Brother Laserprinter Hl 1030 1240 1250 User Guide

CHAPTER 4 TROUBLESHOOTING
MEMORY FULL 
· Press the panel button to print the data remaining in the
RESOLUTION ADAPTED
FUSER MALFUNCTION  
· Turn the power switch off, wait a few seconds and then turn it
LASER BD MALFUNCTION  
· Turn the power switch off, wait a few seconds and then turn it
SCANNER MALFUNCTION  
· Turn the power switch off, wait a few seconds and then turn it
D-RAM ERROR  
· Turn the power switch off, wait a few seconds and then turn it
NV-RAM ERROR  
· Turn the power switch off, wait a...

4-8
Error message printouts
The printer will report problems by printing an error message as defined in the
following table. Take the corrective actions for the error message the Printout
reports.
Error message Action
MEMORY FULL
· Press the panel button to print the data remaining in the
printer.
· Reduce the print resolution or reduce the complexity of your
document.
(For HL-1250 Only)
· Expand the printer memory by adding a commercially
available SIMM.  Refer to ‘How to add extra Memory’ in
Chapter...

CHAPTER 4 TROUBLESHOOTING
4-9
Error Message Action
SERIAL INTERFACE
OVERRUN ERROR
(HL-1250 Only)· Press the control panel button to resume printing.
· If the error occurs again, the interface’s hardware may be
damaged.  Please consult your dealer.
SERIAL INTERFACE INPUT
BUFFER OVERFLOW
(HL-1250 Only)· Press the control panel button to resume printing.
· Check the communication parameter settings such as the
handshake protocols on both your computer and printer.
· If the error occurs again, the interface...

4-10
Paper Handling
First, ensure that you are using paper that meets Brother recommended paper specifications.  See
“What kind of paper can I use” in Chapter 1.
Problem Recommendation
The printer does not load
paper.· If there is paper in the paper cassette, make sure it is straight. If
the paper is curled, you should straighten it before printing.
Sometimes it is helpful to remove the paper, turn the stack over
and put it back into the paper cassette.
· Reduce the amount of paper in the paper cassette,...

CHAPTER 4 TROUBLESHOOTING
4-11
PAPER JAMS and how to clear them
When a paper jam occurs, the printer indicates by lighting the LEDs as shown
below.
Ready
Alarm Paper
Toner
Data
Drum
Fig. 4-3  LED indication caused by a paper jam
 
Warning
After you have just used the printer, some internal parts of the printer are
extremely hot. When you open the front or rear cover of the printer, never
touch the shaded parts shown in the following diagram.
 High temperature High temperature
 
    
Front view Rear view...

4-12
Clear the jammed paper referring to the following description or you can view the
paper jam instructional video on the CD-ROM.
If the jammed paper is removed completely by using the information in the
following steps, you can close the paper cassette first, then close the front cover and
the printer will resume printing automatically.  If the printer does not resume
printing automatically, press the control panel button.  If the printer still does not
resume printing, please check that all the...

CHAPTER 4 TROUBLESHOOTING
4-13

 
  2.Pull any jammed paper up and out of the printer.
Fig. 4-6  Pull the jammed paper up and out

 
  3.Open the front cover. 

CHAPTER 4 TROUBLESHOOTING
Fig. 4-7  Remove the drum unit assembly
Fig. 4-8  Pull the jammed paper 

CHAPTER 4 TROUBLESHOOTING
4-15
!Caution
Do not touch the electrodes shown below to prevent damage to the printer caused by
static electricity.
Fig. 4-9  Electrodes

 
  5.Open the rear cover and pull the jammed paper out of the fuser unit.
If you have to pull the paper towards the back of the printer, the fuser may get dirty
with toner powder and may result in toner scatter on the next printed page or pages.
Print a few copies of the test page until the toner scatter on the printed pages stops.
Fig....

4-16
Problem  Recommendation
The printer cannot print.
For printing with the Serial Interface  (For HL-1250 Only)
Unable to print from
For DOS users  (For HL-1240/1250 Only)
Unable to print from