Boxlight Pro5000sl Projector User Manual

							 
NE 151 Highway 300, Suite A 
PO Box 2609 
Belfair, WA 98528 
360.464.2119 
www.boxlight.com 
Pro5000SL  
						

							
2
Aboutthismanual.....................1
Contents........................................2
Projectorfeatures.......................3
Preparations.................................3
Contentsofpackage.........................3
Partnames....................................4
Projector............................................4
Controlpanel....................................5
Remotecontrol.................................5
Picture menu(PC mode)......................21
Picture menu(Video mode).................22
Audio menu.........................................23
Setting menu(PC mode).....................24
Setting menu(Video mode).................25
Advanced menu..................................26
   Logo Setting.................................26-A
   Logo Capture................................26-B
Presentation menu..............................27
Security menu......................................28
   Auto filter alert..................................30
PIN Key in operation...........................31
Settingup......................................6
Arrangement.....................................6
Connectingyourdevices..................8
Connectingpowersupply................10
Usingthesecurityanchor................10
Usingthehiding-style Handle..........11
Remotecontrol..........................12
Puttingbatteries..............................12
Abouttheremotecontrolsignal......13
Usingasa simplePCmouse&
keyboard.........................................13
Poweron/off...............................14
Turningonthepower......................14
Turningoffthepower......................14
Operating....................................15
Adjustingthevolume......................15
Adjustingthemute..........................15
Selectinganinputsignal.................15
Searchinganinputsignal...............16
Selectinganaspectratio................16
Adjustingtheimage position..........17
Adjustingthezoomandfocus........17
Correctingthekeystone
distortions........................................18
Stilling the Screen...........................19
Temporarilyblankingthescreen.....19
Usingthemenufunction.................20
MENU
Maintenance...................................32
Lamp....................................................32
  Lamp Warning...................................33
Airfilter................................................34
Othercare...........................................35
Troubleshooting............................36
Appendix
Contents
Regarding the indicator lamps............36
Mistaken for machine defects.............37
List of supported Monitor Display.......39
Ceiling Mounted Installation Guide.....40
PIN code number memo.....................41 
						

							
3
1. Design with 3LCD optical system, provide you：Bright image, natural color, 
    smooth video playback and gentle for your eyes.
2. Design with high efficiency dust air filter and Auto Filter Alert. (See P30) 
3. Easy to maintenance design function.(See P32~35) 
4. Security PIN Lock function. (See P29) 
5. Progressive scans accommodating for High-definition 1080i form.  
6. Auto V keystone function, +/- 30 degrees.  
7. Auto brightness control. 
8. Auto ceiling function. 
9. Support DVI ,YPbPr ,Composite Video and  S-Video signal. (See P8) 
10. Hiding-Style Handle to carry the projector easily.  (See P11) 
Contents of package( Before Use )
Your projector should come with the items shown there. Contact immediately 
your dealer if anything is missing. 
Projector features 
Preparations
NOTE   ► Keep the original packing materials, for future reshipment.  
Be sure to use the original packing materials when moving the projector. 
(1)Projector and Lens Cap(2)Remote control
(3)Battery (for Remote Control use)
(4)User’s Manual (CD)
(5)Quick Start Guide(6)Power Cable(7)VGA Cable (7)USB Cable  
						

							
4
Part names 
Projector
(1) Lamp Cover
     The lamp is inside.
.
(2) Focus ring( SEE P17) 
(3) Zoom ring( SEE P17) (4) Control panel( SEE P5)     
(5) Speaker
(6) Adjustable knobs (x 2) (7) Adjustable feet (x 2) 
(8) Lens Cap
(9) Lens cover  (10) Intake vents(11) Filter cover
       The air filter is inside.  (12) Front IR receiver 
(13) Security anchor( SEE P10) 
(14) AC inlet( SEE P10) 
(15) S-VIDEO port( SEE P16)  (16) AUDIO L/R port( SEE P8) 
(17) VIDEO port( SEE P8) 
(18) COMPUTER IN1 port( SEE P8)  (19) COMPUTER IN2 / DVI port( SEE P8) 
(20) USB port( SEE P13)
(21) AUDIO 1 IN port( SEE P8) (22) AUDIO 2 IN port( SEE P8) 
(23) AUDIO OUT port ( SEE P8) 
(24) MONITOR OUT port (25) YPbPr port ( SEE P16) 
&(26) L-AUDIO IN-R port( SEE P8) 
(28) RS-232C port( SEE P8) 
(29) LAN port (Optional)( SEE P8) 
WARNING HOT! : 
Do not touch the lamp cover and the outlet vents during use or just after use, 
since it is too hot.Do not look into the lens or vents while the lamp is on, since the strong light
is not good for your eyes. 
CAUTION
Maintainnormalventilationtopreventtheprojectorfromheating up.Donotcover,
blockorplugupthevents.Donotplaceanythingthatcanstickorbesuckedtothevents,aroundtheintakevents.Changetheairfilterperiodically.
Do not use the security anchor to prevent the projector from falling down, since it
is not designed for it.
(1)      HOT!
(3) (2)(4)
(5)
(6)(7)(8)(9)
(10)
(11)
(13)
(22) (18)
(19)
(20)
(14)
(15) (17) (16) 
(25)&(26)
(24)
(12)
(23)
(21)(28)
(29) 
						

