Bisell PROheat AllRounder 7700 User Manual
Have a look at the manual Bisell PROheat AllRounder 7700 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 201 Bissell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
11www.bissell.com Operation Carpet Cleaning (continued) 7. Continue to clean entire carpet working in one meter by one meter sections. 8. If machine loses suction, stop spraying and check the collection tank level. Empty if necessary. 9. If the machine stops spraying turn off wet clean button immediately and check the solution tank level. NOTE: Never run in wet clean mode when the clean water formula tank is dry or missing. When you are finished 1. Turn off the heater, wet clean, and power buttons. 2. Remove the collection tank from the unit by opening the quick release hose holder and lifting the tank straight up by the handle. 3. Remove the top lid from the collection tank and set it aside. 4. Empty dirty water into a sink, toilet or outside. Pour the dirty water out from the corner of the tank. Rinse out the tank thoroughly. NOTE: You may leave the solution tank with water and formula in it so you are ready for the next use. 6. Allow all parts to dry before storing. Hard floor cleaning 1. See “Getting Ready to Wet Clean” on Page 10. 2. Be sure to use BISSELL Hard Floor Solutions in the solution tank for hard floor cleaning. Fill the formula tank by first unscrewing the measuring cap. Always use genuine BISSELL formulas to maximize cleaning and for the safety of your machine. Fill tank to fill line with hot tap water. Add one full cap of formula. Screw measuring cap tightly back onto the solution tank. 3. Set the solution tank back in the machine. 23 2 ug120-4005_7700_607.indd 11ug120-4005_7700_607.indd 116/28/07 10:05:56 AM6/28/07 10:05:56 AM
12www.bissell.com Operation Hard floor cleaning (continued) 4. Attach microfibre pad to quick dry hard floor tool by attaching to the Velcro strips on the top of the tool. 5. Attach the quick dry hard floor tool to end of the wand. 6. Place tool directly on the hard floor surface, resting on the pad. 7. Squeeze the spray trigger to moisten the pad with cleaning solution. Caution: Do not oversaturate. 8. Move the tool back and forth across the floor to clean. Squeeze spray trigger as needed. 9. Tilt the tool forward and pull back. This will create the best suction and will help get the hard floor surface as dry as possible. 10. Continue until room is complete. 11. See “When You Are Finished” instructions on page 11. 12. Be sure to remove the microfibre pad and clean it by hand or machine wash as needed. Allow it to dry completely before next use. Upholstery cleaning Your PROheat All-Rounder comes with special tools for vacuuming and wet cleaning upholstery, stairs and more. 1. Important! If using to wet clean upholstery, check the upholstery tags proceeding. a. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your PROheat All-Rounder. If the tag is coded with an “X” or an “S” (with a diagonal stripe through it), or says “Dry Clean Only”, do not proceed with deep cleaning. Do not use on velvet or silk. If manufacturer’s tag is missing or not coded, check with the furniture maker or the furniture dealer. b. Check for colourfastness in an inconspicuous place. c. If possible, check upholstery stuffing. Coloured stuffing may bleed through fabric when wet. d. Plan activities to allow upholstery time to dry. e. Vacuum thoroughly. 2 Adsdfdd ghg bvh cvbbj jkn hnbj jkvh gcghhjj jhffhl kllgh Manufacturer’s tag ug120-4005_7700_607.indd 12ug120-4005_7700_607.indd 126/28/07 10:05:59 AM6/28/07 10:05:59 AM
13www.bissell.com Operation Upholstery cleaning (continued) 2. Refer to the “Getting Ready to Wet Clean” on page 10. 3. Attach the desired wet cleaning tool to the wand or grip. 4. Clean by pressing the spray trigger to spray solution onto the area to be cleaned. Slowly move the tool back and forth over the soiled surface. Release the spray trigger to suction soiled water. Continue to clean the area, working in small sections, until no more dirt can be removed. Suction as needed to remove as much water as possible. Caution: Do not overwet. 5. Remove and rinse tools in clean, running water. Dry and put away. 6. See When you are finished instructions on page 11. Cleaning fluid section Keep plenty of genuine BISSELL Formula on hand so you can clean and protect whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas. 1.42 L Fiber Cleansing Formula ™ with Scotchgard™ protector item # 710E 1.42 L Multi-Allergen Removal ™ Formula with Scotchgard™ protector item # 720E 1.42 L Pet Odor and Soil Removal ™ Formula with Scotchgard™ protector item # 730E 1.42 L Natural Orange Extract Formula ™ with Scotchgard™ protector item # 740E 1.42 L Lavender Essence Formula ™ with Scotchgard™ protector item # 750E 1.42 L Lavender Essence Formula ™ with Scotchgard™ protector item # 750E Tip: It is recommended that you suction clean water from the tap to rinse out the hose. ug120-4005_7700_607.indd 13ug120-4005_7700_607.indd 136/28/07 10:06:00 AM6/28/07 10:06:00 AM
