Brother Dcp 7010r User Manual

3 - 1
3
3
Using the machine as a 
copier
You can use your machine as a copier, 
making up to 99 copies at a time.
The printable area of your machine begins at 
approximately 2 mm from both sides and 3 
mm from the top or bottom of the paper.
Note
The printable area shown above is for a 
single copy or a 1 in 1 copy using A4 size 
paper. The printable area changes with the 
paper size.
Making a single copy
1Load your document.
2Press Start.
Making multiple copies
1Load your document.
2Press  Number of...

Chapter 3
3 - 2
Using the Temporary 
Copy keys
When you want to quickly change the copy 
settings temporarily for the next copy, use the 
Temporary Copy keys. You can use different 
combinations.
Note
■The machine returns to its default settings 
60 seconds after it finishes copying.
■You can save the copy settings you use 
most often by setting them as default. 
(See  Changing the default copy settings  
on page 3-7.)
Enlarging or reducing the 
image copied
You can select the following enlargement or...

Making copies3 - 3
3
3Press  or  to select the 
enlargement or reduction ratio you want.
Press Set.
— OR —
You can select 
Custom(25-400%) and 
press  Set.
Press  or  to enter an 
enlargement or reduction ratio from 
25% 
to 
400%.
Press  Set.
Note
Enlargement or reduction ratio can also be 
increased or decreased by holding down   
or .
4Press  Start.
— OR —
Press other temporary copy keys for 
more settings.
Note
■Special Copy Options (2 in 1 (P), 
2 in 1 (L), 4 in 1 (P), 4 in 1 (L) 
or 
Poster(3 x...

Chapter 3
3 - 4
Changing the temporary copy settings
Use the  Options  key to quickly set the following copy settings temporarily for the next copy.
Note
The factory settings are shown in Bold.
After you choose your settings by pressing  Set, the LCD shows Set temporarily.
Press  Start if you have finished choosing settings.
Press  Menu Selections Options Page
Quality Auto
Text
Photo3-5
Stack/Sort
(DCP-7025 only)
Stack
Sort3-5
Page LayoutOff(1 in 1)
2 in 1 (P)
2 in 1 (L)
4 in 1 (P)
4 in 1 (L)
Poster(3 x...

Making copies3 - 5
3
Quality
You can select the copy quality. The default 
setting is 
Auto.
1Load your document.
2Press Options  and   or   to select 
Quality.
Press  Set.
3Press   or   to select the copy 
quality you want (
Auto, Text or 
Photo).
Press  Set.
4Press  Start.
Sorting copies using the ADF 
(DCP-7025 only)
You can sort multiple copies. Pages will be 
stacked in the order  (1, 2, 3),  (1, 2, 3) 
and so on.
1Load your document.
2Press  Number of Copies  repeatedly 
until the number you want...

Chapter 3
3 - 6
If you are using the scanner glass:
6After the machine scans the page, 
the LCD shows: 
Press   to scan the next page.
7Put the next document on the scanner 
glass.
Press  Set.
Repeat Steps 6 and 7 for each page of 
the layout.
8After all the pages of the document have 
been scanned, press   to end.
Place document face up in the ADF in the 
direction shown below. (DCP-7025 only) 2 in 1 (P)
4 in 1 (P) Place document face down on the scanner 
glass in the direction shown below.
2 in 1 (P)...

Making copies3 - 7
3
Making a poster (Page Layout)
You can create a poster. When you use the 
Poster feature your machine divides your 
document into sections, then enlarges the 
sections so you can assemble them into a 
poster. If you want to print a poster, use the 
scanner glass.
Note
■Please make sure paper size is set to A4 
or 
Letter.
■For Poster copies, you cannot make more 
than one copy or use the Enlarge/Reduce 
feature.
1Load your document.
2Press  Options  and   or   to select 
Page...

Chapter 3
3 - 8
Adjusting contrast
You can change the contrast to help an image 
look sharper and more vivid.
1Press  Menu  and   or   to select 
2.Copy.
Press  Set.
2Press   or   to select 2.Contrast.
Press  Set.
3Press   to increase the contrast.
—OR —
Press   to decrease the contrast.
Press  Set.
4Press  Stop/Exit .
Out of Memory 
message
If the memory becomes full while you are 
making copies, the LCD message will guide 
you through the next step.
For DCP-7025:
If the 
Out of Memory message appears...

4 - 1
4
4
The User’s Guide on the CD-ROM includes the Software User’s Guide for features available when 
connected to a computer (for example, Printing and Scanning). The availability of the features 
listed below varies by model:
■Using the machine as a Printer (See Chapter 1 in the Software User’s Guide on the CD-ROM.)
■How to Scan (See Chapter 2 in the Software User’s Guide on the CD-ROM.)
■Using ControlCenter2.0 (See Chapter 3 in the Software User’s Guide on the CD-ROM.)
■Network Scanning (Optional...

5 - 1
5
IEC 60825-1 Specification
This machine is a Class 1 laser product as defined 
in IEC 60825-1 specifications. The label shown 
below is attached in countries where required.
This machine has a Class 3B Laser Diode which 
emits invisible laser radiation in the Scanner Unit. 
The Scanner Unit should not be opened under any 
circumstances.
Laser Diode
Wave length: 770 - 810 nm
Output: 5 mW max.
Laser Class: Class 3B
Disconnect device
This product must be installed near an electrical 
socket that is...