Boxlight Pro5000sl Projector User Manual

							
11
Setting up
Using the Hiding-Styled Handle
Refer to the picture operation direction to 
pull the handle.
 
NOTE ►This handle is designed to carry the projector for short distance only.
►Please do not have added on other goods to use together, it can damage 
the projector.
Hiding-Styled Handle 
						

							
12
Putting batteries
Remote control
Please set the batteries to the remote control before using it. If the remote control starts
to malfunction, try to replace the batteries. If you will not use the remote control for long 
period, remove the batteries from the remote control and store them in a safe place. 
1.Remove the battery cover.
    Slide back and remove the battery cover in the 
    direction of the arrow.
2.Insert the batteries.
    Align and insert the two AAA batteries according 
    to their plusminus terminals 
3.Close the battery cover.
    Replace the battery cover in the direction of the 
    arrow and snap it back into place.
WARNING 
►Always handle the batteries with care and use them only as directed. 
Improper use may result in battery explosion, cracking or leakage, which\
 could 
result in fire, injury and/or pollution of the surrounding environment.
►Be sure to use only the batteries with the mentioned specification. 
►Do not use batteries of different types at the same time. 
►Do not mix a new battery with used one. Make sure the plus and minus 
terminals are correctly aligned when loading a battery.
►Keep a battery away from children and pets.
►Do not recharge, short circuit, solder or disassemble a battery.
►Do not allow a battery in a fire or water. 
►Keep batteries in a dark, cool and dry place. If you observe a leakage of a 
battery, wipe out and then replace a battery. If it adhere your body or \
clothes, 
rinse well with water immediately.
►Dispose of batteries in accord with environmental laws.
About the Battery 
						

							
13
Remote control
Using as a simple PC mouse & keyboard
The enclosed remote control works as a 
simple mouse and keyboard of the PC, 
when the projectors USB port connects 
with the PCs mouse port via a mouse 
cable.(SEE P4) 
CAUTION ►Improper use of the simple mouse & keyboard function could 
damage your equipment. While using this function, please connect this 
product only to a PC. 
About the remote control signal
1.The remote control works with the 
     projector’s remote sensor. This 
     projector have 2 remote sensors 
     on the front and back.
2.The sensor senses the signal within 
    the following range when the sensor 
    is active:30 degrees (15 degrees to 
    the left and right of the sensor) within 
    7 meters about.  
NOTE ► Laser pointer of the remote control is used in place of a finger or rod. 
Never look directly into the laser beam outlet or point the laser beam at other people. 
150150
remote sensor 
						

							
14
Turning on the power
Power on/off
Turning off the power
1.Make sure that the POWER indicator 
    turns in steady green and the lens 
    cover is removed.
2.Press the STANDBY/ON button on 
    the projector or the remote control.
3.The projection lamp will light up, 
     the LAMP indicator will not light in 
     red and the POWER indicator will 
     begin light in green.
To display the picture, select an input 
signal according to the section 
“Selecting an input signal” (SEE 15). 
WARNING►A strong light is emitted when the projector’s power is on. 
Do not look into the lens of the projector or look inside of the project\
or through
any of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or 
just after use, since it is too hot.
►Remove the power cord for complete separation.
MENU
ON/STANDY BY BUTTON POWER INDICATOR
MENU
LAMP INDICATOR
PCVideo
Lens cover
1.Press the ON/STAND BY button on the projector or 
the remote control. The message [ Power off. Please 
press key again to power off. ] will appear on the 
screen for about 5 seconds.Press again and the 
projector lamp will go off, the POWER indicator will 
begin light in green and the LAMP indicator will begin 
blinking in red.
 2.The LAMP indicator will stop blinking and light in 
red. And then the POWER indicator begin blinking 
in green when the lamp cooling is complete. Unplug 
the power cable.
Attach the lens cap.Do not turn the projector on 
immediately after turning off.Turning projector on 
again too soon could shorten the lifetime of some 
consumable parts of the projector. 
     
						

							
15
1.Press the VOLUME button on the remote control.
    A dialog will appear on the screen to aid you in 
    adjusting the volume.
2.Use the +/- cursor buttons to adjust the volume.
    To close the dialog and complete the operation, 
    press the MENU button and the menu will 
   disappear after a few seconds.
1.Press the MUTE button on the remote control. 
    A dialog will appear on the screen indicating 
    that you have muted the sound.
2.If you do not do anything, the dialog will 
    automatically disappear after a few seconds.
3.Press the MUTE button will bring the sound 
    back to the level before muting.
Selecting an input signal
1.To select a new input,press the PC button 
    on the projector or remote control. Each time 
    you press the button, the projector switches 
    its input port as below.
COMPUTER IN1COMPUTER IN2 
DVI
Operating
Adjusting the volume
Adjusting the mute
(continued on next page)
Volume
Mute
MENU
PC  BUTTON Video  BUTTON 
PC
Video
PCVideo
PCVideo
YPbPr

COMPOSITE VIDEO
2.If press the Video button on the remote 
    control.Each time you press the button, 
    the projector switches its input port as 
    below.
S-VIDEO 
						

