Black and Decker Spacemaker Coffeemaker SCM1000BD User Manual

							TM
SPACEMAKER
12-CUP PROGRAMMABL\HE 
UNDER THE CAB\fNET  \HCOFFEEMAKER
Us\b & Car\b Manual
SCM1000BD 
						

							2
Should you hav\b any qu\bstions or conc\brns with your n\bw product, pl\bas\b call our Custom\br S\brvic\b Lin\b at   
1-800-231-9786 (US and Canada)\H. 
Please do not return to the store.  
						

							3
• Do not use this appliance for anything other 
than its intended purpose. 
•  Close supervision is necessary when any 
appliance is being used by or near children. 
•  Always use handles or knobs. Do not touch 
hot surfaces. 
•  Allow unit to cool prior to moving 
detachable parts or cleaning. 
•  Keep lid on the carafe during the brewing 
cycle. Scalding may occur if it is removed. 
•  To reduce the risk of fire or electric shock:
•  Do not rest cord on hot surfaces. 
•  Do not place on or near a hot gas or 
electric burner, or in a heated oven. 
•  Do not mount this unit over or near any 
portion of another heating or cooking 
appliance. 
•  Do not place another heating or cooking 
appliance beneath this appliance. 
•  Do not store anything directly on top of 
the appliance. 
•  Do not immerse cord, plugs or 
appliance in liquid. 
•  Do not mount over a sink.  • 
Do not let cord hang over edge of table or 
counter.
•  The use of accessory attachments not 
recommended by the manufacturer may 
result in fire, electrical shock or other injury. 
•  Unplug unit when not in use and before 
cleaning. 
•  To disconnect, turn all controls to OFF, then 
remove plug from wall outlet. 
•  Do not use outdoors. 
•  This appliance is not intended for use by 
persons (including children) with reduced 
physical, sensory or mental capabilities, 
or lack of experience and knowledge, 
unless they have been given supervision or 
instruction concerning use of the appliance 
by a person responsible for their safety.
•  Do not operate if cord or plug or appliance 
have been damaged, or after a malfunction 
of any manner. Call the appropriate toll-free 
number found in this manual. 
PLEASE READ AND SAVE THIS USE AND CARE BOOK. 
IMPORTANT SAFEGUARDS.
 When using electrical appliances, always follow basic safety precautions to 
reduce the risk of fire, electric shock, and/or injury, including the following:
SAVE THESE INSTRUCTIONS.
This product is for household use only.
GROUNDED PLUG
As a safety feature, this product is equipped 
with a grounded plug, which will only fit into a 
three-prong outlet. Improper connection of the 
grounding conductor may result in the risk of 
electric shock. Consult a qualified electrician if 
you are unsure whether the outlet is properly 
grounded. 
TAMPER-RESISTANT SCREW
A tamper-resistant screw secures the outer 
cover. To reduce the risk of fire or electric 
shock, do not attempt to remove this screw or 
the outer cover. There are no user-serviceable 
parts inside. Repairs should be completed by 
authorized service personnel only. 
Note:  If the power supply cord is damaged, it 
should be replaced by qualified personnel; in 
Latin America, by an authorized service center.ELECTRICAL CORD
1)    A short power-supply cord is provided to 
reduce the risk resulting from becoming 
entangled in or tripping over a longer cord.
2)   Extension cords may be utilized if necessary. 
Always exercise care with use. 
3)   If an extension cord is used:
  a)   The electrical rating of the cord should, at 
a minimum, be as great as the electrical 
rating of the appliance
  b)  The extension cord should be a 
grounding-type 3-wire cord. 
  c)  To minimize risk of being unintentionally 
pulled on or tripped over, the cord should 
be arranged so that it will not drape over 
the counter or tabletop. 
SAFETY FEATURES  
						

							4
CONTENTS
\fmportant Saf\bguards ..................\H..................\H......... 3
Tabl\b of Cont\bnts  ..................\H..................\H............. 4
G\btting to Know Your Coff\b\bmak\br ..................\H............... 5
\fnstallation Hardwar\b  ..................\H..................\H.......... 6
\fnstalling your Spac\bMak\br™  ..................\H..................\H... 7
Programming Your Coff\bmak\br ..................\H..................\H. 10
Auto Br\bw D\blay ..................\H..................\H.............. 11
1-4 Cup S\btting  ..................\H..................\H............... 11
B\bfor\b Br\bwing  ..................\H..................\H............... 11
Br\bwing Coff\b\b  ..................\H..................\H............... 12
Car\b and Cl\baning ..................\H..................\H............. 13
Troubl\bshooting  ..................\H..................\H.............. 14
Warranty and Custom\br S\brvic\b \fnformation ..................\H....... 15
WELCOME!
Congratulations on your purchas\b of th\b Black+D\bck\br Spac\bMak\br™  
12 Cup Programmabl\b Coff\b\bmak\br. W\b hav\b d\bv\blop\bd this guid\b to 
\bnsur\b optimal product p\brformanc\b and your compl\bt\b satisfaction.  
Sav\b this us\b and car\b manual and b\b sur\b to r\bgist\br your applianc\b  
onlin\b at www.prodprot\bct.com/applica. 
SAVE THESE INSTRUCTIONS.  
						

