Bosch Tech 2 User Manual

Getting Started
Te c h  2Page 3-19
FIGURE 3-27. Tech 2 Start-Up Screen 

Getting Started
Page 3-20Te c h  2 

Te c h  2Page 4-1
4.  POWER SUPPLIES
Power up the Tech 2 using either: 
• The power jack connector at the bottom of the Tech 2 unit (Figure 4-1), or 
• The DLC cable power jack connector behind the area where various DLC adapters are connected 
(Figure 4-1). 
For non-vehicle communications, connect the power source to either location. 
For vehicle communications, connect the power source to the DLC cable power jack connector only. Proper 
grounding may not be present if the power source is connected...

Power Supplies
Page 4-2Te c h  2
BATTERY POWER CABLE 
This cable has red and black battery clamps attached to one end and a power jack to the other (Figure 4-1). 
The power jack connects to the Tech 2 DLC cable and carries current to the Tech 2 when the selected 
vehicle adapter does not provide power and there is no cigarette lighter adapter available.
NOTE
This cable contains two 3-amp fuses. If you need to replace them, use 
identical 3-amp fuses. See Chapter 6 for information on fuse replacement....

Power Supplies
Te c h  2Page 4-3
NAO POWER SUPPLY 
North American electrical supply is normally 110 volts. The Tech 2 base kit includes an external AC to DC 
power supply with 110 V AC/60 Hz input (Figure 4-2). Output is 12 volts at 1.5 amps.
CAUTION
CAUTION!To avoid personal injury due to electric shock, use a grounded outlet only. 
The NAO power supply is for North American use only. These devices are 
intended for indoor use only.
FIGURE 4-2. NAO Power Supply (110 Volts) 

Power Supplies
Page 4-4Te c h  2 

Te c h  2Page 5-1
5.  ADAPTERS
A number of adapters are available for the Tech 2 which allow connection to many different vehicles 
(Ta b l e 5 - 1 ,  Tech 2 Adapters). Specific adapters are included in the Tech 2 base kit depending upon Tech 2 
configuration
—NAO. Adapters not included in the base kit may be purchased separately from Vetronix. 
DLC CABLE 
The DLC cable (P/N 02002952) has a 26-pin connector with thumb screws at one end that connects to the 
Tech 2s VCI cable connector. At the other end...

Adapters
Page 5-2Te c h  2
RS-232 CABLE 
The RS-232 cable (P/N 02001358) has an 8-pin RJ45 plug connector at each end (Figure 5-2). This cable 
attaches to the Tech 2 RS-232 port and is used to communicate with a PC. 
Description FunctionGM Part 
Numbers
 SAE 16/19 Pin Adapter  This adapter allows DLC connection to some 1994-
1995 NAO vehicles and all NAO vehicles from 1996 
onward. 02002955
NAO 12/19 Pin Adapter This adapter allows ALDL connection to some 1994-
1995 NAO vehicles and all previous 1993...

Adapters
Te c h  2Page 5-3
RS-232/DB9 ADAPTER 
The RJ45/BB9 adapter (P/N 02001030) has an RJ45 connector at one end and a DB9 connector at the other 
(Figure 5-3). This adapter allows the connection of the Tech 2 to a PC. 
RS-232 LOOPBACK ADAPTER 
The loopback adapter (P/N 02001606) has an 8-pin RJ45 connector that attaches to the Tech 2 RS-232 port 
(Figure 5-3). It is used to perform the Tech 2 self test.
FIGURE 5-3. RS-232/DB9 Adapter Connections RS-232 cable connected to Tech 2 
8-Pin RJ45 connector...

Adapters
Page 5-4Te c h  2