Bosch WVD 24420 User Manual

							51
Consumption values 
Normal programme Additional 
optionLoad Consumption values**  Programme 
duration
Power Water
Cottons 40 °C_ 5 kg 0.46 kWh  51.6 l 1:08 h 
Cottons 60 °C_ 5 kg 1.02 kWh  51.5 l 1:25 h 
Cottons Eco 60 °C Intensive
È* 5 kg 0.90 kWh 44.9 l 2:10 h 
Cottons 90 °C
(the hot washing solution is mixed 
with approx.7 litres of cold water 
before being drained)_ 5 kg 1.72 kWh  58.6 l 1:50 h 
Delicate/Silk 30 °C_ 2 kg 0.32 kWh  39 l 0:37 h 
Ï
 Wool l  30 °C_ 2 kg 0.17 kWh  33.1 l 0:41 h 
Easy-Care = 40 °C_ 2,5 kg 0.34 kWh  33.8 l 0:50 h 
Jeans 30 °C_ 2,5 kg 0.32 kWh  52.1 l 1:06 h 
Sensitive s 40 °C_ 5 kg 0.81 kWh  73.5 l 1:23 h 
Sport, Fitness
]] 30 °C_ 2,5 kg 0.21 kWh  38.6 l 0:41 h 
Super 15’ 30 °C_ 2 kg 0.21 kWh  34.8 l 0:15 h 
Mix 40 °C_ 2,5 kg 0.60 kWh  36.2 l 0:50 h 
Intensive Dry Š_ 2,5 kg 1.83 kWh  30.6 l 1:51 h 
Gentle Dry ‰_ 1,5 kg 1.16 kWh  29 l 1: 27 h 
Cottons Eco 60 °C + Intensive Dry 
Š (2 auto drying cycles)Intensive
È* 5 kg 4.56 kWh 106 l 5:52 h 
(2:10 h 
+3:42 h)
* Programme setting with Intensive È* option for test in accordance or in conformity with EN 50 229 and 
IEC 50 229. 
**  Consumption values will  differ from the indicated values depending on the water pressure, water hardness, 
water inlet temperature, ambient temperature, type and quantity of laundry and degree of soiling, utilised 
detergent, fluctuations in the mains voltage and selected additional options. 
 
						

							52
Customer service 
Before you call customer service, please check 
whether you can eliminate the fault yourself (see from 
page 47). 
A technician who is called out to give advice will 
charge you, even if the appliance is still under 
guarantee. 
You can find your nearest customer service in the 
enclosed address list. Please provide customer 
service with the product number (E-Nr.) and the 
production number (FD) of the appliance. 
These numbers are shown on the rating plate which 
can be found on the frame of the open door and also 
on the identification plate, enclosed by a thick line, on 
the front of the machine behind the nameplate. 
Please note the two numbers in the space provided 
above.
In specifying the product number and production 
number of your appliance, you help us in our attempt 
to prevent unnecessary travelling and the associated 
extra costs.
Rating plate
E-Nr.FD
Product number Production number
 
						

							53
Installation instructions
Installing, connecting and transporting 
Safety instructions mRisk of injury! 
The washer-dryer is heavy. Take care when lifting it. 
Caution                                                                            
Frozen hoses may tear/burst. Do not install the 
washer-dryer in an area where there is a risk of frost or 
outdoors. 
The washer-dryer may be damaged. Do not lift the 
washer-dryer by its projecting parts (e. g. door). 
In addition to the safety information listed here, the 
local water and electricity supplier may have special 
requirements. 
If in doubt, have the appliance connected by a 
specialist. 
Standard accessories – Water drainage hose
– Water-inlet hose. 
– Elbow for attaching the drainage hose e.g.  to the 
sink. 
– Power cord. 
Moisture in the drum is due to the final inspection 
which every washer-dryer undergoes before it leaves 
the factory. 
Depending on the connection situation, the following 
part is also required: 
– 1 hose clip 
Ø 24-40 mm (DIY store) is also 
required for connection to a siphon. 
The bag contains: 
– Covers for holes left by removing the transport 
bolts. 
 
						

							54
Useful tools The following tools are helpful: 
– Box wrench A/F 13 for removing the transportation 
bolts. 
– Spirit level for aligning the washer-dryer. 
Dimensions a = 600 mm 
b = 560 mm 
c = 850 mm 
Weight 67 kg 
Installation surface Appliance stability is important so that the washer-dryer 
does not wander during the spin cycles. 
The installation surface must be solid and level. Soft 
floor coverings, e. g. carpets or floor coverings with a 
foam backing are not suitable. 
If the washer-dryer is to be installed on a wooden floor: 
■If possible, install the washer-dryer in a corner. 
■Screw a water-resistant wooden board (at least 30 
mm thick) to the floor. 
■Secure the washer-dryer feet with fixing brackets*. 
If the washer-dryer is to be installed on a base: 
■Secure the washer-dryer feet with fixing brackets*. 
*  Holding brackets (set) can be obtained from a 
specialist store or the Customer Service, 
order no. WMZ 2200. 
 