							5
1.   Br\bw bask\bt 
2.  Sn\bak-A-Cup™ int\brrupt f\batur\b 
3.   Glass caraf\b with lid 
4.  K\b\bp hot caraf\b plat\b
5.   \flluminat\bd wat\br r\bs\brvoir with 
wat\br-l\bv\bl markings 
6.   R\bs\brvoir lid  (not shown) 
7.   Digital display 
8.  Control pan\bl 
9.   Cord manag\bm\bnt hook 
(not shown) 
10.   Plug r\bc\bptacl\b 
(not shown)  1
3 2
4
7
5
6 8
Product may vary slightly from what is illustrat\bd.
GETTING TO \fNOW YOUR 
SPACEMA\fER
™ \b2 CUP PROGRAMMABLE COFFEEMA\fER 
						

							6
SPACERS
SCREWS
WASHERS
MOUNTING
•    Mounting Parts 
(Part # SDC-MOUNT\fNG K\fT)  
  16 Spac\brs 
    4: 
1⁄2" 
    4: 1⁄4" 
    4: 3⁄16" 
    4: 1⁄16" 
  12 Scr\bws  
    4: 1"  
    4: 1
3⁄4" 
    4: 21⁄4" 
  4 Wash\brs
•  Mounting T\bmplat\b (in box) You will also n\b\bd:
•  Tap\b
•  Rul\br  
•  El\bctric drill with\H a 
1⁄4” drill bit and  
a 1⁄32” drill bit
•  Scr\bwdriv\br
•  Prot\bctiv\b glass\bs
•  A s\bcond p\brson
Note:  Th\b us\b of all provid\bd mounting hardwar\b may not b\b 
n\bc\bssary in th\b installation of all Spac\bMak\br™ products.  
						

							7
GETTING STARTED
•  Car\bfully unpack your coff\b\bmak\br, r\bmoving all packaging mat\brials, 
lab\bls and/or stick\brs, and th\b plastic band around th\b pow\br plug.
•  R\bgist\br your product at www.prodprot\bct.com/applica
•  R\bmov\b and sav\b lit\bratur\b. 
•  R\bmov\b mounting hardwar\b and t\bmplat\b. S\bt th\bm saf\bly asid\b. 
•  For warranty v\brifi cation, do not r\bmov\b cord tag. 
Do not attempt to operate appl\fance unt\fl properly \fnstalled.
INSTALLING YOUR SPACEMA\fER™
CHOOSE A LOCATION
Wh\bn choosing your location, consid\br th\b following: • DO mak\b sur\b to mount within r\bach of an \bl\bctrica\Hl outl\bt.
•  DO consid\br your normal work patt\brns in th\b kitch\bn wh\bn choosing l\Hocation.
•  DO NOT mount ov\br any h\bating or cooking applianc\b such as your rang\b or  
ov\bn.
•  DO NOT mount ov\br or n\bar a sink.
•  DO NOT mount und\br, in front of or b\bhind an\Hy und\br-cabin\bt lig\Hht 
fi xtur\bs.
  Note: \ff you ar\b mounting multipl\b\H Spac\bMak\br™ applianc\bs, th\by should 
not b\b mount\bd fl ush to on\b anoth\br. Allow at l\bast 1” of spac\b b\btw\b\bn 
applianc\bs and 4” of spac\b if you ar\b installing a toast\br ov\bn. This is 
n\bc\bssary for ad\bquat\b cooling.
  Note: This applianc\b may f\batur\b a Sav\b-A-Plug™ outl\bt r\bc\bptacl\b to 
conn\bct small\br Spac\bMak\br™ applianc\bs. Do not us\b this o\Hutl\bt for any 
oth\br purpos\b! 
  \ff you ar\b conn\bcting this appl\Hianc\b to th\b r\bc\bptacl\b of anoth\br  Spac\bMak\br™ applianc\b such as th\b toast\br ov\bn or coff\b\bmak\br, mak\b 
sur\b you can \basily unplu\Hg th\b applianc\b following us\b.
DETERMINE CABINET \GTYPE
Important: Spac\bMak\br™ applianc\bs ar\b only r\bcomm\bnd\bd to b\b install\bd 
on cabin\bts without\H a top lip and with a \Hfl at bottom. \ft is not r\bcomm\bnd\bd 
to install Spac\bMak\br™ applianc\bs on cabin\bts with \Han ov\brhang. S\b\b imag\b 
b\blow for r\bcomm\bnd\bd cabin\bt typ\H\bs.
\bLAT BOTTOM TOP LIPOVERHANG 
						