							
VideoPC
16
Operating
YPbPr  
COMPOSITE VIDEO
MENU
MENU  BUTTON 
Searching an input signal
1.Please Press the MENU button on the 
     projector or remote control.
2.After you can use the     cursor button
    to chiose [ ON ]  in the AUTO SEARCH 
    item of the SETTING menu. 
The projector will start to check its input 
ports in order to find any input signals.
When an input is found, the projector 
will stop searching and display the 
image. If no signal is found, the projector will 
return to the source before searching and the 
projector switches its input port as below.  
         COMPUTER IN1    COMPUTER IN2 
  S-VIDEO  
Selecting an input signal (continued)
DVI 
Selecting an aspect ratio
1.Press the MENU button on the projector or remote control.
2.After you can select the RESIZE item of the ADVANCED menu. And use the
          /     cursor buttons to adjust the aspect ratio.
For a PC signal 
 4:3  16:9 
For a video signal ( s-video signal or component video signal)
4:3  16:9 
For no signal 
4:3 (fixed)
The RESIZE item does not work when no proper signal is inputted.
The NORMAL mode keeps the original aspect ratio setting.
Performing the automatic adjustment initializes the aspect ratio setting.
(continued on next page)
▲▲
▲
3.If press AUTO button on the projector.
Each time you press the button, the 
projector’s image is in Blank mode. 
Automatically adjusts the setting to 
match the current input.
VideoPC
AUTO  BUTTON  
						

							
17
Operating
Adjusting the zoom and focus
Adjusting the image position
When the place to put the projector is slightly uneven to the left or ri\
ght, use the 
feet to place the projector horizontally. Using the feet can also tilt t\
he projector in 
order to project at a suitable angle to the screen.
This projector has 2 feet and 2 knobs. 
A foot is adjustable while pulling up the knob on the same side as it.
1.Holding the projector, pull the knobs up to loose the feet.
2.Position the front side of the projector to the desired height.
3.Release the knobs in order to lock the feet.
4.After making sure that the feet are locked, put the projector gently.
 
CAUTION ►Do not handle the knobs without holding the projector,since the 
projector may drop down.
Holding the projector,press the adjustable knobs to extend the both feet\
. 
RING DOORZOOM RINGFOCUS RING
1.Use the focus ring to focus the picture.
2.Use the zoom ring to adjust the screen size.  
						

							
VideoPC
18
Operating
Correcting the keystone distortions
1.Please Press the MENU button on the projector or remote control.
2.After you can use the    /► cursor button to select  the KEYSTONE  V item of 
     the SETTING menu and press the    /► button for keystone adjustment.
(1)The KEYSTONE  V item will displays a dialog for keystone correction.
(2)To close the dialog and complete this operation, press the MENU button ag\
ain. 
     The dialog will automatically disappear after a few seconds if you do not do 
     anything.
(3) The adjustable range of this correction will vary among inputs. For some input, 
     this function may not work well.
(4) When the zoom adjustment is set to the TELE (telephoto focus), t\
he automatic 
     keystone distortion correction may be excessive. This function shou\
ld be used 
     when the zoom adjustment is set to the full WIDE (wide-angle focus\
) whenever 
     possible.
►
►
MENU
KEYSTONE  BUTTON 
Press [ Left ] and [ Right ] buttons to correct keystone distortion.
SCREENSCREEN 
						

							
VideoPC
VideoPC
19
Operating
1.Press the Still button on the remote control. 
    The [ Still ] indication will appear on the screen and the 
     projector will go into the Still mode.
 To exit the still mode and restore the screen to normal, press 
the still button again.
If the projector continues projecting a still image for a long time, 
the LCD panel might possibly be burned in. Do not leave the 
projector in the Still mode for too long.  
1.Press the Blank button on the projector or remote control. 
     The [ Blank ] indication will appear on the 
     screen and the projector will go into the 
     Blank mode.
 To exit from the blank screen and return to 
the input signal screen, press the BLANK 
button again.
If the projector is left in Blank mode for more
than 15 minutes, the projector will 
automatically shut off the lamp and begin
to cool-down mode.
 
MENU
BLANK  BUTTON 
Temporarily blanking the screen
Stilling the screen
Still
BLANK
NOTE ►The sound is not connected with the blank screen function. If 
necessary, set the volume or mute first.
Video
PC 
						

							
VideoPC
20
Operating
Using the menu function
This projector has the following categories: 
ADVANCED, AUDIO, INPUT, PICTURE, PRESENTATION,SETTING and 
SECURITY. ADVANCED MENU consists of functions often used, and the 
other menus are classified into each purpose. Each of these menus is operated 
using the same methods. The basic operations of these menus are as follo\
ws.
1.Press the MENU button on the remote control 
     or the projector.The MENU button on the 
     projector works as the cursor buttons.
2.Use the ▲/▼ cursor buttons to select an 
    category to operate.
3.Use the ◄/► cursor buttons to operate the 
    category.Then press the ► cursor button, 
     or the ENTER button to select an item. The 
     lower layer menu of the selected item 
     will appear.
4.Some functions cannot be performed 
     when a certain input port is selected, 
     or when a certain input signal is 
     displayed.
5.Reset all
    After you select [ Reset all ] on the menu, the following confirmati\
on message
    will appear on the screen. Press the MENU button or ignore the messa\
ge to 
    exit the [ Reset All ] function without changing any settings.
MENU
MENU  BUTTON CURSOR  BUTTON 
Reset all?
Please, press reset key to return default setting.
reset all                                                               \
Yes                                                                        \
     No
If select to reset all, press [ Yes ].