Bissell 1699 N Manual

11
Disconnect the TurboBrush from the flex hose by pushing
down on the button lock and pulling straight off.
Once removed from the Flex Hose, the TurboBrush can 
be cleaned.
AMove the switch to the “SUCTION” position.
BRinse under running water.
CCheck spray nozzle for dirt. If necessary, clean with a soft
bristle brush.
DReplace TurboBrush in the special storage location on the
handle front. (on select models only)
Plan activities to give carpet time to dry.
Remove easily moved furniture from the room...

12
Pretreating is recommended to improve cleaning 
effectiveness for heavily soiled carpet in high traffic 
areas such as entryways and hallways:
Set the SmartMix dial to High Traffic.
Set ReadyTools dial to PreTreat.
Plug into a proper outlet and turn on both the Power and
Smart Temp Switches.
While pressing the trigger slowly make several passes over
the area to be cleaned.Caution Do not overwet.
Turn the machine Power Switch OFF and let the BISSELL
Advanced Cleaning Formula dissolve the tough soil for...

13
Stain Removal
Do Not Delay! Failure to attend to an accident soon after it occurs
may cause it to set and become permanent.
Before treating any stain, follow these pre-treatment steps:
Blot up liquids with an absorbent cloth or paper towels.
White materials are recommended because certain dyes
may bleed and make the stain worse.
Gently scrape up semi-solids with a spoon or spatula. Do
not use a knife or other utensil with sharp edges
because it could damage the carpet or upholstery.
If the area has...

14
1.
Check manufacturer’s tag before cleaning. “W” or “WS”
on the tag means you can use your ProHeat ClearView.
If the tag is coded with “X” or “S” (with a diagonal strike
through), or says “Dry Clean Only,” do not proceed. Do
not use on velvet or silk. If manufacturer’s tag is missing
or not coded, check with your furniture dealer.
Check for colorfastness in an inconspicuous place.
If possible, check upholstery stuffing. Colored stuffing
may bleed through fabric when wet.
Plan activities to give...

15
Set up the machine following instructions in the Features
section, pages 6-11.
Use BISSELL Advanced Cleaning Formulas in SmartMix tank.
Set the ReadyTools dial to Tools or PreTreat.
* SmartTemp heats the cleaning solution for carpet 
and bare floor application only. It does not heat 
solution sprayed through the accessory tools.
Set SmartMix Dial to Normal.
Choose the 4” Small Area Tool, the Tough Stain Brush, or the
Spraying Crevice Tool and connect to the Flex Hose.
Plug into a proper outlet and...

16
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
6.
Cleaning Bare Floors
The Bare Floor Tool is included in select models only.
If your ProHeat CleaView did not come so equipped,
you may contact BISSELL Consumer Services at
www.bissell.com or 1-800-237-761 to order one. The
Bare Floor Tool provides effective cleaning for linoleum,
vinyl, and tile floors.
Caution: Do not use on hardwood floors.
Use BISSELL Floor Cleansing Formula.
Vacuum or sweep thoroughly to pick up loose debris and pet hair.
Remove easily moved...

17
Machine Preparation
Set up machine following instructions in the Features
section, pages 6-11. Be sure to thoroughly rinse out any
remaining Fiber Cleansing Formula from the SmartMix 
bottle to prevent slippery linoleum, vinyl, and tile floors.
Use BISSELL Floor Cleansing Formula in 
the SmartMix tank.
Check ReadyTools Dial - it should be set on Floor Cleaning.
Choose the SmartMix setting to match the cleaning job.
Plug into a proper outlet and turn Power Switch ON. Turn
SmartTemp switch ON. The...

18
Routine Maintenance
Turn Power and SmartTemp switches OFF.
Unplug power cord from the outlet and coil around Power
Cord Quick Release.
Remove and rinse tools in clean, running water, dry and
replace in the Tool Caddy.
Coil Flex Hose around storage brackets on Tool Caddy.
Remove Tank-In-Tank, dispose of dirty water. See Features
section, page 8-9.
Rinse out Tank-In-Tank and replace on the machine; Clean
out lint trap.
Clean out the Flow Indicator Filter each time it is used to
ensure best cleaning...

Turn the machine off and unplug from the wall outlet.
Step on the release pedal and recline the handle down onto
floor (see illustration).
Remove Tank-In-Tank and SmartMix tanks. Set them aside
(see illustration).
Remove Belt Access Door located near the Floor Cleaning/
Tools switch by inserting a flat head screwdriver into the
slot nearest to the handle and gently prying the access door
off (see illustration).
Turn the machine onto its side so the belt access area is 
facing upward (see illustration)....

20
With the unit still on its side, loop one end of the replacement
pump belt around the red pump pulley and then the other end
around the silver motor shaft (see illustration). Do not twist the
replacement pump belt.
Re-install the toothed brush belt first onto the red pump pulley
and then onto the toothed end of the brush (see illustration).
Re-install the brush into the base of unit.
Place the black brush arm onto the brush and slide black
brush arm into base of unit. The black brush arm and brush...