Bisell PROheat 2x Healthy Home 20N4 User Manual

							16w w w . b i s s e l l . c o m 	11
Operation
Carpet c\beaning (continued)
2. Remove form\fl\b t\bnk  from back of machine.  
2\b.  fill the form\fl\b t\bnk  b\f first unscrewing the 
cap and insert. Alwa\fs use genuine BISSELL 
formulas to maximize cleaning and for the 
safet\f of \four machine. Fill water up to " WATER" 
line and then fill up to " Fo Rm ULA " line with 
BISSELL 2X concentrated formula. Replace the 
cap and insert. Place formula tank back into the 
slot in the back of the machine for a snug fit.
3.  Set c\fstom  cle\bn di\bl.  Simpl\f choose one  of 
the 4 settings (heav\f traffic, normal clean, 
light clean, or water rinse) and the ProHeat 
2X will adjust the right amount of cleaning 
formula to mix with the heated water to fit 
\four cleaning need.
4.  Set Re\bdy tools di\bl  to the floor cleaning setting.
5.  pl\fg into \b proper o\ftlet  and turn the power 
and heater switches to the  oN ( I ) position. 
Allow 1 minute for the built-in heater to warm-
up before cleaning. The ProHeat 2X will be full\f 
warmed and will provide optimal performance 
after one minute of continuous heated cleaning.
6.  cle\bning strokes.  While pressing the spra\f 
trigger,  make one slow forward wet pass and 
another one back. Let the built-in heater, formula, 
and DirtLifter PowerBrushes do the work for \fou. 
c \b\ftion: Do not overwet.  Take care not to run 
over loose objects or edges of area rugs. Stalling 
brush ma\f result in premature belt failure.  
Note:  yo\fr m\bchine is eq\fipped with \b   
circ\fit bre\bker th\bt will \b\ftom\btic\blly sh\ft 
off the br\fsh if \b l\brge or loose object is 
c\b\fght in the br\fsh roll. If th\bt h\bppens, be 
s\fre to \fnpl\fg yo\fr m\bchine, remove the 
foreign object, \bnd then pl\fg the m\bchine 
b\bck in to reset the circ\fit bre\bker.   
Release the spra\f trigger and make one 
slow forward and backward pass over   
the same area to remove an\f residual   
dirt\f water and aid in dr\fing. Repeat   
cleaning passes until solution being pulled 
up appears clean.  Continue passes without 
pressing the spra\f trigger until \fou can’t see 
an\f more water being pulled up. 
FLOOR
CLEANING
2. 2\b.
4.
RINSEWATER
3.
Power Swi\bchHea\ber Swi\bchPower Swi\bchPower Swi\bch
5.
Keep plenty of gen\fine  bISSEll 
adv\bnced  cle\bning form\fl\bs on h\bnd so 
yo\f c\bn cle\bn whenever it fits yo\fr   
sched\fle.  alw\bys \fse gen\fine  bISSEll 
deep cle\bning form\fl\bs. Non-bISSEll 
cle\bning form\fl\bs m\by h\brm the 
m\bchine \bnd void the w\brr\bnty.
  W aRNING: to red\fce the risk of fire \bnd 
electric shock d\fe to intern\bl   
component d\bm\bge, \fse only   
b ISSE ll cle\bning fl\fids intended   
for \fse with the deep cle\bner. 
						

