Brother HL 6050D User Manual

1 - 23   ABOUT THIS PRINTER
Printing on envelopes from the MP tray 
When the back output tray is pulled down, the printer has a straight paper path from the MP tray through 
to the back of the printer. Use this paper feed and output method when you want to print envelopes.
1Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver.
Media Type: Envelopes
Paper Source: MP Tray
PCL (standard) printer driver
BR-Script printer driver
The printer automatically turns on the MP...

ABOUT THIS PRINTER   1 - 24
2Open the back output tray, and then pull out the face up output tray support if necessary.
Figure 1-28
3Open the MP tray and lower it gently.
Figure 1-29
4Pull out the MP tray support flap.
Figure 1-30
 

1 - 25   ABOUT THIS PRINTER
5Put envelopes in the MP tray so that they touch the back of the tray and remain under the maximum 
paper height guides on both sides of the tray. Put the side to be printed on first, face up, with the 
leading edge (top) of the envelope in first. Do not put more than 3 envelopes in the MP tray at any 
one time, or it may cause a jam.
Figure 1-32
Envelopes that have been creased after they have been printed
At the back of the printer, open the back output tray and push down...

ABOUT THIS PRINTER   1 - 26
6Press and slide the paper width guide to fit the envelope size.
Figure 1-33
7Send the print data to the printer.
8After you finish the print job, close the back output tray.
DL size double-flap envelopes
■If the DL size double flap envelope is creased after printing, go to the Basic tab, select Paper 
Size and then select DL Long Edge. Put a new DL size double-flap envelope in the MP tray with 
the longest edge of the envelope in first, then print again.
When you put...

1 - 27   ABOUT THIS PRINTER
■If envelopes get smudged during printing, in the printer driver select MP Tray as the Paper 
Source for a straight paper path. Then, set the Media Type to Thick Paper or Thicker Paper 
to increase the fixing temperature. To adjust the print density setting, See QUALITY on page 
3-15.
■Envelope joints that are sealed by the manufacturer should be secure.
■All sides should be properly folded without any wrinkles or creases.
 

ABOUT THIS PRINTER   1 - 28
Printing on transparencies
You can print on transparencies from the paper tray or MP tray.
Printing on transparencies from the paper tray
1Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver.
Media Type: Transparencies
Paper Source: Tray 1 (or Tray 2)
PCL (standard) printer driver
BR-Script printer driver
WDo not touch transparencies that have just been printed because they are very hot.
Do not put more than 10 transparencies in the paper...

1 - 29   ABOUT THIS PRINTER
2Pull the paper tray completely out of the printer.
Figure 1-34
3While pressing the blue paper guide release levers, slide the paper guides to fit the transparency 
size. Check that the guides are firmly in the slots.
Figure 1-35
4Put transparencies in the tray. Put the side that is going to be printed on face down, with the top of 
the paper at the front of the tray. Check that the transparencies are flat in the tray at all four corners.
Figure 1-36
 

ABOUT THIS PRINTER   1 - 30
5Put the paper tray firmly back in the printer. Check that it is inserted fully into the printer.
Figure 1-38
6Send the print data to the printer.
Figure 1-39
Caution
Remove each transparency before the next page is output on the top output tray to prevent 
transparencies from sticking to each other.
Do not put more than 10 transparencies in the tray at any one time, or it may cause a jam. Check 
that transparencies are below the maximum paper mark (▼).
Figure 1-37
 

1 - 31   ABOUT THIS PRINTER
Printing on transparencies from the MP tray 
When the back output tray is pulled down, the printer has a straight paper path from the MP tray through 
to the back of the printer.
1Select the Paper Size, Media Type, Paper Source, and other settings in the printer driver.
Media Type: Transparencies
Paper Source: MP Tray
PCL (standard) printer driver
BR-Script printer driver
The printer automatically turns on the MP Tray mode when you put paper in the MP tray.
 

ABOUT THIS PRINTER   1 - 32
2Open the back output tray, and then pull out the face up output tray support if necessary.
Figure 1-40
3Open the MP tray and lower it gently.
Figure 1-41
4Pull out the MP tray support flap. 
Figure 1-42