						

							55
Removing the 
transportation 
protection devices mCaution 
The transport bolts must always be removed before 
using the appliance for the first time and must be 
retained for any subsequent transport (e.g. when 
moving). 
■Release all screws A using the A/F 13 wrench until 
they can be moved freely.
■Remove the four spacers. They will fall to the floor 
when you tip the machine.
■Insert the covers. 
B
A
D
C
 
						

							56
Built-under or built-in 
appliance installation The appliance must be built under or built in prior to 
connecting the power supply. 
The appliance can be built into or under a kitchen work 
surface. For this purpose, a recess width of 60 cm is 
required. 
■The washer-dryer must only be installed under a 
one-piece worktop that is permanently attached to 
the surrounding cabinets. 
Caution                                                                            
For safety reasons in built-under installation, a cover 
plate* must be assembled by a specialist in place of 
the appliance cover plate. 
*  Cover plate (set) can be obtained from a specialist 
store or the Customer Service, order no.
WMZ 2420. 
 
						

							57
Hose and cable 
lengths 
Connection on left side 
Connection on right side 
Other hoses Available from specialist dealers: 
– Extended supply hose (approx. 2.20 m). 
mcmax.100mcmax.100
110cm~
~
100cm~
~
110cm~
~
mcmax.100mcmax.100
150cm~
~
140cm~
~
150cm~
~
 
						

							58
Connecting the water mRisk of electric shock! 
To prevent leaks or water damage, it is essential to fol-
low the instructions in this chapter! 
Water inlet hose  Caution                                                                            
Operate the washer-dryer with cold drinking water only. 
Do not connect to the mixer tap of an unpressurised 
hot-water apparatus. 
If in doubt, have the appliance connected by a special-
ist. 
Do not use a used inlet hose. Only use the inlet hose 
supplied or one which was purchased from an autho-
rised specialist dealer. 
The water inlet hose must not be 
– kinked or crushed, 
– modified or severed (strength is no longer guaran-
teed). 
Plastic threads must only be tightened by hand. Do not 
remove the strainers from the water supply hose. 
Check the mains water pressure: 
– The water pressure should be between 1 and 10 
bars (when the tap is turned on, at least 8 litres of 
water is discharged per minute). 
– If the water pressure is higher, install a pressure 
reducing valve. 
Connect the water supply hose 
■to the rear panel of the washer-dryer and ... 
■to the tap. 
■After connecting the water inlet hose: Turn on the 
water tap completely, and check connection points 
for water-tightness. 
■
min. 10 mm
 
						

							59
Water drainage hose mWarning
Do not bend or pull the water drainage hose. 
Height difference between the placement area and 
drainage point: maximum 100 cm. 
Drainage into a siphon: 
■Secure connection point with 24-40 mm Ø hose 
clip (specialist outlet). 
Drainage into a wash basin: 
Caution                                                                            
The plug must not block the drain of the wash basin. 
■Secure the drainage hose to prevent it from 
slipping out of the sink. 
■When the water is being pumped out of the 
washer-dryer, check that the water drains away 
quickly enough. 
Aligning the washer-
dryer All four appliance feet must be firmly on the ground. 
The washer-dryer must not wobble. 
Level the washer-dryer with the assistance of the four 
adjustable feet and a spirit level: 
■Loosen the lock nut 1 using the wrench. 
■Adjust the height by rotating the foot 2. 
■Tighten the lock nut 1 against the housing. 
 
						

							60
Connecting the power mCaution 
Connect the washer-dryer only to an alternating current 
via a correctly installed earthed socket. 
The mains voltage must correspond to the voltage 
specification on the washer-dryer (nameplate). Con-
nection specifications as well as the required fuses are 
stipulated on the appliance nameplate. 
Ensure that: 
– The mains plug and socket are compatible. 
– The cable cross-section is adequate. 
– The earthing system has been installed correctly. 
The mains cable may be changed (if required) by an 
electrician only. 
Replacement mains cable available from Customer 
Service. 
Do not use multiple plugs/sockets or extension cables. 
In the event that an earth-leakage circuit breaker is to 
be used, only use types marked with the following sym-
bol: z
Only this symbol can guarantee compliance with all 
current regulations.
Do not insert/pull out the mains plug with wet hands. 
Do not pull out the mains plug by tugging the cable.