Maintenance and care Machine storage Once your cleaning is complete make sure the dirty water from the collection tank is emptied. Rinsed out and dry before the next use. For wet cleaning, the solu- tion tank can be left filled and ready to use. Note: Store your PROheat All-Rounder in a protected dry area. Since this product uses water it must not be stored where there is a danger of freezing. Freezing will damage the internal components and void the warranty. WARNING: To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL Deep Cleaning Formula intended for use with the deep cleaner. Non-BISSELL cleaning formula may harm the machine and void the warranty. 14www.bissell.com ug120-4005_7700_607.indd 14ug120-4005_7700_607.indd 146/28/07 10:06:09 AM6/28/07 10:06:09 AM
Maintenance and care Machine care For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete. 1. Press all buttons OFF. Unplug the machine and wrap the cord. 2. After emptying the dirty water from the collection tank, rinse it out thoroughly with hot water. Remove all inner parts (water filtration tower and mode selector) if desired. Rinse them and allow to dry before returning into tank. Note: To remove inner parts, turn mode selector to remove. Pull mode selector straight out towards you. The water filtration tower can now be taken out through the top of the tank. 3. For wet cleaning, remove and clean all tools that were used. Allow to dry before storing. 4. Remove the hose, taking care to keep both ends up to avoid spilling. Dump out any remaining water and flush clean with hot tap water. Allow to dry before storing. 5. a. Pre-motor filter: Take apart the top lid by pulling the tab away from the separator. Inspect the foam filter. If dirty, rinse clean and allow to dry before returning it to the machine. Re-assemble the top lid by plac- ing the filter in its spot and re-attaching the separator. Use care to make sure the “T” pieces are lined up under the shallow grooves on the top lid itself. For replace- ment of this part, see pages 18-19. b. HEPA Media filter: This filter is located at the back of the machine, underneath the Quick Release Cord Wrap. Use one finger to depress the latch and pull the door down. Open towards you and down to the ground. Use two hands to remove the filter from its slot. If dirty, rinse clean and allow to dry before returning it to the machine. Make sure the filter door is fully closed prior to operating the machine. For replacement of this filter see pages 18-19. www.bissell.com15 Water Filtration TowerMode Selector ug120-4005_7700_607.indd 15ug120-4005_7700_607.indd 156/28/07 10:06:09 AM6/28/07 10:06:09 AM
Troubleshooting
Reduce Spray or No Spray
Possible Cause Remedies
1. Make sure power is on 1. Press power button if needed
2. Solution tank may be empty 2. Fill tank according to directions
3. Tank may not be seated properly 3. Turn ON/OFF, heater and wet clean
button off. Remove and reseat tank
4. Hose solution line may be disconnected 4. Check connection at front of
machine
5. Wet clean is not turned on 5. Depress wet clean button to turn on
Machine is not suctioning
Possible Cause Remedies
1. Collection tank may not be placed properly 1. Open Quick Release™ Hose Door, lift
out tank and re-seat. Re-latch Quick
Release™ Hose Door
2. Collection tank may not be 2. Check to make sure the top lid is
assembled properly properly seated
3. Wand tool connections are not tight 3. Check all connections
(At grip, wand and tool)
Push tight if necessary.
4. Collection tank is full 4. Empty collection tank by following
instruction on page 9
5. Float has tripped 5. Check to see if tank needs to be
emptied. Make sure float is down
towards bottom of tank.
6. Pre-motor filter is dirty 6. Remove top lid. Remove and
clean pre-moter filter by following
instructions on page 15.
Filter must be completely dry
before using again
Built-in heater light does not illuminate
Possible Cause Remedies
1. The heater button has not been depressed 1. Depress the heater button
2. The ON/OFF button has not been depressed 2. Depress the ON/OFF button
Other maintenance or service not included in the manual should be performed by an
authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
WARNING: To reduce the risk of fire,
electric shock or injury
unplug from outlet before
servicing.