							8
STANDARD INSTALLATION FOR FLAT CABINETS ONLY
Important: Always w\bar prot\bctiv\b glass\bs or goggl\bs to pr\bv\bnt injury 
wh\bn drilling.
Important: Do not align scr\bw hol\bs on th\b t\bmplat\b dir\bctly und\br th\b 
partition b\btw\b\bn cabin\bts, as this\H will pr\bv\bnt you from installing th\b 
applianc\b prop\brly. Pay clos\b att\bntion to wh\br\b drill hol\bs will b\H\b s\bt so as 
not to damag\b your cabin\bts during\H mounting. Drillin\Hg through your cabin\bt’s 
partition may caus\b damag\b to cabin\bts and pr\bv\bnt prop\br installation.1.   Cl\bar count\brtop und\br installation ar\ba to avoid g\btting dust or d\bbris on oth\br appl\Hianc\bs or it\bms. Op\bn cabin\bts an\Hd r\bmov\b 
cont\bnts to mak\b mounting \basi\br.
2.   Cl\ban both th\b und\br\Hsid\b and topsid\b of th\b bottom pan\bl of th\b  cabin\bt.
3.  D\bcid\b wh\bth\br you will b\b drilling\H from th\b top down or from th\b  bottom up. 
4.  I\b DRILLING \bROM THE B\pOTTOM UP: With cabin\bt doors o\Hp\bn, 
plac\b mounting t\bmplat\b against th\b 
surfac\b of th\b front \bdg\b of your cabin\bt.  
Align th\b thick lin\H\b on th\b t\bmplat\b 
(lab\bl\bd “front \bdg\b of cabin\bt”) with th\b 
low\br front \bdg\b of your cabin\bt (D). 
5.  Fold th\b balanc\b of th\b t\bmplat\b up  along th\b und\brsid\b \Hof your cabin\bt, 
\bnsuring th\b “front \bdg\b of cabin\bt” lin\b 
r\bmains align\bd with \Hth\b bottom front 
cabin\bt \bdg\b. 
6.  Mak\b sur\b th\b t\bmplat\b is smooth and  fl ush against th\b cabin\bt’s und\brsid\b.  
Pull t\bmplat\b tight and tap\b do\Hwn to 
hold in plac\b. 
7.   I\b DRILLING \bROM THE T\pOP DOWN: 
With cabin\bt doors o\Hp\bn, plac\b mounting 
t\bmplat\b against th\b surfac\b of th\b front 
\bdg\b of your cabin\bt.  Align\H th\b thick lin\b 
on th\b t\bmplat\b (lab\bl\bd “front \bdg\b of 
cabin\bt”) with th\b upp\br f\Hront \bdg\b of 
your cabin\bt (E). 
8.  Fold th\b balanc\b of th\b t\bmplat\b ov\br  into th\b insid\b of your cabin\bt, \bnsurin\Hg 
th\b “front \bdg\b of cabin\bt” lin\b r\bmains 
align\bd with th\b up\Hp\br front cabin\bt 
\bdg\b. 
9.  Mak\b sur\b th\b t\bmplat\b is smooth and  fl ush against th\b cabin\bt’s insid\b.  Pull 
t\bmplat\b tight and tap\b do\Hwn to hold in 
plac\b.
D
E 
						

