Boxlight Projectowrite 2 User Manual

8
Installation Guide for Window OS
5. How To UseThere is another quick way to change the position of icon bar or hide it. 
Point to left or right edge slightly outside the projected image, then push 
the button on Pointer or Light Pen.  

9
Installation Guide for Mac OS
1. System Requirements
To ensure the interactive function work properly, please check your  
computer to see if it meets the following conditions.
System Requirements
OS Required Mac OS X v10.4.11- v10.5 or above
Processor Type Intel processor or Power PC
RAM 512 MB RAM or above
Hard Disk At least 10 MB of hard disk space
Media Device At least 4x CD-ROM or DVD-ROM 
At least USB 2.0
2.  LightPen Software Installation
Step 1:  Insert the Installation Disc to the CD-ROM or...

10
Installation Guide for Mac OS
3. Select DistanceStep 1: Select LightPen from menu bar. 
Step 2: Click mouse key on Projection Distance.
Step 3:  Choosing the projection distance from pop-up menu  (>3m,>2m,

11
Installation Guide for Mac OS
4. Calibration
Step 1:  Select “LightPen” from menu bar then click mouse key for  calibration.
Step 2:  Push the button on Pointer or Light Pen (pending on the  screen size), and point to the Center of green cross target from  
upper-left of screen to lower-right of screen orderly. There are 
nine targets totally. When there is no more green target on the 
screen, it means you have completed the calibration procedure. 
To ensure accurate positioning, keep the angle of...

12
Installation Guide for Mac OS
5. How To UseHow to operate function of Ctrl + Click (Mouse right key)? 
 Point to top or lower edge slight outside the projected image, then push the button on Pointer or Light Pen.
        

13
Installation Guide for Mac OS
5. How To UseThere is another quick way to change the position of icon bar or hide it. 
 Point to left or right edge slightly outside the projected image, then push the button on Pointer or Light Pen.  

14
Troubleshooting
1. Q:  Why you can’t execute the LightPen program?A:      You might need to log in as “administrator” to be able to install 
program to your computer. Consult with your IT engineers to help  
you on this regard. 
2. Q: Why does it show “No LightPen found”? A:    Reasons for this might be:
          (1) USB  cable  is  not  well  connected  to  computer  or  projector.  Please 
check and make sure the cable is well connected bet ween computer 
and projector.
            (1-1)  If  the...

15
Troubleshooting
(C)(D)
 
*  Some Anti-virus programs will disable the USB port. Please make 
sure the USB port is not disabled.
 (2)  The  installation  of  LightPen  driver  is  not  comple te.  Please 
remove the LightPen driver and re-install.
           (3)  The  length  of  USB  cable  is  too  long.  The  USB  cabl e  should  be 
shorter  than  1.5M.  If  you  need  longer  USB  cable,  please  contact  
your dealer for proper USB extension cable.
           (4) USB port on computer...

16
Troubleshooting
            (2) The  ambient  may  be  too  strong. Avoid  direct  light ing  on  the 
projected image or CMOS sensor.
                  Strong ambient light is usually caused by the following:
                 (2-1)  Sunlight shines directly on the screen.
              (2-2)Light source working close to the sensor. 
            (3) In Window Vista system, one of green cross targets may be  hidden by Start square of computer/notebook computer. Please  
point to the position as shown...

17
Troubleshooting
5. Q: Why is the cursor jumping? 
     A:  This  may  be  caused  by  strong  ambient  light  interf erence.  Try  to 
avoid  strong  ambient  light  interference,  especially   strong  sun  light 
directly projected on the screen. (Please refer to the Question 3.)
6. Q:  Why  is  the  LightPen  not  working  after  the  compute r  wakes  up 
from standby?
     A:    In some cases, if the computer goes into standby  mode, the computer 
will  shot  the  USB  port.  In  such  case,...