Brother DCP 7060DR User Manual

							1
Start HereDCP-7055 / DCP-7057 / DCP-7060D
Quick Setup Guide
CHN-ENG Version A Please read the Safety and Legal booklet first before you set up your machine. Then, please read this Quick Setup 
Guide for the correct setup and installation.
To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/
.
1
Unpack the machine and check the components
WARNING indicates a potentially hazardous situation which, if not avoided, 
could result in death or serious injuries.
CAUTION
  indicates a potentially hazardous situation which, if not avoided, may 
result in minor or moderate injuries.
Quick Setup Guide Basic User’s Guide Safety and Legal booklet
Drum Unit and Toner 
Cartridge Assembly 
(pre-installed)Installation CD-ROM, 
Documentation CD-ROMAC Power Cord USB Interface Cable
WARNING
CAUTION
 
						

							2
WARNING
Plastic bags are used in the packaging of your machine. Plastic bags are not toys. To avoid danger of 
suffocation, please keep these bags away from babies and children and dispose of them correctly.
CAUTIONCAUTION
When you move the machine, grasp the side handholds that are under the scanner. DO NOT carry the machine 
by holding it at the bottom.
Note
• Keep a minimum gap around the machine as shown in the illustration.
• The components included in the box may differ depending on your country.
• Please save the original packaging should you need to ship the machine in future.
• If for any reason you must ship your machine, carefully repack the machine in the original packaging to avoid 
any damage during transit. The machine should be adequately insured with the carrier. For how to repack 
the machine, see Packing and shipping the machine in the Advanced Users Guide.
• To ensure safe operation the supplied plug must be inserted only into a standard power outlet that is properly 
grounded through the standard electrical wiring. Non grounded equipment may cause an electrical shock 
hazard, and may cause excessive electrical noise radiation.
USB cable
• It is recommended to use a USB 2.0 cable (Type A/B) that is no longer than 2 metres.
Network cable
Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX Fast Ethernet 
Network.
100 mm 100 mm90 mm
350 mm
 
						

							3
2
Remove the packing 
material from the 
machine
aRemove the packing tape from the outside of 
the machine and the film covering the scanner 
glass.
bOpen the front cover.
cRemove the Silica Pack from the inside of the 
machine.
CAUTIONCAUTION
DO NOT eat the Silica Pack. Please discard. 
If ingested seek medical attention immediately.
dLift the elastic band off the drum.
ePull the paper strip to remove the protective 
material as shown in the illustration.
fTake out the drum unit and toner cartridge 
assembly.
 IMPORTANT
DO NOT connect the AC power cord yet.
 
						

							4
gGently shake it from side to side several times 
to distribute the toner evenly inside the 
assembly.
hPut the drum unit and toner cartridge assembly 
back in the machine.
iClose the front cover of the machine.
3
Load paper in the paper 
tray
aPull the paper tray completely out of the 
machine.
bWhile pressing the green paper-guide release 
levera, slide the paper guides to fit the paper 
size you are loading in the tray. Make sure that 
the guides are firmly in the slots.
1
 
						

							5
cFan the stack of paper well to avoid paper jams 
and misfeeds.
dPut paper in the tray and make sure:
The paper is below the maximum paper 
mark (bbb)a.
Over filling the paper tray will cause paper 
jams.
The side to be printed on must be face down.
The paper guides touch the sides of the 
paper so it will feed correctly.
ePut the paper tray firmly back in the machine. 
Make sure that it is completely inserted into the 
machine.
4
Connect the power cord
aConnect the AC power cord to the machine, 
and then plug it into an electrical socket.
bTurn on the machine’s power switch.
1
 
						

							6
5
Choose your language
(If needed)
aPress Menu.
bPress a or b to choose 1.General Setup. 
Press OK.
cPress a or b to choose 0.Local Language.
Press OK.
dPress a or b to choose your language.
Press OK.
ePress Stop/Exit.
6
Set the LCD contrast 
(if needed)
If you are having difficulty reading the LCD, try 
changing the contrast setting.
aPress Menu.
bPress a or b to choose 1.General Setup. 
Press OK.
cPress a or b to choose 3.LCD Contrast. 
Press OK.
dPress a to increase the contrast.
—OR—
Press b to decrease the contrast.
Press OK.
ePress Stop/Exit.
 
