Brother Dcp 7010r User Manual

							
Introduction1 - 3
1
Control panel overview
Stack  Copies:01
100%  ……„…… Auto
1 Copy keys
(Temporary settings):
Options
You can quickly and easily select temporary 
settings for copying.
Enlarge/Reduce
Lets you enlarge or reduce copies depending 
on the ratio you select.
Contrast
Lets you select the copy quality for your type of 
document.
Number of Copies
Use this key to make multiple copies.
2  Menu Mode:
Menu
Lets you access the Menu to program.
 or 
Press to scroll through the menus and options.
Also you can use these keys to enter numbers.
Set
Lets you store your settings in the machine.
3  Scan
Lets you access Scan mode.
4 Start
Lets you start making copies or start scanning.
5 Stop/Exit
Stops an operation or exits from the menu.
6 Print key:
 
Job Cancel
You can cancel a print job and clear the print 
memory.
7  Liquid Crystal Display (LCD)
Displays messages on the screen to help you 
set up and use your machine.
 
						

							
Chapter 1
1 - 4
Load document
You can make copies and scan from the ADF 
(automatic document feeder) and from the 
scanner glass.
Note
ADF is not available for DCP-7010.
Using the automatic 
document feeder (ADF) 
(DCP-7025 only)
The ADF can hold up to 35 pages and feeds 
each sheet individually. Use standard 
(80 g/m
2) paper and always fan the pages 
before putting them in the ADF.
■Make sure documents written with ink are 
completely dry.
■Documents to be scanned must be from 
147.3 to 215.9 mm wide and 147.3 to 
356 mm long.
1Fan the pages well. Make sure you put 
the documents  face up, top edge first 
in the ADF until you feel them touch the 
feed roller. 
2Adjust the paper guides to fit the width of 
your documents.
3Unfold the ADF document output 
support flap.
Improper Setup
■DO NOT  use paper that is curled, 
wrinkled, folded, ripped, stapled, 
paper-clipped, pasted or taped.
■DO NOT  use cardboard, newspaper or 
fabric.
CAUTION
■DO NOT  pull on the document while it 
is feeding.
■Thick documents left on the scanner 
glass may cause the ADF to jam.
 
						

							
Introduction1 - 5
1
Using the scanner glass
You can use the scanner glass to copy or 
scan pages of a book or one page at a time. 
Documents can be up to 215.9 mm wide and 
297 mm long.
Note
DCP-7025 only:
To use the scanner glass, the ADF must be 
empty.
1Lift the document cover.
2Using the document guidelines on the 
left, centre the document face down on 
the scanner glass.
3Close the document cover.
Place documents face down on the 
scanner glass.
CAUTION
If the document is a book or is thick, do not 
slam the cover or press on it.
 
						

							
Chapter 1
1 - 6
About paper
Recommended Paper
To get the best print quality, we suggest using 
the following paper. 
■Use paper that is made for plain-paper 
copying.
■Use paper that is 75 to 90 g/m2.
■Use neutral paper. Do not use acidic or 
alkaline paper.
■Use long-grain paper.
■Use paper with a moisture content of 
approximately 5%.
Choosing acceptable paper
We recommend that you test paper 
(especially special sizes and types of paper) 
on the machine before purchasing large 
quantities.
For optimum printing, use a recommended 
type of paper, especially for plain paper and 
transparencies. For more information on 
paper specifications, call your nearest 
authorized sales representative or the place 
where you purchased your machine.
■Use labels or transparencies that are 
designed for use in laser printers.
■If you are using special paper and the 
machine has problems feeding from the 
paper tray, try again using the manual 
feed slot.
■You can use recycl ed paper in this 
machine.
Paper Type Item
Plain paper Xerox Premier 80 g/m
2
Xerox Business 80 g/m2
M-real DATACOPY 80 g/m2
IGEPA X-Press 80 g/m2
Recycled paper Xerox Recycled Supreme
Transparency 3M CG 3300
Labels Avery laser label L7163
 
						

							
Introduction1 - 7
1
Paper capacity of the paper trays
CAUTION
Do not  use the following types of paper or envelopes, they may cause a paper jam and 
damage your machine.
Do not use:
 Inkjet paper;
 Coated paper, such as vinyl coated paper;
 Pre-prined or highly textured paper, or paper with an embossed letterhead;
 Label sheets that have had any labels removed;
 Paper that has been previously printed on;
 Paper that cannot be arranged uniformly when stacked;
 Paper that is made with a short grain;
 Damaged, curled, wrinkled, or irregularly shaped paper.
Do not use:  Envelopes that have a baggy construction;
 Envelopes that are embossed (have raised writing on them);
 Envelopes that have clasps on them;
 Envelopes that are not sharply creased;
 Envelopes that are pre-printed on the inside.
Paper size Paper types No. of sheets
Paper  tray A4, Letter, Executive, A5, A6,  B5 and B6 Plain paper, Recycled paper up to 250 
(80 g/m
2)
Transparency up to 10
Manual feed slot Width: 69.9 - 215.9 mm  Length: 116 - 406.4 mm Plain paper, Recycled paper, 
Bond paper, Envelope, Label 
and Transparency1
4 mm or 
longer 4 mm or 
longer
 
						

							
Chapter 1
1 - 8
How to load paper
To load paper or other media in the 
paper tray
1Pull the paper tray completely out of the 
machine.
2While pressing the paper guide release 
lever, slide the adjusters to fit the paper 
size.
Check that the guides are firmly in the 
slots.
3Fan the stack of paper well to avoid 
paper jams and mis-feeds.
4Put paper in the paper tray.
5Put the paper tray firmly back in the 
machine and unfold the output paper 
tray support flap before you use the 
machine.
Note
When you put paper in the paper tray, please 
remember the following:
■Check that the paper is flat in the tray and 
below the maximum paper mark, and that 
the paper guides are touching the sides of 
the paper stack.
■The side to be printed on must be face 
down.
Maximum Paper Mark
Output Paper 
Tray Support 
Flap
 
