Bosch 540 De Manual

EURO ¥ Printed in Germany ¥ BA 1 619 929 535 ¥ GBH 5-40 DE ¥ Titel (Vorderseite) ¥ OSW 03/01
Bedienungsanleitung
Operating Instructions
Instructions dÕemploi
Instrucciones de servicio

Istruzioni dÕuso
Gebruiksaanwijzing
Betjeningsvejledning
Bruksanvisning
Brukerveiledningen
KŠyttšohje
OäèçÝá øåéòéóíïà
Kullanõm kõlavuzu
Deutsch
English

Espa–ol

Italiano
Nederlands
Dansk
Svenska
Norsk
Suomi
EììèîéëÀ

GBH 5-40 DE
GBH 5-40 DE (535) - Vorderseite  Seite 1  Montag, 26. MŠrz 2001  1:06 13 

 
1 619 929 535 ¥ 03.01
A
B
Ê2
60¡
50¡5¡
30¡           15¡ 15¡60¡
90¡
30¡
15
53¡ 2,5 r5,0 r
45¡
4
60¡
ca.60ca.40
60¡60¡
20¡
C 

 
1 619 929 535 ¥ 03.01
Ê1
Ê2Ê3Ê4Ê5
Ê6
Ê7
Ê9
Ê8 

English - 11 619 929 535 ¥ TMS ¥ 22.03.01
Measured values determined according to
EN 50 144.
Typically the A-weighted noise levels of the prod-
uct are: sound pressure level: 90 dB (A); sound
power level: 103 dB (A).
Wear ear protection!
84 / 537 / EEC: Noise level is lower than
108 dB (A).
The typical weighted acceleration is 6.8 m / s
2.
Ê1Dust protection cap
Ê2Locking sleeve
Ê3Mode selector switch
Ê4Vibration damper
Ê5On / Off switch
Ê6Speed selector thumbwheel
Ê7Service indicator...

English - 21 619 929 535 ¥ TMS ¥ 22.03.01
The machine is designed for drilling in concrete,
brick and stone as well as for chiselling.
nBefore any work on the machine itself, pull
the mains plug.
With the SDS-max tool holder, simpler and easier
tool changing is possible without additional aids.
+Grease the shank end of the tool regu-
larly.
The dust protection capÊ1 largely prevents the
entry of drilling dust during operation. When in-
serting the tool, take care that the dust protection
capÊ1 is not...

English - 31 619 929 535 ¥ TMS ¥ 22.03.01
Switching On / Off in chiselling mode:
Switching on:Press the upper part of the 
On / Off switchÊ5 until it locks 
onÊ(I).
Switching off:Press the bottom partÊ(0) of the 
On / Off switchÊ5 and release.
+At low temperatures it is possible that the
machine only reaches its full hammering or
impact rate after a certain period of time.
The electronic control enables continuous pre-se-
lection of speed and impact rate in accordance
with the material to be worked....

English - 41 619 929 535 ¥ TMS ¥ 22.03.01
The chisel can be locked in 12 positions. In this
manner, the optimum working position can be set
for each application.
Insert the chisel in the tool holder.
Turn the mode selector switchÊ3 to ÒChanging
the chiselling positionÓ (Vario-lock).
Turn the tool holder to the desired chiselling posi-
tion.
Allow the mode selector switchÊ3 to latch in the
ÒChisellingÓ position. The tool holder is locked in
this position.
The mode selector switchÊ3 must always be
locked...

English - 51 619 929 535 ¥ TMS ¥ 22.03.01
We guarantee Bosch appliances in accordance
with statutory / country-specific regulations (proof
of purchase by invoice or delivery note).
Damage attributable to normal wear and tear,
overload or improper handling will be excluded
from the guarantee.
In case of complaint please send the machine,
undismantled, to your dealer or the Bosch Serv-
ice Centre for electric power tools.
Recycle raw materials instead of disposing as
waste.
The machine, accessories and...

1 619 929 535 ¥ 03.01
L
ø
16 200  1 618 596 422
16 400  1 618 596 423
18 200  1 618 596 424
18 400  1 618 596 425
20 200  1 618 596 426
20 400  1 618 596 427
20 800  1 618 596 428
22 200  1 618 596 429
22 400  1 618 596 430
22 800  1 618 596 431
24 200  1 618 596 432
24 400  1 618 596 433
25 200  1 618 596 434
25 400  1 618 596 435
25 800  1 618 596 436¯L
(mm) (mm)28 250  1 618 596 437
28 450  1 618 596 438
28 550  1 618 596 439
30 250  1 618 596 440
30 450  1 618 596 441
32 250 1 618 596 442
32 450 1...

1 619 929 535 ¥ 03.01
L1
SDS
plus
2 608 550 036
1 608 571 055
1 618 598 157
M 14 2 613 349 027
M 16 2 613 349 028
M 20 1 613 349 010
M 22 1 613 349 011
M 24 1 613 349 012
M 27 1 613 349 013
M 30 1 613 349 0141 618 598 159
1 618 598 161
L2
L1
45 450 1 618 596 455
45 850 1 618 596 456
55 450 1 618 596 457
55 850 1 618 596 458
¯L1L2
(mm) (mm) (mm)
max
SDS
45 160 290 F 00Y 145 188
45 420 550 F 00Y 145 189
50 160 290 F 00Y 145 190
50 420 550 F 00Y 145 191
55 160 290 F 00Y 145 192
55 420 550 F 00Y 145 193
68...