16www.bissell.com
ug120-4005_7700_607.indd 16ug120-4005_7700_607.indd 166/28/07 10:06:12 AM6/28/07 10:06:12 AM
www.bissell.com BISSELL Consumer Services If your BISSELL product should require service: In the UK, or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair. If you have questions about your warranty or need replacement parts please contact the numbers below. Or visit the BISSELL website - www.bissell.com When contacting BISSELL, have model number of unit available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________ Note: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim. See Warranty on page 20 for details. Please do not return this product to the store. 17 For UK inquiries: Monday - Thursday 9 am — 5 pm Friday 9 am — 4 pm BISSELL Homecare (Overseas) Inc. The Boat Yard 105 Straight Road Old Windsor Berkshire, SL4 2SE United Kingdom Telephone: 0870-225-0109 For all other inquiries: Monday - Friday 8 am — 4 pm BISSELL Homecare, Inc. PO Box 1888 Grand Rapids, MI 49501 USA Telephone: 01-616-453-4451 Fax: 01-616-453-1383For New Zealand inquiries: Monday - Friday 9 am — 5 pm Parex Industries Ltd. 103 Central Park Drive Henderson Auckland New Zealand Telephone: 0800-247-735 ug120-4005_7700_607.indd 17ug120-4005_7700_607.indd 176/28/07 10:06:13 AM6/28/07 10:06:13 AM
www.bissell.com Replacement parts - BISSELL PROheat All-Rounder Below a list of common replacement parts*. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired. Item Part No. Part Name 1 203-7063 Mulit-Surface Floor Tool 2 203-7064 Air Powered Floor TurboBrush 3 203-7073 5 Brush 4 203-7066 Wand 5 203-7067 Adaptor 6 203-7068 Crevice Tool 7 203-7069 Upholstery Dusting Brush 8 203-7070 Carpet Deep Cleaning Tool 9 203-7071 Carpet Deep Cleaning Tool Brush Strip 10 203-7072 Carpet Deep Cleaning Tool Adaptor 11 203-7065 4 Upholstery Tool 12 203-7074 Quick Dry Hard Floor Tool (pads not included) 13 203-7076 Hard Floor Microfibre Pads (2 Pack) 14 203-7077 Drain Cleaner 15 203-7078 Tool Caddy 16 203-7079 Hose Grip Assembly 17 203-7080 Measuring Cap 18 203-7082 Pre-Motor Filter 19 203-7083 HEPA Media Filter 20 203-7084 Solution Tank 21 203-7085 Small cap/insert 22 203-7086 HEPA Filter Door 23 203-7087 Float 24 203-7088 Diverter 25 203-7089 Water Filtration Tower 26 203-7090 Water Filtration Tower Gasket 27 203-7091 Separator with Filter 28 203-7092 Top Lid Assembly 29 203-7093 Lid 30 203-7096 Collection Tank 31 203-7097 Collection Tank Assembly 32 203-7098 Motor Duct Gasket 33 203-7099 Quick Release™ Hose Door™ Assembly 34 203-7100 Carry Handle Assembly 35 203-7102 Caster Wheel 36 710E 1.42 L Fiber Cleansing Formula ™ with Scotchgard™ protector 37 720E 1.42 L Multi-Allergen Removal™ Formula with Scotchgard™ protector 38 730E 1.42 L Pet Odor and Soil Removal™ Formula with Scotchgard™ protector 39 740E 1.42 L Natural Orange Extract Formula™ with Scotchgard™ Protector 40 750E 1.42 L Lavender Essence Formula™ with Scotchgard™ protector 41 0484 0.95 L Hard Floor Solutions™ *Not all parts are included with every model. 18 ug120-4005_7700_607.indd 18ug120-4005_7700_607.indd 186/28/07 10:06:13 AM6/28/07 10:06:13 AM
Replacement parts - BISSELL PROheat All-Rounder
1 2 3 4 5 6 7
8 91011121314
15161718192021
22232425262728
29303132333435
36 37 38 39 40 41
19www.bissell.com
(Pads not included
ug120-4005_7700_607.indd 19ug120-4005_7700_607.indd 196/28/07 10:06:13 AM6/28/07 10:06:13 AM
20www.bissell.com Warranty - BISSELL PROheat All-Rounder This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or contact your local in country distributor. Limited Two Year Warranty Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., will replace (with new or remanufactured components), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for two years any defective or malfunctioning part do to manufacturers defect. This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered. BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. *EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE. For UK inquiries: Monday - Thursday 9 am — 5 pm Friday 9 am — 4 pm BISSELL Homecare (Overseas) Inc. The Boat Yard 105 Straight Road Old Windsor Berkshire, SL4 2SE United Kingdom Telephone: 0870-225-0109 For all other inquiries: Monday - Friday 8 am — 4 pm BISSELL Homecare, Inc. PO Box 1888 Grand Rapids, MI 49501 USA Telephone: 01-616-453-4451 Fax: 01-616-453-1383For New Zealand inquiries: Monday - Friday 9 am — 5 pm Parex Industries Ltd. 103 Central Park Drive Henderson Auckland New Zealand Telephone: 0800-247-735 ©2007 BISSELL Homecare, Inc Grand Rapids, Michigan All rights reserved. Printed in China Part Number 120-4005 Rev 6/07 Visit our website at: www.bissell.com Scotchgard is a trademark of 3M ug120-4005_7700_607.indd 20ug120-4005_7700_607.indd 206/28/07 10:06:32 AM6/28/07 10:06:32 AM