							Operation 
Carpet c\beaning (continued)
6. after cle\bning, yo\f m\by w\bnt to t\frn the  c\fstom 
c le\bn di\bl to rinse to give yo\fr c\brpeting \b   
fin\bl w\bter only rinse.  this will ens\fre thoro\fgh 
remov\bl of embedded dirt loosened by the   
deep cle\bning form\fl\b.  bISSE ll deep cle\bning 
form\fl\bs cont\bin \bn \bnti-resoiling \bgent th\bt 
helps yo\fr c\brpets repel dirt \bnd keeps them 
looking good longer.
7.  Remove the tank from the base of the machine 
b\f lifting up on the tank carr\f handle. Carr\f like a 
bucket to a utilit\f sink or outside where \fou will 
dispose of the dirt\f water.
7\b.  Unlatch the top of the tank from the bottom b\f 
lifting up on the tank latch which is located on the 
back of the tank.
7b.  Remove the top of the tank b\f lifting up on the 
handle. 
Note how the lip on the top t\bnk sep\br\btes 
from the groove in the bottom t\bnk.  this 
pl\bcement is import\bnt when p\ftting the 
t\bnk b\bck together.
7c.  Lift the bottom portion of the tank; pour out dirt\f 
water toward the sink through the triangular 
shaped opening in the corner of the tank.
Note:  yo\f m\by notice h\bir & debris deposits on the 
c\brpet or in the t\bnk th\bt were loosened by the 
cle\bning \bction (especi\blly with newer c\brpets th\bt 
h\bve never been deep cle\bned before).  this debris 
sho\fld be picked \fp \bnd thrown \bw\by.
7d.  Fill the heav\f dut\f bladder with hand hot tap 
water, following instructions 1c through 1e on 
page 10.
Note: Remember to sec\fre the t\bnk l\btch in 
the b\bck \bnd test to m\bke s\fre it is sec\fre 
before picking \fp the t\bnk.  alw\bys check 
the level of cle\bning form\fl\b in the form\fl\b 
t\bnk \bt the s\bme time, \bnd refill \bs needed.
8.  W\bter rinse (option\bl) . Rinsing is an optional 
step that can be done during the cleaning   
process b\f switching from one of the clean   
settings on the Custom Clean dial to a water 
rinse setting, or it can be done after the carpeted 
area has been cleaned. Simpl\f choose the water 
rinse setting on the Custom Clean dial, and follow 
the same path as \fou did for cleaning, taking 
care to do a forward (wet) stroke b\f depressing 
the spra\f trigger, a backward (wet) stroke, and a 
forward and backward (dr\f) stroke, releasing the 
spra\f trigger. Continue this until the water \fou 
see coming up the nozzle is clear. 
12w w w . b i s s e l l . c o m 	
8.
7. 7\b.
7b. 7c.
7d. 
						

							Operation 
Carpet c\beaning (continued)
9. cle\bnShot.  CleanShot is an optional feature that 
can be used to fight tough stains. It can be used as 
either a tough stain precleaner (see page 10) or can 
be used during the deep cleaning process itself. 
To use CleanShot either as a precleaner or during 
deep cleaning, follow the instructions below.
a. Set Custom Clean for the desired setting.
b.  Press the CleanShot button and aim the 
focused stream onto the stain. Allow the 
formula to soak in for 30 seconds. 
c.  Run the machine over the stain to extract. 
Repeat as needed until the stain is gone.
D.  Rinse if desired.
C\beaning \fith attachments
yo\fr  pro he\bt 2X m\bchine comes eq\fipped with 
\b hose \bnd \bt le\bst one \btt\bchment for cle\bning 
st\birs, \fpholstery, \bnd more.
1.  Import\bnt! If using to clean upholster\f, 
check upholster\f tags. 
a.  Check manufacturer’s tag before cleaning. 
“W” or “WS” on the tag means \fou can 
use \four ProHeat 2X. If the tag is coded 
with an “X” or an “S” (with a diagonal stripe 
through it), or sa\fs “Dr\f Clean  onl\f”, do   
not proceed with an\f deep cleaning 
machine. Do not use on velvet or silk. If 
manufacturer’s tag is missing or not coded, 
check with \four furniture dealer.
b .  Check for colorfastness in an inconspicuous 
place.
c.  If possible, check upholster\f stuffing. 
Colored stuffing ma\f bleed through fabric 
when wet.
D.  Plan activities to allow upholster\f time to dr\f.
E.  Vacuum thoroughl\f to pick up loose debris 
and pet hair. Use a vacuum with a brush 
attachment and a crevice tool to clean in 
fabric folds.
13w w w . b i s s e l l . c o m 	
Adsdfdd  ghg bvh
cvbbj  jkn hnbj  jkvh
gcghh jj  jhffhl kl lgh
Manufac\burer’s \bag 
						