						

							7
Windows
®USBMacintosh
 
7
Choose your connection type
For USB Interface Users
Windows®, go to page 8
Macintosh, go to page 10
Note
You can download the latest drivers and utilities for your machine from the Brother Solutions Center at 
http://solutions.brother.com/
.
 
						

							8
Windows®USB
For USB Interface Users 
(Windows® 2000 Professional/XP/XP Professional x64 Edition/Windows Vista®/Windows® 7)
8
Before you install
aMake sure that your computer is ON and you 
are logged on with Administrator rights.
9
Install MFL-Pro Suite
aPut the installation CD-ROM into your 
CD-ROM drive. If the model name screen 
appears, choose your machine. If the language 
screen appears, choose your language.
bClick Initial Installation and then Install 
MFL-Pro Suite.
cClick Yes if you accept the license agreements.
dFollow the on-screen instructions until this 
screen appears.
 IMPORTANT
• If there are any programs running, close 
them.
• The screens may differ depending on your 
operating system.
Note
• The installation CD-ROM includes Presto! 
PageManager. This software supports 
Windows
® 2000, Windows® XP, XP 
Professional x64 Edition, Windows Vista® and 
Windows® 7. Update to the latest Windows® 
Service Pack before installing MFL-Pro Suite.
• Before installation, if the USB cable is 
connected to the computer, the Found New 
Hardware Wizard dialog box will automatically 
show, please cancel it to close the screen.
Note
If the Brother screen does not appear 
automatically, go to My Computer (Computer), 
double-click the CD-ROM icon, and then 
double-click start.exe.
Note
• If the installation does not continue 
automatically, open the top menu again by 
ejecting and then reinserting the CD-ROM or 
double-click the start.exe program from the 
root folder, and continue from step b to install 
MFL-Pro Suite.
• For Windows Vista
® and Windows®7 users, 
when the User Account Control screen 
appears, click Allow or Yes.
 
						

							9
Windows®USB
Windows
®USBMacintosh
 
eConnect the USB cable to the USB connector 
marked with the   symbol on your machine 
and then connect the cable to your computer.
fTurn the machine on, and follow the on-screen 
instructions to complete setup.
 IMPORTANT
DO NOT cancel any of the screens during the 
installation. It may take a few seconds for all 
screens to appear.
Note
• For Windows Vista® and Windows®7 users, 
when the Windows Security screen appears, 
select the check box and click Install to 
complete the installation correctly.
• If an error message appears during the 
software installation, run the 
Installation Diagnostics located in 
Start/All Programs/Brother/DCP-XXXX 
(where DCP-XXXX is your model name).
Finish
The installation is now 
complete.
Note
• Depending on your security settings, a 
Windows Security or antivirus software window 
may appear when using the machine or its 
software. Please allow or permit the window to 
continue.
•XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is 
the most suitable driver for Windows Vista
® and 
Windows
® 7 when printing from applications 
that use the XML Paper Specification 
documents. Please download the latest driver 
by accessing the Brother Solutions Center at 
http://solutions.brother.com/
.
 
						

							10
MacintoshUSB
For USB Interface Users (Mac OS X 10.4.11 - 10.6.x)
8
Before you install
aMake sure your machine is connected to the 
power and your Macintosh is ON. You must be 
logged on with Administrator rights.
bConnect the USB cable to the USB connector 
marked with the   symbol on your machine 
and then connect the cable to your Macintosh.
cMake sure your machine’s power switch is on.
9
Install MFL-Pro Suite
aPut the installation CD-ROM into your 
CD-ROM drive.
bDouble-click the Start Here OSX icon. Follow 
the on-screen instructions.
cFollow the on-screen instructions until this 
screen appears. Choose your machine from 
the list, and then click OK.
dWhen this screen appears, click Next.
 IMPORTANT
For Mac OS X 10.4.10 users, upgrade to 
Mac OS X 10.4.11 - 10.6.x. (For the latest 
drivers and information on the Mac OS X you 
are using, visit http://solutions.brother.com/
.)
Note
It may take a few minutes for installation to 
complete.
The installation of MFL-Pro Suite is now 
complete. 
Go to step10 on page 11.