						

							
Introduction1 - 9
1
To load paper or other media in the 
manual feed slot
You can load envelopes and special print 
media one at a time into this slot. Use the 
manual feed slot to print or copy on labels, 
envelopes or thicker paper. 
1Slide the paper guides to fit the paper 
size.
2Using both hands put the one sheet of 
paper in the manual feed slot until you 
feel the front edge of the paper touch the 
paper feed roller. Let go of the paper 
when you feel the machine feed the 
paper in a short distance.
Note
When you put paper in the manual feed slot, 
please remember the following:
■The side to be printed on must be face up.
■Put the leading edge (top of the paper) in 
first and push it gently into the slot.
■Make sure that the paper is straight and in 
the proper position on the manual feed 
slot. If it is not, the paper may not be fed 
properly, resulting in a skewed printout or 
a paper jam.
■Do not put more than one sheet or 
envelope in the manual feed slot at a time, 
or you may cause the machine to jam.
■You can remove smaller sizes of printed 
paper from the output paper tray more 
easily if you lift the scanner cover, using 
both hands, as shown in the illustration.
You can still use the machine when the 
scanner cover is raised. You can return 
the scanner cover to its home position by 
pushing it down with both hands.
 
						

							
2 - 1
2
Initial Setup
Setting the Paper Type
To get the best print quality, set the machine 
for the type of paper you are using.
1Press Menu and   or   to select 
1.General Setup.
Press  Set.
2Press   or   to select 
1.Paper Type.
Press  Set.
3Press   or   to select Plain, 
Thin, Thick, Thicker, 
Transparency or Recycled Paper.
Press  Set.
4Press  Stop/Exit .
Note
■The machine ejects paper with printed 
surfaces face down onto the output paper 
tray in the front of the machine. When you 
use transparencies or labels, remove 
each sheet immediately to prevent 
smudging or paper jams.
■You can select Transparency in Step 3 
if Letter or A4 paper size has been 
selected.
Setting the Paper Size
You can use seven sizes of paper for printing 
copies: Letter, A4, A5, A6, B5, B6 and 
Executive. When you change the size of 
paper you load in the paper tray, you will need 
to change the setting for paper size at the 
same time so your machine can fit a reduced 
copy on the page.
Note
If you selected Transparency as the paper 
type, you will only be able to select Letter or 
A4 size paper in Step  3.
1Press  Menu and   or   to select 
1.General Setup.
Press  Set.
2Press  or  to select 
2.Paper Size.
Press  Set.
3Press  or  to select Letter, A4, 
A5, A6, B5, B6 or Executive.
Press  Set.
4Press  Stop/Exit .
Getting started
General Setup
1.Paper Type
General Setup
2.Paper Size
 
						

							
Getting started2 - 2
2
Setting the Beeper Volume
You can change the beeper volume. The 
default setting is 
Med. When the beeper is on, 
the machine will beep when you press a key 
or make a mistake.
1Press  Menu and   or   to select 
1.General Setup.
Press  Set.
2Press  or  to select 3.Beeper.
Press  Set.
3Press  or  to select Low, Med, 
High or Off.
Press  Set.
4Press  Stop/Exit .
Toner Save
You can conserve toner using this feature. 
When you set Toner Save to 
On, print 
appears lighter. The default setting is 
Off.
1Press  Menu and   or   to select 
1.General Setup.
Press  Set.
2Press  or  to select 4.Ecology.
Press  Set.
3Press   or   to select 
1.Toner Save.
Press  Set.
4Press   or   to select On (or Off).
Press  Set.
5Press  Stop/Exit .
General Setup
3.Beeper
General Setup
4.Ecology
 
						

							
Chapter 2
2 - 3
Sleep Time
Setting the Sleep Time reduces power 
consumption by turning off the fuser inside 
the machine while it is idle. You can choose 
how long the machine is idle (from 00 to 99 
minutes) before it goes into sleep mode. The 
timer is automatically reset when the machine 
receives PC data or makes a copy. The 
factory setting is 05 minutes. While the 
machine is in sleep mode you will see 
Sleep 
on the LCD. If you try to print or copy in sleep 
mode, there will be a short delay while the 
fuser warms up to its working temperature.
1Press  Menu and   or   to select 
1.General Setup.
Press  Set.
2Press   or   to select 4.Ecology.
Press  Set.
3Press   or   to select 
2.Sleep Time.
Press  Set.
4Use the   or   to enter the length of 
time the machine is idle before it goes 
into sleep mode (00 to 99).
Press  Set.
5Press  Stop/Exit .
Note
If you want to turn off sleep mode, press  Start 
and  Options  simultaneously in Step  3.
Setting the LCD Contrast
You can change the contrast to help the LCD 
look lighter or darker.
1Press  Menu and   or   to select 
1.General Setup.
Press  Set.
2Press  or  to select 
5.LCD Contrast.
Press  Set.
3Press  or  to select Light or 
Dark.
Press  Set.
4Press  Stop/Exit .
Printing the User Settings List
You can print a list of your settings.
1Press Menu and   or   to select 
1.General Setup.
Press  Set.
2Press  or  to select 
6.User Settings.
Press  Set.
3Press  Start.
General Setup
4.Ecology
Ecology
2.Sleep Time
General Setup
5.LCD Contrast
General Setup
6.User Settings