							14
 
WaRNING: to red\fce the risk of fire \bnd 
electric shock d\fe to intern\bl 
component d\bm\bge, \fse only 
b ISSE ll cle\bning form\fl\bs 
intended for \fse with the deep 
cle\bner.  Non-bISSE ll cle\bning 
form\fl\bs m\by h\brm the m\bchine 
\bnd void the w\brr\bnty.
Operation 
C\beaning \fith attachments (continued)
2.  Follow the instructions on pages 10 & 11 for filling the 
2-in-1 water tank and the formula tank.
3.  Set Read\fTools dial to the hose attachments setting. 
This will allow spra\f and suction from the hose. 
4.  Set Custom Clean dial for heav\f traffic, normal 
clean, light clean, or water rinse as desired.
5.  Attach the cleaning tool to the end of the hose.  
6.  Plug in and turn on the power switch and heater (if desired).
7.  Clean b\f pressing the spra\f trigger to spra\f solution 
onto the area to be cleaned. Slowl\f move the tool 
back and forth over the soiled surface. Release the 
spra\f trigger to suction soiled water. Continue to clean 
in the area, working in small sections, until no more 
dirt can be removed. Rinse (optional) and suction as 
needed.  c\b\ftion: Do no overwet.
8.  Remove and rinse tools in clean, running water. 
Dr\f and replace in the tool cadd\f.
9.  It is recommended that \fou suction clean water 
from the tap to rinse out the hose. 
10.  Before replacing lift end of hose and stretch out to 
ensure all water is cleared from hose.
11.  Coil flex hose around the tool cadd\f.
12.  Empt\f 2-in-1 water tank and rinse out, 
following the instructions on page 12.  
13.  Return Read\fTools dial to floor setting.
C\beaning f\buid section
Keep plenty of gen\fine  bISSE ll a dv\bnced  cle\bning 
f orm\fl\b on h\bnd so yo\f c\bn cle\bn \bnd   
protect whenever it fits yo\fr sched\fle.  alw\bys \fse 
gen\fine  bISSE ll deep cle\bning form\fl\bs. 
5.
9.
10.
  W aRNING: to red\fce the risk of   
inj\fry, be extr\b c\bref\fl 
when cle\bning st\birs. 
M\bke s\fre m\bchi ne is 
sec\fre \bnd level.
w w w . b i s s e l l . c o m 	
651 mL   
BISSELL 
Tough S\bain 
Precleaner
#0400-E
709 mL BISSELL   
2X Fibre Cleansing 
Ad\fanced Formula  
 
wi\bh Sco\bchgard
™ 
pro\bec\bor
#62E5-E
709 mL BISSELL 
2X Mul\bi-Allergen 
Ad\fanced Formula  
 
wi\bh Sco\bchgard
™ 
pro\bec\bor
#89Q5-E
709 mL BISSELL 
2X Pe\b S\bain & 
Odor Ad\fanced 
Formula  
 wi\bh 
Sco\bchgard
™ 
pro\bec\bor
#99K5-E
709 mL BISSELL 
2X Na\bural Orange   
Ad\fanced Formula  
 
wi\bh Sco\bchgard
™ 
pro\bec\bor
#83p3-E
473 mL   
BISSELL 2X 
Hard Floor 
Solu\bions
#56l9-E
709 mL BISSELL 
2X La\fendar 
Essence Ad\fanced 
Formula  
 wi\bh 
Sco\bchgard
™ 
pro\bec\bor
#34b5-E 
						

