Bosch Tech 2 User Manual

Getting Started
Te c h  2Page 3-9
TECH 2 KEYPAD 
The Tech 2 keypad consists of six major keypad operation areas: 
FIGURE 3-14. Tech 2 KeypadSoft keys 
Action keys
Control keys 
Help key  Function keys (F0 - F9) Selection (arrow) keys 
(YES, NO, 
ENTER, EXIT) 
(SHIFT, PWR)  

Getting Started
Page 3-10Te c h  2
CONTROL KEYS 
The [PWR] key is used to turn the Tech 2 on or off (Figure 3-15). The status indicator light above this key is 
illuminated green when the Tech 2 is operational. 
The [SHIFT] key is used with the up and down arrow keys to change screen brightness and contrast 
(Figure 3-15).
To adjust screen brightness and contrast, perform the following: 
1. Press the [SHIFT] key once (amber status indicator light above [SHIFT] lights up). 
2. Use up and down arrows to...

Getting Started
Te c h  2Page 3-11
TECH 2 SOFT KEYS 
Four soft keys are located directly below the Tech 2 screen (Figure 3-16). The soft keys correspond directly 
to the four possible selection boxes found at the bottom region of the Tech 2 screen. These selections may 
change from screen to screen and are under the control of the application software. To make a screen 
selection, press the corresponding soft key. In the example shown in Figure 3-17, the first soft key was 
pressed to select [Display...

Getting Started
Page 3-12Te c h  2
SELECTION KEYS 
The Tech 2 selection keys are four directional arrow keys (Figure 3-18). The arrow keys are pressed to move 
the highlighted area to a selection on the screen (Figure 3-19) or to scroll the screen if there is more than one 
screen. Once the desired selection is highlighted, press [ENTER] to activate the selection. 
FIGURE 3-18. Location of Selection Keys
FIGURE 3-19. Positioning Highlighted Area to Make a SelectionHighlighted area 
Bottom [ENTER] key...

Getting Started
Te c h  2Page 3-13
ACTION KEYS 
Action keys are used to respond to a specific question, initiate an action, or to exit from the Tech 2 program 
(Figure 3-20). Specific yes or no questions often appear on the Tech 2 screen. The [YES] and [NO] keys 
are used to respond to these questions. Either of the two [ENTER] keys may be pressed to activate a menu 
selection. Either of the two [EXIT] keys may be pressed to leave the current Tech 2 screen and return to a 
previous screen. 
FIGURE 3-20....

Getting Started
Page 3-14Te c h  2
FUNCTION KEYS 
Ten function keys (F0 to F9) are located on the Tech 2 keypad (Figure 3-21). A function key may be pressed 
to initiate a specific Tech 2 function. In some cases the function keys are used for numeric data entry. The 
arrow keys and [ENTER] may also be used to initiate a function selection, however, this may require 
additional keystrokes. 
FIGURE 3-21. Location of Function Keys 

Getting Started
Te c h  2Page 3-15
HELP KEY 
The [?] key (Figure 3-22) may be pressed at any time to obtain a help screen. The help screen provides 
specific information relating to the operation of the Tech 2. 
FIGURE 3-22. Location of Help Key 

Getting Started
Page 3-16Te c h  2
TECH 2 CONNECTIONS TO VEHICLE 
The Tech 2 receives power through the DLC cable connection to vehicles equipped with On-Board 
Diagnostics (OBD II) (Figure 3-23). In the case of vehicles not equipped with OBD II, an external power 
source such as a vehicle cigarette lighter must be used (Figure 3-24). 
FIGURE 3-23. Attaching the Tech 2 to OBD II-Equipped Vehicles DLC cable connector  SAE 16/19 pin adapter
(P/N 02002955) 
FIGURE 3-24. Attaching the Tech 2 to Non-OBD...

Getting Started
Te c h  2Page 3-17
TECH 2 CONNECTION TO PC 
It may be necessary to connect the Tech 2 with a PC for the following reasons: 
• Transfer of vehicle data (calibration information, snapshot, etc.) from the Tech 2 to the PC 
• Transfer of vehicle calibration data from the PC to the Tech 2 
• Transfer of data (software update, etc.) from the PC to the Tech 2 
• Before connecting Tech 2 to the PC, the following steps should be taken: 
• Make sure that the RS-232 cable (P/N 02001358) is attached...

Getting Started
Page 3-18Te c h  2
FIGURE 3-26. Tech 2 Connection to PC1Serial port adapter
Appropriate power supply 
Power jack (plugged into Tech 2 RS-232 communications cable(P/N 02001030) 
(P/N 02001358) 
power jack connector)