Bosch Rotak 32 R Manual

							Robert Bosch GmbH
Power Tools Division
70764 Leinfelden-Echterdingen
GERMANY
www.bosch-garden.com
F 016 L81 164 (2014.11) O / 12 XXX  
Rotak 32enOriginal instructions
OBJ_DOKU-24112-005.fm  Page 1  Wednesday, November 19, 2014  2:32 PM 
						

							2 | English 
F 016 L81 164 | (19.11.14)Bosch Power Tools
English
Safety Notes
Warning! Read these instructions 
carefully, be familiar with the con-
trols and the proper use of the ma-
chine. Please keep the instructions 
safe for later use!
Explanation of symbols
General hazard safety alert.
Read instruction manual.
Pay attention that bystanders 
are not injured through foreign 
objects thrown from the ma-
chine.
Warning: Keep a safe distance 
from the machine when operat-
ing.
Caution: Do not touch rotating 
blades. Sharp blade(s). Beware 
of severing toes or fingers.
Switch off and remove plug 
from mains before adjusting, 
cleaning or if the cable is entan-
gled and before leaving the garden 
product unattended for any period. 
Keep the supply flexible cord away 
from the cutting blades.
Not applicable.Wait until all machine compo-
nents have completely stopped 
before touching them. The 
blades continue to rotate after the ma-
chine is switched off, a rotating blade 
can cause injury.
Do not use the machine in the 
rain or leave it outdoors when it 
is raining.
Beware electric shock hazard.
Keep supply flexible cord away 
from cutting means.
Operation
Never allow children or people unfa-
miliar with these instructions to use 
the machine. Local regulations may 
restrict the age of the operator. When 
not in use store the machine out of 
reach of children.
This machine is not intended for use 
by persons (including children) with 
reduced physical, sensory or mental 
capabilities, or lack of experience and 
knowledge, unless they have been 
given supervision or instruction con-
cerning use of the machine by a per-
son responsible for their safety.
Children should be supervised to en-
sure that they do not play with the 
machine.
Never mow while people, especially 
children, or pets are nearby.
The operator or user is responsible 
for accidents or hazards occurring to 
other people or their property.
OBJ_BUCH-1349-005.book  Page 2  Wednesday, November 19, 2014  2:33 PM 
						

							 English | 3
Bosch Power ToolsF 016 L81 164 | (19.11.14)
Do not operate the machine when 
barefoot or wearing open sandals, al-
ways wear substantial footwear and 
long trousers.
Thoroughly inspect the area where 
the machine is to be used and remove 
all stones, sticks, wires, bones and 
other foreign objects.
Before using, always visually inspect 
to see that the blades, blade bolts 
and cutter assembly are not worn or 
damaged. Replace worn or damaged 
blades and bolts in sets to preserve 
balance.
Mow only in daylight or in good artifi-
cial light.
Avoid mowing in bad weather condi-
tions especially when there is a risk of 
lightning.
Avoid operating the machine in wet 
grass, where feasible.
Walk, never run.
Never operate the appliance with de-
fective guards or shields, or without 
safety devices, for example deflec-
tors and/or grass catchers in place.
Working on banks can be dangerous.
– Do not mow on excessively steep 
slopes.
– Always be sure of your footing on 
slopes or wet grass.
– Mow across the face of slopes –  nev-
er up and down.
– Exercise extreme caution when 
changing direction on slopes.
Use extreme caution when stepping 
back or pulling the machine towards 
you.
Never mow by pulling the mower to-
wards you.
Stop the blades if the machine has to 
be tilted for transportation when 
crossing surfaces other than grass 
and when transporting the machine 
to and from the area to be mowed.
Do not tilt the machine when starting 
or switching on the motor, except if 
the machine has to be tilted for start-
ing in long grass. In this case, do not 
tilt it more than absolutely necessary 
and tilt only the part which is away 
from the operator. Always ensure 
that both hands are in the operating 
position before returning the ma-
chine to the ground.
Switch on the motor according to the 
instructions with feet well away from 
rotating parts.
Do not put hands or feet near or un-
der rotating parts.
Always stand clear of the discharge 
zone when operating the machine.
Never pick up or carry the machine 
while the motor is running.
Do not modify this product. Unau-
thorized modifications may impair 
the safety of your product and may 
result in increased noise and vibra-
tion.
Regularly inspect the supply cable 
and any extension cables. Do not con-
nect damaged cables to the supply or 
touch a damaged cable before it is 
disconnected from the supply. A 
damaged cable can lead to contact 
with live parts. Beware electric shock 
hazard.
OBJ_BUCH-1349-005.book  Page 3  Wednesday, November 19, 2014  2:33 PM 
						