							
MENU
Part names 
5
Control panel
(1) ON/STANDBY button(SEE P14)  
(2) AUTO button(SEE P15)  (3) INPUT button(SEE P15)   
(4) BLANK button  
(5) KEYSTONE button (6) MENU button(SEE P16)  
(7)MENU-Left/Right      MENU-Up/Down 
(8) POWER indicator(SEE P10,P14)    
(9) LAMP indicator (SEE P14)  
Remote control
(1) Power button.(SEE P14) 
(2) Point button.(3) Mouse Left button. 
(4) Menu-up button / Menu-down button.
(5) Menu button. (6) Keystone up /down button.
(7) PC button.(SEE P15) 
(8) Video button.(SEE P16) (9) Auto button.(SEE P15) 
(10) Blank button.
(11) Still button.(12) Zoom in / Zoom out button.(SEE P17) 
(13) Mute button.(SEE P15) 
(14) Volume up / down button.(SEE P15) (15) Menu-left button / Menu-right button.
       Menu-up button / Menu-down button.
       (SEE P16) (16) Mouse Right button. 
(17) Laser pointer button. 
 
(1)
(2)
(3)(4)
(5)
(6)
(7)
(9)(8)
(1)
(3)
(2)
(5)
(15)
(6)
(7)
(8)
(9)
(10)(11)
(4)
(17)
(16)
(13)
(12)
(14)
PC
Video 
						

							
6
Setting up
Install the projector according to the environment and manner the projector will 
be used in.
Arrangement
TeleWideTeleWide
Screen size
(inch)
Distance (m)Distance (feet)
40
60
70
80
100
200
300
1.50
2.23
2.60
2.97
3.70
7.37
11.04
1.24
1.85
2.15
2.45
3.06
6.10
9.14
4.91
7.32
8.52
9.73
12.14
24.18
36.22
4.06
6.06
7.05
8.05
10.04
20.01
29.97
MM
The distance between the projector and screen determines the actual imag\
e size.Refer to 
this table, in case of 4:3 aspect ratios. The values M   shown in the table are calculated for 
a full size screen. 
NOTE    ► Allowing the proper amount of space on the top, sides, and rear of the 
projector cabinet is critical for proper air circulation and cooling of \
the unit. When in 
against at wall, leave about 20cm (7.9in.) between the projector and t\
he wall.   
Screen size (diagonal)
Projection distance 
Screen height 
M
D
H
On a horizontal surfaceSuspended from the ceiling
M
M
D
HH
Lens center
Screen
Side view
M 
						

							
7
Setting up
WARNING 
• Place the projector in a stable horizontal position. 
If the projector falls or is knocked over it could cause injury and/or d\
amage 
to the projector. Using a damaged projector could then result in fire and/or 
electric shock.
(1) Do not place the projector on an unstable, slanted or vibrational \
surface 
      such as a wobbly or inclined stand.
(2) Do not place the projector on its side, front or rear position. 
(3) Consult with your dealer before a special installation such as sus\
pending
      from a ceiling.
• Place the projector in a cool place, and ensure that there is sufficient 
ventilation. The high temperature of the projector could cause fire, burns and
/or malfunction of the projector.
(1) Do not stop-up, block or otherwise cover the projectors vents.Kee\
p a 
     space of 20 cm or more between the sides of the projector and other\
 
