Brother Laserprinter Hl 1650 1670n User Guide

CHAPTER 3 CONTROL PANEL
3-31
™ INTERFACE
 
 
 Setting Menu Description
 AUTO IF TIME 
= 1:5:99 (sec)
 
You must set the timeout period for the auto interface selection.
 INPUT BUFFER 
= Level1:5:15
 
Increase or decrease the
input buffer capacity. 
RESTART PRINTER?
 
 
When using the parallel interface
 Sub-setting Menu Description
 HIGH SPEED 
=ON/OFF
 
Turns the high speed parallel communications
ON/OFF.
 PARALLEL
 BI-DIR=ON/OFF 
=ON/OFF
 
Turns the bi-directional parallel communications
ON/OFF. 

USER’S GUIDE
3-32
™  RESET MENU
 
 
 Setting Menu Description
 RESET PRINTER 
Resets the printer and restores all printer settings – including command
settings – to settings you have previously made with the control panel switches.
 FACTORY RESET 
Resets the printer and restores all printer settings – including command
settings – to the factory settings. See “List of Factory Settings”.
  

CHAPTER 3 CONTROL PANEL
3-33
 
™  Set IP Address
 
 
INFORMATION
↓Press the +
 or –
 switch to select the “NETWORK” menu.
NETWORK
↓Press the Set switch.
TCP/IP
↓Press the Set switch.
TCP/IP ENABLE
↓Press the + switch.
IP ADDRESS=
↓Press the Set switch.
192.0.0.192     ✲
↓
The last number in the digit which you can change is blinking.
Press the
 + or – switch to increase or decrease the number.
Press the 
Set switch to go to next digit.
123.0.0.192
↓Repeat this until you have set your IP address....

USER’S GUIDE
3-34
 
™ About Emulation Modes
This printer has the following emulation modes.
♦ HP LaserJet Mode
 
 
The HP LaserJet mode (or HP mode) is the emulation mode in which this
printer emulates the Hewlett-Packard LaserJet laser printer. Many software
applications support this type of laser printer. Using this mode will allow your
printer to operate at its optimum performance with those applications.
 
 
 
♦ BR-Script 3 Mode
BR-Script is an original page description language and a PostScript...

CHAPTER 3 CONTROL PANEL
3-35
♦ EPSON FX-850 and IBM Proprinter XL Mode
The EPSON FX-850 and IBM Proprinter XL modes are the emulation modes
that this printer emulates to meet the industry-standard for dot matrix
printers of their respective manufacturers. Some applications support these
dot matrix printer emulations. Use these emulation modes for optimum
performance when printing from those types of applications. 

USER’S GUIDE
3-36
™ List of Factory settings
The following table shows the initial factory default settings.
 Note
•The settings are subject to the emulation mode. Effective modes are
indicated in parentheses in the following table.
•The following settings cannot be restored to the factory settings with the
RESET menu in the “FACTORY SETTINGS” mode: INTERFACE MODE,
HRC SETTING, PAGE PROTECTION, SCALABLE FONT, LOCK
PANEL, PAGE COUNTER and local language for display messages.
•The COPY setting is always...

CHAPTER 3 CONTROL PANEL
3-37
MODEMENUFactory Setting
SOURCE=AUTO
MP FIRST=OFF
MP SIZE==A4/LTR
MANUAL FEED=OFF
PAPER
DUPLEX
=OFF
RESOLUTION=600
HRC=MEDIUM
TONER SAVE=OFF
QUALITY
DENSITY
=0
LANGUAGE=ENGLISH
LCD DENSITY=0
POWER SAVE TIME=5 MIN.
AUTO CONTINUE=OFF
LOCK PANEL=OFF
REPRINT=ON
EMULATION=AUTO (EPSON)
SETUP
KEEP PCL
=OFF 

USER’S GUIDE
3-38
MODEMENUFactory Setting
MEDIA TYPE=PLAIN PAPER
PAPER=A4/LETTER
COPIES=1
ORIENTATION=PORTRAIT
PRINT POSITIONX OFFSET=0
Y OFFSET=0
AUTO FF TIME=5
FF SUPPRESS=OFF
FONT NO.=59
FONT PITCH/POINT=10.00/12.00
SYMBOL/CHARACTER SET=PC8
AU TO  L F = O F F
AUTO CR=OFF
AUTO WRAP=OFF
AUTO SKI=ON
LEFT MARGIN=####
RIGHT MARGIN=####
TOP MARGIN=####
BOTTOM MARGIN=####
PRINT MENU
HP LASER JET
LINES=#### 

CHAPTER 3 CONTROL PANEL
3-39
MODEMENUFactory Setting
FONT NO.=59
FONT PITCH/POINT=10.00/12.00
SYMBOL/CHARACTER SET=US ASCII
AU TO  L F = O F F
AUTO MASK=OFF
LEFT MARGIN=####
RIGHT MARGIN=####
TOP MARGIN=####
BOTTOM MARGIN=####
EPSON FX-850
LINES=####
FONT NO.=59
FONT PITCH/POINT=10.00/12.00
SYMBOL/CHARACTER SET=PC8
AU TO  L F = O F F
AUTO CR=OFF
LEFT MARGIN=####
RIGHT MARGIN=####
TOP MARGIN=####
BOTTOM MARGIN=####
IBM PROPRINTER
LINES=#### 

USER’S GUIDE
3-40
MODEMENUFactory Setting
ERROR PRINT=OFFBR-SCRIPT
APT=OFF
TCP/IP ENABLE=ON
IP METHOD=AUTO
IP ADDRESS=192.0.0.192
SUBNET MASK=0.0.0.0
GATEWAY=0.0.0.0
IP BOOT TRIES=3
TCP/IP
IP METHOD=AUTO
NETWARE ENABLE=ONNETWARE
NEE FRAME=AUTO
APPLETALK=ON
NETBEUI=ON
DLC/LLC=ON
BANYAN=ON
LAT=ON
NETBIOS/IP=ON
NETWORK
ENET
=AUTO