							4 | English 
F 016 L81 164 | (19.11.14)Bosch Power Tools
Remove the plug from the socket:
– Whenever you leave the machine.
– before clearing a blockage,
– before checking, cleaning or working 
on the machine,
– after striking a foreign object. Inspect 
the machine for damage and make re-
pairs as necessary,
– if the machine starts to vibrate abnor-
mally (check immediately).
Connecting to the mains
The voltage indicated on the rating 
plate must correspond to the voltage 
of the power source.
We recommend that this equipment 
is only connected into a socket which 
is protected by a circuit-breaker that 
would be actuated by a 30 mA residu-
al current.
Only use or replace power supply ca-
bles for this unit which correspond to 
the types indicated by the manufac-
turer. See the operating instructions 
for the order no. and types.
Never touch the mains plug with wet 
hands.
Do not run over, crush or pull the 
power supply cord or extension cord, 
otherwise it may be damaged. Pro-
tect the cable from heat, oil and sharp 
edges.
The extension lead must have a cross 
section in accordance with the oper-
ating instructions and be protected 
against splashed water. The connec-
tion must not be in water.
Always wear gardening gloves when 
handling or working near the sharp 
blades.
Electrical Safety
Warning! Switch off, remove plug 
from mains before adjusting, 
cleaning or if cable is cut, damaged 
or entangled.
The blades continue to rotate for a 
few seconds after the machine is 
switched off.
Caution  –  do not touch the rotating 
blade.
Your machine is double insulated for 
safety and requires no earth connec-
tion. The operating voltage is 230 V AC, 
50 Hz (for non-EU countries 220 V, 
240 V as applicable). Only use ap-
proved extension cables. Contact your 
Bosch Service Centre for details.
Extension cords/leads should only be 
used if they comply with H05VV-F, 
H05RN-F types or IEC type design 
(60227 IEC 53, 60245 IEC 57).
If you want to use an extension cable 
when operating your product, only the 
following cable dimensions should be 
used:
– 1.0 mm
2: max. length 40 m
– 1.5 mm
2: max. length 60 m
– 2.5 mm
2: max. length 100 m
Note: If an extension cable is used it 
must be earthed and connected 
through the plug to the earth cable of 
your supply network in accordance 
with prescribed safety regulations.
OBJ_BUCH-1349-005.book  Page 4  Wednesday, November 19, 2014  2:33 PM 
						

							 English | 5
Bosch Power ToolsF 016 L81 164 | (19.11.14)
If in doubt contact a qualified electri-
cian or the nearest Bosch Service Cen-
tre.
WARNING! Inadequate extension 
cables can be dangerous. Exten-
sion cable, plug and socket must be 
of watertight construction and in-
tended for outdoor use.
Cable connections should be kept dry 
and off the ground.
It is recommended for increased elec-
trical safety to use a Residual Current 
Device (RCD) with a tripping current of 
not more than 30 mA. Always check 
your RCD every time you use it.
For products not sold in GB:
WARNING: For your safety, it is re-
quired that the plug attached to the ma-
chine is connected with the extension 
cord. The coupling of the extension 
cord must be protected against splash 
water, be made of rubber or coated 
with rubber. The extension cord must 
be used with a cable strain relief.
The connection lead must be inspected 
for signs of damage at regular intervals 
and may only be used if in perfect con-
dition.
If the supply cord is damaged, it must 
be replaced by a Bosch Service Centre.
Products sold in GB only: Your prod-
uct is fitted with a BS 1363/A approved 
electric plug with internal fuse (ASTA 
approved to BS 1362).
If the plug is not suitable for your socket 
outlets, it should be cut off and an ap-
propriate plug fitted in its place by an 
authorised customer service agent. 
The replacement plug should have the 
same fuse rating as the original plug.The severed plug must be disposed of 
to avoid a possible shock hazard and 
should never be inserted into a mains 
socket elsewhere.
Products sold in AUS and NZ only: 
Use a residual current device (RCD) 
with a rated residual current of 30 mA 
or less.
Maintenance
Always wear gardening gloves 
when handling or working near the 
sharp blades.
Keep all nuts, bolts and screws tight 
to be sure that the machine is in safe 
working condition.
Check the grass catcher frequently 
for wear or deterioration.
Examine the machine and replace 
worn or damaged parts for safety.
Ensure replacement cutting means of 
the right type are used.
Ensure replacement parts fitted are 
Bosch approved.
Before storage ensure machine is 
clean and free from debries, if neces-
sary clean with a soft, dry brush.
Symbols
The following symbols are important for reading and under-
standing the operating instructions. Please take note of the 
symbols and their meaning. The correct interpretation of the 
symbols will help you to use the garden product in a better 
and safer manner.
SymbolMeaning
Movement direction
Reaction direction
OBJ_BUCH-1349-005.book  Page 5  Wednesday, November 19, 2014  2:33 PM 
						