     objects such as walls.
(2) Do not place the projector on metallic thing or anything weak in h\
eat. 
(3) Do not place the projector on carpet, cushions or bedding. 
(4) Do not place the projector in direct sunlight or near hot objects \
such as 
     heaters. 
(5) Do not place anything near the projector lens or vents, or on top \
of the 
     projector. 
(6) Do not place anything that may be sucked into or stick to the vent\
s on 
     the left of the projector. This projector has some intake vents also on the 
     left.
• Avoid placing the projector in smoky, humid or dusty place.
• Do not place the projector anyplace where it may get wet. Getting t\
he
projector wet or inserting liquid into the projector could cause fire, electric 
shock and/or malfunction of the projector.
(1) Do not place the projector in a bathroom or the outdoors.
(2) Do not place anything containing liquid near the projector.  
 
 
 
 
 
CAUTION
Placing the projector in such places could cause fire, electric shock and/or
malfunction of the projector.
(1) Do not place the projector near humidifiers, smoking spaces or a kitchen.
(2) Position the projector to prevent light from directly hitting the \
projectors 
remote sensor.   
						

							
8
Setting up
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector
Make sure that all the devices are suitable to be connected with this pr\
oduct, and 
prepare the cables required to connect. Please refer to the following illustrations 
to connect them.
PC
          LANS (Optional Function)Audio outMonitor inMonitor inRS-232CUSBAudio out
Audio out
VGA outDVI outVGA out
VCD/DVD PlayerSpeaker
Audio out (L)&(R)Audio out (L)&(R)Video outS-video outYPb/CbPr/Cr 
						

							
9
Setting up
Connecting your devices(Continue)
WARNING ►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
CAUTION ►Turn off all devices and unplug their power cords prior to 
connecting them to projector. Connecting a live device to the projector may 
generate extremely loud noises or other abnormalities that may result in 
malfunction or damage to the device and the projector.
►Use appropriate accessory or otherwise designed cables. Ask your dealer
about non-accessory cables which may have other length or equipped with 
a core. For cables with a core only at one end, connect the end with the core 
to the projector.    
►Make sure that devices are connected to the correct ports. An incorrect 
connection may result in malfunction or damage to the device and the 
projector.  
NOTE  ►Be sure to read the manuals for devices before connecting them to the 
projector, and make sure that all the devices are suitable to be connected with this 
product. Before connecting to a PC, check the signal level, the signal timing, and the 
resolution.
- Some signal may need an adapter to input this projector.
- Some PCs have multiple screen display modes that may include some signals which
  are not supported by this projector.
-The best display performance will be achieved if the resolutions of the input signal 
and the projector panel are identical.
►While connecting, make sure that the shape of the cable's connector fits the port to 
connect with. And be sure to tighten the screws on connectors with screws.
►When connecting a laptop PC to the projector, be sure to activate the PC’s external 
monitor(RGB) output. (Set the laptop PC to CRT display or to simultaneous LCD and 
CRT display.) For details on how this is done, please refer to the instruction manual of 
the corresponding laptop PC.
►In some cases, this projector may not display a proper picture or display any picture 
on screen. For example, automatic adjustment may not function correctly with some 
input signals. An input signal of composite sync may confuse this projector, so the 
projector may not display a proper picture.  
						

							
10
Setting up
Connecting power supply
WARNING
►Please use extra caution when connecting the power cord, as incorrect or 
    faulty connections may result in fire and/or electrical shock.
►Only use the power cord that came with the projector. If it is damaged, 
    contact your dealer soon.
►Only plug the power cord into an outlet rated for use with the power cord's 
    specified voltage range. The power outlet should be close to the projector 
    and easily accessible. Remove the power cord for complete separation.
►Never modify the power cord. 
Using the Security Anchor
WARNING
►Do not use the security anchor to prevent the projector from falling down or 
held, since it is not designed for it.
NOTE ►The security anchor is not comprehensive theft prevention measures. 
It is intended to be used as supplemental theft prevention measure.
OutletAC inlet
1.Connect the connector of the power cord
     to the AC inlet of the projector. 
2.Firmly plug the power cable’s plug into 
    the outlet.The POWER indicator will 
    begin blinking in green.The projector 
    work on stand by mode.
POWER indicator
Security Anchor
The product has design security 
anchor and PIN LOCK functions 
(SEE P31)to help prevent 
unauthorized removal projector.