Bissell 7920-j Manual

11
Carpet Cleaning
1.
2.
3.
4.
5.
 ATTENTION 
BERBER CARPET 
OWNERS:
Some Berber Carpets have a 
tendency to fuzz with wear. 
Repeated strokes in the 
same area with an ordinary 
vacuum or deep cleaner may 
aggravate this condition. 
Please see Stain Removal 
instructions on page 12.
Plug into a proper outlet and turn the Power Switch 
ON. Wait two minutes for the heater to warm up before 
beginning to clean.
While pressing the trigger, make one slow forward wet 
pass and another one back. Let the...

12
Stain Removal
Do Not Delay! Failure to attend to an accident soon after it occurs 
may cause it to set and become permanent.
Before treating any stain, follow these pretreatment steps:
Blot up liquids with an absorbent cloth or paper towels. 
White materials are recommended because certain dyes 
may bleed and make the stain worse.
Gently scrape up semi-solids with a spoon or spatula. 
Do not use a knife or other utensil with sharp edges 
because it could damage the carpet or upholstery.
If the area...

13
Stain Removal In Between Deep Cleaning
Do Not Delay! Failure to attend to an accident soon after it occurs
may cause it to set and become permanent.
Use OxyKIC
™ carpet spot & stain remover to permanently remove 
tough spots and stains like red wine, cola and fruit juice in 
between deep cleaning.
OxyKIC has a revolutionary Dual Chamber System that activates 
the power of oxygen with a tough spot cleaner. The result is a 
powerful, oxygen activated spray that makes spot & stain removal 
easy – no...

14
 The Perfect Pass feature is designed to help you achieve the best 
cleaning results when deep cleaning. 
Apply smooth even strokes when deep cleaning your carpets. An 
upright deep cleaner should not be used at the same speed as an 
ordinary vacuum. That is too fast for optimum cleaning results.
The Perfect Pass indicator displays a red light which tells you if 
you are in the range of Best Cleaning or if you are going To o  
Fast. If you notice consistently that the indicator light is in the To o...

15
Check manufacturer’s tag before cleaning. “W” or “WS” on 
the tag means you can use your ProHeat Pro-Tech. If the 
tag is coded with “X” or “S” (with a diagonal strike through), 
or says “Dry Clean Only,” do not proceed. The Scotchgard
™ 
protector is not recommended for use on velvet, silk, 100% 
cotton upholstery, vinyl or leather. If manufacturer’s tag is 
missing or not coded, check with your furniture dealer.
Check for colourfastness in an inconspicuous place.
 If possible, check upholstery...

16
The Bare Floor Tool provides effective cleaning for linoleum, vinyl, 
and tile floors. 
Caution: Do not use on hardwood floors. 
Use BISSELL Hard Floor Solutions in SmartMix Bottle.
Vacuum or sweep thoroughly to pick up loose debris and pet hair.
Remove easily moved furniture from the room (chairs, tables, etc).
Plan your cleaning route to leave an exit path.
Plan activities to allow 30 minutes for the floor to dry completely.
Step on the Handle Release to lay the machine handle down.
Remove the...

Machine Preparation
1.
2.
3.
4.
17
Set up machine following instructions in the Features section 
on pages 6-9. Be sure to thoroughly rinse out any remaining 
BISSELL Advanced Deep Cleaning Formula from the SmartMix 
Bottle to prevent slippery linoleum, vinyl, and tile floors. Use 
BISSELL Hard Floor Solutions in the SmartMix Bottle.
Check ReadyTools Dial - it should be set on Floor Cleaning.
Choose the SmartMix setting to match the cleaning job.
Plug into a proper outlet and turn Power Switch ON. The...

18
Routine Maintenance
Turn Power Switch OFF.
Unplug power cord from the outlet and coil around Power Cord 
Quick Release.
Remove and rinse tools in clean, running water. Dry and 
replace on tool caddy.
Coil Flex Hose around storage brackets on Tool Caddy.
Remove Tank-In-Tank, dispose of dirty water. Refer to the 
Features section on Pages 8-9.
Rinse out Tank-In-Tank and replace on the machine; Clean out 
Lint Screen.
Clean out the Flow Indicator Filter each time it is used to ensure 
best cleaning...

19
Turn the Power Switch OFF and unplug from the wall outlet.
Step on the Handle Release and recline the handle down onto 
floor (see illustration).
Remove Tank-In-Tank and SmartMix Bottle. Set them aside 
(see illustration).
Remove Belt Access Door located near the Floor Cleaning/
Tools switch by inserting a flat head screwdriver into the slot 
nearest to the handle and gently prying the access door off 
(see illustration).
Turn the machine onto its side so the belt access area is 
facing upward (see...

20
To Install the Replacement Pump Belt
With the unit still on its side, loop one end of the Replacement 
Pump Belt around the red pump pulley and then the other end 
around the silver motor shaft (see illustration). Do not twist the 
Replacement Pump Belt.
Re-install the “toothed” Brush Belt first onto the red pump pulley 
and then onto the “toothed” end of the brush (see illustration).
Re-install the brush into the base of unit.
Place the black brush arm onto the brush and slide black 
brush arm into...