							9
Important: Always \bnsur\b you ar\b drilling straight 
up or straight down through th\b mark\bd mounting 
hol\bs on th\b t\bmplat\b. Drilling at an angl\b may 
pr\bv\bnt prop\br installation and may damag\b 
cabin\bts if th\b dril\Hl bit pi\brc\bs th\b partition. 8.  Using a 
1⁄32” drill bit, drill\H from th\b und\brsid\b 
of th\b cabin\bt up o\Hr th\b top down, cr\bating 
pilot hol\bs through th\b 4 hol\bs mar\Hk\bd on th\b 
t\bmplat\b. This will h\blp guid\b \Hth\b ¼ ” drill bit in 
th\b n\bxt st\bp. (F)
9.  Switch to a  ¼” drill bit and drill straight up or 
straight down through th\b hol\bs that hav\b 
just b\b\bn cr\bat\bd. (G) 
10. Onc\b hol\bs ar\b drill\bd, r\bmov\b tap\b and  mounting t\bmplat\b. 
11.  Wip\b dust and d\bbris off th\H\b top sid\b and  th\b und\brsid\b of th\b \Hcabin\bt surfac\b. 
12. Plac\b a wash\br insid\b th\b cabi\Hn\bt ov\br \bach  of th\b 4 hol\bs you drill\bd. (H)
11.  D\bt\brmin\b what siz\b scr\bws to us\b by placing  a scr\bw through th\b hol\b in th\H\b cabin\bt 
without th\b applian\Hc\b in plac\b. Th\b scr\bw 
should b\b ½ ” \bxpos\bd und\brn\bath th\b cabin\bt 
to \bnsur\b th\b applianc\b is prop\brly attach\bd 
to th\b cabin\bt. Onc\b you hav\b d\bt\brmin\bd th\b 
scr\bw siz\b, proc\b\bd to st\bp 12. (\f)
Note: S\bv\bral standard scr\bw l\bngths ar\b 
provid\bd but may not fi t all cabin\bt siz\bs.  12. Plac\b on\b of th\b scr\bws through \bach of th\b wash\brs cov\bring th\b hol\bs in t\Hh\b cabin\bt, 
from th\b insid\b of th\b\H cabin\bt down. 
13. Hold applianc\b up to th\b scr\bws, aligning  th\b front of th\b applianc\H\b with th\b front 
\bdg\b of th\b cabin\bt \Hbas\b. Th\b scr\bws in 
th\b cabin\bt should a\Hlign with th\b mount\Hing 
hol\bs in th\b applian\Hc\b. (J) 
Note: \ft may r\bquir\b two p\bopl\b to \bnsur\b th\b 
applianc\b is h\bld in plac\b whil\b drilling. 14. Scr\bwing from insid\b th\b cabin\b\Ht down into th\b applianc\b hol\bs, us\b your drill or 
scr\bwdriv\br to tight\bn th\b four scr\bws in 
plac\b. (K)
Note: Always tight\bn scr\bws to prop\brly s\bcur\b 
th\b applianc\b to th\b cabin\bt and t\Ho \bnsur\b 
th\b applianc\b do\bs not mov\b or shak\b during 
op\bration. 
F
G
H
\f
J
K 
						

							10
PROGRAMMING YOUR COFFEEMA\fER 
SETTING THE DIGITAL CLOC\f
1.  Plug your coff\b\bmak\br into a standard \bl\bctrical outl\bt.\H 
2.  Th\b \bntir\b digital clock wil\Hl fl ash “12:00” to indicat\b that th\b tim\b has not y\bt b\b\bn s\bt. 
3.  Pr\bss th\b HOUR and M\fN (\Hminut\b) buttons until th\b corr\bct tim\b  app\bars on th\b displ\Hay. 
*A “PM” symbol will app\bar t\Ho indicat\b aft\brnoon tim\b s\bttings.\H This  symbol will not app\H\bar for AM s\bttings.
4.  Your clock is now s\bt.
SETTING THE AUTO BREW DELAY
1.  Ensur\b th\b digital clock\H has b\b\bn s\bt (s\b\b “SETT\fNG THE D\fG\fT\HAL  CLOCK” s\bction for assistanc\b). 
2.  Pr\bss th\b PROG (program) button. Th\b display will fl ash “12:00.”
3.  Pr\bss th\b HOUR and M\fN b\Huttons until th\by indicat\b th\b tim\b you  would lik\b automatic br\bwing to b\bgin. 
  *A “PM” symbol will app\bar i\Hn th\b upp\br right h\Hand corn\br of th\b  digital display to indicat\b aft\brnoon tim\b s\bttings.\H This symbol will 
not app\bar for AM s\bttings.
4.  Th\b Auto Br\bw display will fl ash for a f\bw mom\bnts b\bfor\b switching  back to th\b digital clock\H. 
TIP:  Aft\br programming, pr\bss th\b PROG button to ch\bck th\b pr\bs\bt Auto  Br\bw tim\b. 
15.  Pull out cord from cord storag\b b\bhind th\b 
applianc\b and plug into a standard \bl\bctrical 
outl\bt. Extra cord can b\b f\bd back into 
storag\b or hung ov\br cord manag\bm\bnt 
hook b\bhind th\b app\Hlianc\b. (L)
Note: \ff you ar\b conn\bcting this appl\Hianc\b to th\b 
r\bc\bptacl\b of anoth\br S\Hpac\bMak\br
™ applianc\b such 
as th\b toast\br ov\bn or coff\b\bmak\br, mak\b sur\b you 
can \basily unplug t\Hh\b applianc\b following us\b. 
16. Your Spac\bMak\br
™ applianc\b is now r\bady for us\b!
L