Bosch WVD 24420 User Manual

51
Consumption values 
Normal programme Additional 
optionLoad Consumption values**  Programme 
duration
Power Water
Cottons 40 °C_ 5 kg 0.46 kWh  51.6 l 1:08 h 
Cottons 60 °C_ 5 kg 1.02 kWh  51.5 l 1:25 h 
Cottons Eco 60 °C Intensive
È* 5 kg 0.90 kWh 44.9 l 2:10 h 
Cottons 90 °C
(the hot washing solution is mixed 
with approx.7 litres of cold water 
before being drained)_ 5 kg 1.72 kWh  58.6 l 1:50 h 
Delicate/Silk 30 °C_ 2 kg 0.32 kWh  39 l 0:37 h 
Ï
 Wool l  30 °C_ 2 kg 0.17 kWh  33.1 l 0:41 h...

52
Customer service 
Before you call customer service, please check 
whether you can eliminate the fault yourself (see from 
page 47). 
A technician who is called out to give advice will 
charge you, even if the appliance is still under 
guarantee. 
You can find your nearest customer service in the 
enclosed address list. Please provide customer 
service with the product number (E-Nr.) and the 
production number (FD) of the appliance. 
These numbers are shown on the rating plate which 
can be found on...

53
Installation instructions
Installing, connecting and transporting 
Safety instructions mRisk of injury! 
The washer-dryer is heavy. Take care when lifting it. 
Caution                                                                            
Frozen hoses may tear/burst. Do not install the 
washer-dryer in an area where there is a risk of frost or 
outdoors. 
The washer-dryer may be damaged. Do not lift the 
washer-dryer by its projecting parts (e. g. door). 
In addition to the safety information...

54
Useful tools The following tools are helpful: 
– Box wrench A/F 13 for removing the transportation 
bolts. 
– Spirit level for aligning the washer-dryer. 
Dimensions a = 600 mm 
b = 560 mm 
c = 850 mm 
Weight 67 kg 
Installation surface Appliance stability is important so that the washer-dryer 
does not wander during the spin cycles. 
The installation surface must be solid and level. Soft 
floor coverings, e. g. carpets or floor coverings with a 
foam backing are not suitable. 
If the washer-dryer is...

55
Removing the 
transportation 
protection devices mCaution 
The transport bolts must always be removed before 
using the appliance for the first time and must be 
retained for any subsequent transport (e.g. when 
moving). 
■Release all screws A using the A/F 13 wrench until 
they can be moved freely.
■Remove the four spacers. They will fall to the floor 
when you tip the machine.
■Insert the covers. 
B
A
D
C
 

56
Built-under or built-in 
appliance installation The appliance must be built under or built in prior to 
connecting the power supply. 
The appliance can be built into or under a kitchen work 
surface. For this purpose, a recess width of 60 cm is 
required. 
■The washer-dryer must only be installed under a 
one-piece worktop that is permanently attached to 
the surrounding cabinets. 
Caution                                                                            
For safety reasons in built-under...

57
Hose and cable 
lengths 
Connection on left side 
Connection on right side 
Other hoses Available from specialist dealers: 
– Extended supply hose (approx. 2.20 m). 
mcmax.100mcmax.100
110cm~
~
100cm~
~
110cm~
~
mcmax.100mcmax.100
150cm~
~
140cm~
~
150cm~
~
 

58
Connecting the water mRisk of electric shock! 
To prevent leaks or water damage, it is essential to fol-
low the instructions in this chapter! 
Water inlet hose  Caution                                                                            
Operate the washer-dryer with cold drinking water only. 
Do not connect to the mixer tap of an unpressurised 
hot-water apparatus. 
If in doubt, have the appliance connected by a special-
ist. 
Do not use a used inlet hose. Only use the inlet hose 
supplied or...

59
Water drainage hose mWarning
Do not bend or pull the water drainage hose. 
Height difference between the placement area and 
drainage point: maximum 100 cm. 
Drainage into a siphon: 
■Secure connection point with 24-40 mm Ø hose 
clip (specialist outlet). 
Drainage into a wash basin: 
Caution                                                                            
The plug must not block the drain of the wash basin. 
■Secure the drainage hose to prevent it from 
slipping out of the sink. 
■When the...

60
Connecting the power mCaution 
Connect the washer-dryer only to an alternating current 
via a correctly installed earthed socket. 
The mains voltage must correspond to the voltage 
specification on the washer-dryer (nameplate). Con-
nection specifications as well as the required fuses are 
stipulated on the appliance nameplate. 
Ensure that: 
– The mains plug and socket are compatible. 
– The cable cross-section is adequate. 
– The earthing system has been installed correctly. 
The mains cable may be...