Printing on plain paper, thin paper or 
recycled paper from the manual feed 
slot
2
aUnfold...

Loading paper
13
2
cUsing both hands, slide the manual feed 
slot paper guides to the width of the 
paper that you are going to use.
 
dUsing both hands, put one sheet of 
paper in the manual feed slot until the 
front edge of the paper touches the 
paper feed roller. When you feel the 
machine pull in the paper, let go.
 
Printing on thick paper, bond paper, 
labels and envelopes
2
When the back output tray is pulled down, the 
machine has a straight paper path from the 
manual feed slot through to the...

Chapter 2
14
Note
 
Pull down the two green levers, one on the 
left-hand side and one on the right-hand 
side, as shown in the following illustration.
 
 
bOpen the manual feed slot cover. 
cUsing both hands, slide the manual feed 
slot paper guides to the width of the 
paper that you are going to use.
 
dUsing both hands, put one sheet of 
paper or one envelope in the manual 
feed slot until the front edge of the paper 
or envelope touches the paper feed 
roller. When you feel the machine pull in 
the...

Loading paper
15
2
 
Note
• Put the paper into the manual feed slot 
with the side to be printed face up.
• Make sure that the print media is straight 
and in the correct position on the manual 
feed slot. If it is not, the paper may not be 
fed properly, resulting in a skewed printout 
or a paper jam.
• Do not put more than one sheet of paper 
in the manual feed slot at any one time, as 
it may cause a jam.
• If you put any print media in the manual 
feed slot before the machine is in Ready 
mode, the...

Chapter 2
16
Unscannable and unprintable areas2
The figures below show maximum unscannable and unprintable areas. The unscannable and 
unprintable areas may vary depending on the paper size or settings in the application you are 
using.
 Usage Document 
SizeTop (1)
Bottom (1)Left (2)
Right (2)
Fax (Send) Letter 3 mm 4 mm
A4 3 mm 3 mm
Copy
*a single copy 
or a 1 in 1 copyLetter 3 mm 4 mm
A4 3 mm 3 mm
Scan Letter 3 mm 3 mm
A4 3 mm 3 mm
Print Letter 4 mm 6.35 mm
A4 4mm 6.35mm
2
2
1
1 

Loading paper
17
2
Paper settings2
Paper Type2
Set up the machine for the type of paper you 
are using. This will give you the best print 
quality.
aPress Menu, 1, 2, 1.
bPress a or b to choose Thin, Plain, 
Thick, Thicker, Recycled Paper or 
Label.
Press OK.
cPress Stop/Exit.
Paper Size2
You can use several different sizes of paper 
for printing copies: A4, Letter, Legal, 
Executive, A5, A5 L, A6, B5, B6 and Folio and 
for printing faxes: A4, Letter, Legal or Folio 
(215.9 mm  330.2 mm).
When you...

Chapter 2
18
Type and size of paper2
The machine loads paper from the installed 
standard paper tray or manual feed slot.
The name for the paper trays in the 
printer driver in this Guide are as 
follows:
2
Paper capacity of the paper trays2
1Folio size is 215.9 mm  330.2 mm.
2Legal or Folio size paper are not available in some regions.
Recommended paper specifications2
The following paper specifications are suitable for this machine.
Use paper made for plain paper copying.
Use paper that is 75 to 90...

Loading paper
19
2 Handling and using special 
paper2
The machine is designed to work well with 
most types of xerographic and bond paper. 
However, some paper variables may have an 
effect on print quality or handling reliability. 
Always test samples of paper before 
purchasing to ensure desirable performance. 
Store paper in its original packaging and keep 
it sealed. Keep the paper flat and away from 
moisture, direct sunlight and heat.
Some important guidelines when selecting 
paper are:
DO NOT use...

Chapter 2
20
Envelopes2
Most envelopes designed for laser printers 
will be suitable for your machine. However, 
some envelopes may have feed and print-
quality problems because of the way they 
have been made. A suitable envelope should 
have edges with straight, well-creased folds 
and the leading edge should not be thicker 
than two sheets of paper. The envelope 
should lie flat and not be of baggy or flimsy 
construction. You should buy quality 
envelopes from a supplier who understands 
that you...