							6 | English 
F 016 L81 164 | (19.11.14)Bosch Power Tools
Intended Use
The garden product is intended for domestic lawnmowing.
Technical Data
Noise/Vibration Information
Sound emission values determined according to 
EN 60335-2-77.
Typically the A-weighted noise levels of the product are: 
Sound pressure level 79 dB(A); sound power level 93 dB (A). 
Uncertainty K = 1 dB.
Vibration total values a
h (triax vector sum) and uncertainty K 
determined according to EN 60335:
a
h
						

							 English | 7
Bosch Power ToolsF 016 L81 164 | (19.11.14)
Troubleshooting
After-sales Service and Application 
Service
www.bosch-garden.com
In all correspondence and spare parts orders, please always 
include the 10-digit article number given on the type plate of 
the garden product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange 
the collection of a product in need of servicing or repair. 
Tel. Service: (0344) 7360109
E-Mail: [email protected]
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888

ProblemPossible CauseCorrective Action
Motor refuses to start Power turned off Turn power on
Mains socket faulty Use another socket
Extension cable damaged Inspect cable, replace if damaged
Fuse faulty / blown Replace fuse
Possible clogging Check underneath the garden product and 
clear out as necessary (always wear protective 
gloves)
Motor protector has activated Allow motor to cool and increase height of cut
Mowing too low for the conditions Increase height of cut
Machine functions 
intermittentlyExtension cable damaged Inspect cable, replace if damaged
Internal wiring of machine damaged Contact Service Agent
Motor protector has activated Allow motor to cool and increase height of cut
Machine leaves ragged finish
and/or
Motor laboursHeight of cut too low Increase height of cut
Cutting blade blunt Replace the blade
Possible clogging Check underneath the garden product and 
clear out as necessary (always wear protective 
gloves)
Blade fitted upside down Refit blade correctly
Blade not rotating while garden 
product switched onCutting blade obstructed Switch off garden product
Clear obstruction (always wear protective 
gloves)
Blade nut/bolt loose Tighten blade nut/bolt (17 Nm)
Excessive vibrations/noise Blade nut/bolt loose Tighten blade nut/bolt (17 Nm)
Cutting blade damaged Replace the blade
OBJ_BUCH-1349-005.book  Page 7  Wednesday, November 19, 2014  2:33 PM 
						

							8 | English 
F 016 L81 164 | (19.11.14)Bosch Power Tools
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: [email protected]
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: [email protected]
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
E-Mail: [email protected]
Bosch Headquarters
Midrand, Gauteng
Tel.: (011) 6519600
Fax: (011) 6519880
E-Mail: [email protected]
Do not dispose of garden products into household waste!
Only for EC countries:
According to the European directive 
2012/19/EU for Waste Electrical and Elec-
tronic Equipment and its implementation into 
national law, electrical and electronic equip-
ment that are no longer usable must be col-
lected separately and disposed of in an envi-
ronmentally correct manner.
Subject to change without notice.
OBJ_BUCH-1349-005.book  Page 8  Wednesday, November 19, 2014  2:33 PM 
						

							  | 9
Bosch Power ToolsF 016 L81 164 | (19.11.14)
STOP
CLICK!
1
2
3
7,0 kg
1x
1x
1x 2x 2x 2x
OBJ_BUCH-1349-005.book  Page 9  Wednesday, November 19, 2014  2:33 PM 
						

							F 016 L81 164 | (19.11.14)Bosch Power Tools
10 |  
1 2
460 
mm
40  mm
20  mm
5
OBJ_BUCH-1349-005.book  Page 10  Wednesday, November 19, 2014  2:33 PM