Boxlight Projectowrite 2 User Manual

48
Registering And Conguring The Projector
Link
  Select the registered projector in monitor window. 
Click mouse right key and select “ 
Link ” to show up the control panel table and the projector connected status.
< Graph 12 > : The control panel table  

Control Panel Window Introduction
49
Control Panel Window Introduction
  Power Control
Icon Name
Power on
Power off
  Input Source
Icon Name
Video
S-Video
Y,Pb,Pr
DVI-I
RGB 1
Change Input Source
  Function Key
Icon Name Icon Name
UpFreeze
DownBlank
LeftKeystone Correction +
RightKeystone Correction -
MenuIncrease Brightness
Auto SyncDecrease Brightness
MuteHigher Contrast 

50
Control Panel Window Introduction
 Function Key
Icon Name
Lower Contrast
Zoom In
Zoom Out
Volume Up
Volume Down
 Projector Status
Icon Name
System Status
Input Source Status
Lamp Timer
Air Filter Timer   

51
Control Panel Window Introduction
 Network Control Window introduction
Icon Name Description
Scan all Capture the all registered projectors’ information  
one time only.
Start Auto ScanAccording to the system setting, get the projector  
information automatically.
Stop Auto Capture Stop scanning the projector information.
Auto SearchSearch the projector in the same network to  
register and modify the setting.
Open Project File
Open project le which was saved.
Save Project File Save the registered...

Maintenance Of Projector
52
Maintenance of Projector
Air Filter 
When a warning message appears to remind you to clean the air lter,  
please replace a new one as soon as possible. Please check and clean the  
air lter periodically. 
Replacing the Air Filter 
When the use time reaches the lter counter time, the projector will  
display a message that indicates to replace a new lter. If there is no spare 
air lter available, please contact your dealer.
Turn off the projector, and unplug the power cord....

53
Maintenance of Projector
Lamp 
1.  If you want to replace new lamp, but the projector was just turned off, please let the projector cool down and unplug power cord at least 60  
minutes.
2.  If the projector is mounted in the ceiling, contact your dealer to replace  the lamp.
Replacing New Lamp 
1. Remove the lamp door. 
2.  Loosen 2 screws of the lamp holder. Take the handle on the top of the  lamp, pull out the lamp straight off the projector.
3. Insert new lamp, lock the lamp door rmly with 2...

54
Maintenance of Projector
 WARNING
The projector uses a high-pressure mercury lamp. 
The explosion of lamp with a loud bang or burn out could possibly cause 
injury or a re.
When the bulb burts, it is possible for shards of glass to y into the lamp 
housing; and for gas containing mercury to escapefrom the projector’s 
vent holes.
If the lamp has broken, do not check the inside of the projector. Please 
ventilate the room immediately.
Do not touch or bring your face close to the broken pieces since it...

55
Maintenance of Projector
Other Care 
Cleaning The Lens 
If the lens is dirty and dusty, display quality maybe decreased. Before  
cleaning the lens, please make sure that the projector is cool down 
adequately.
After the projector has cooled down adequately, lightly wipe the lens with 
the available lens-cleaning cloth.
Do not touch the lens directly with your hand. 
Additional 
- In order to ensure the safe use of your projector, please contact your dealer to inspect about once a year.
- Before...

Troubleshooting
56
Troubleshooting
Indicator 
The power and lamp indicators show the status of the projector. Before requesting repair, 
check the projector status using the chart below. If the problem cannot be resolved,  
contact your dealer. 
In normal status~~~
POWER LAMPCONDITIONS DESCRIPTION
Blinking In 
GreenOff Stand by mode Projector is ready to be turned on.
Lighting In 
GreenOff On mode Projector is on and operating.
Lighting In 
Green
Blinking In Red 
( Slow ) Cool down mode Projector is in...

57
Troubleshooting
Error For Machine Defects 
The following problems may be confused with a machine defect. Check and follow the  
table. If it couldn’t be improved, contact your dealer.
Symptom Cause / Remedy
Projector power 
does not turn on.The power cord is disconnected.
Plug the power cord into an AC outlet. 
Intending to turn on the projector again during the cool down mode. 
Wait until the cool down mode has completed. 
There is no lamp and/or lamp cover is not rmly closed. 
Please turn off the...