							Operation 
Stain remova\b
Do Not Del\by! attending to \bn \bccident soon \bfter 
it occ\frs ens\fres the most optim\bl cle\bn.  le\bving 
it for \bn extended period of time m\by c\b\fse it to 
set \bnd become perm\bnent.
1.  Blot up liquids with an absorbent cloth or paper 
towels. White materials are recommended because 
certain d\fes ma\f bleed and make the stain worse.
2.  Gentl\f scrape up an\f semi-solids with a spoon or 
spatula. Do not use a knife or other utensil with sharp 
edges because it could damage the carpet or upholster\f.
3.   If the area has dried, remove the remaining 
semi-solids and residue with a sweeper or vacuum.
4.  Be sure to test an\f spot removal formulas in an 
inconspicuous area first. This is important as some 
d\fes and materials could be damaged or discolored 
b\f cleaning solvents. If such a change should occur, 
tr\f a different solution or call a professional.
5.  If cleaning on Berber carpeting, gentl\f run \four 
machine over a hidden area. If no fuzzing occurs, 
continue cleaning in soiled area.
6\b.  Using the BISSELL Tough Stain Precleaner, spra\f 
evenl\f over soiled area. Do not overwet. Wait 3-5 
minutes. Gentl\f work the solution b\f blotting area 
with a clean, damp, color safe cloth.
6b. cle\bnShot.  CleanShot is an optional feature that can 
be used to fight tough stains. It can be used as either 
a tough stain precleaner (see page 10) or can be used 
during the deep cleaning process itself. To use CleanShot 
either as a precleaner or during deep cleaning, follow the   
instructions below.
a. Set Custom Clean for the desired setting.
b.  Press the CleanShot button and aim the 
focused stream onto the stain. Allow the   
formula to soak in for 30 seconds. 
c.  Run the machine over the stain to extract. 
Repeat as needed until the stain is gone.
D.  Rinse if desired.
15w w w . b i s s e l l . c o m 	 
						

							16w w w . b i s s e l l . c o m 	
Operation 
Stain remova\b (continued)
7. Clean using either the  flooR clEaNING,  or 
toolS setting on the  Re\bdytools di\bl.
Hard f\boor c\beaning
yo\fr  pro he\bt 2X model m\by h\bve come with \b 
h\brd floor cle\bning \btt\bchment \bnd  h\brd  floor 
Sol\ftions  form\fl\b. If not, these prod\fcts \bre 
\bv\bil\bble for p\frch\bse by cont\bcting the  bISSE ll 
c ons\fmer Services dep\brtment by phone.  the 
h\brd floor cle\bning \btt\bchment provides effective 
cle\bning for linole\fm, vinyl, \bnd tile floors.   
c \b\ftion: Do not \fse on \fnse\bled h\brdwood floors.
1.  Vacuum or sweep thoroughl\f to pick up an\f 
loose debris and pet hair.
2.  move an\f furniture, if needed.
3.  Empt\f an\f carpet cleaning formula back into 
the BISSELL bottle if stored in the formula 
tank. Fill water up to the "WATER" line and 
then fill to "FoRmULA" line with BISSELL 2X 
concentrated Hard Floor Solutions.
4.  Fill the 2-in-1 water tank with hand hot tap 
water and set aside.
5.  Attach the hard floor tool onto the bottom of 
the machine b\f hooking it into the nozzle and 
swinging it down until it clicks into place. 
6.  Check  Re\bdyt ools di\bl. It should be set on 
floor cleaning.
7.  Set the  c\fstom  cle\bn di\bl to normal clean.
8.  Plug into an outlet and turn the power 
switch and heater  oN ( I ).
9.  Slowl\f move the machine forward and back over 
hard floor surface one time while depressing   
spra\f trigger.  c\b\ftion: Do not overwet.
10.  Repeat the motion without pressing the 
spra\f trigger using the hard floor cleaning 
attachment to squeegee and suction up the 
dirt\f water.
  WaRNING: to red\fce the risk of fire, 
electric shock or inj\fry 
\fnpl\fg from o\ftlet before 
servicing.
5. 
						

							Hard f\boor c\beaning (continued)
11. Allow adequate time for floors to dr\f.
12.  Remove hard floor cleaning attachment, 
rinse and dr\f before storing.
13.  If an\f formula remains in the formula tank, 
pour it back into the BISSELL 2X   
concentrated Hard Floor Solutions bottle for 
use the next time.
14
.  Rinse out the formula tank.
Machine storage
once yo\fr cle\bning is complete, m\bke s\fre 
the 2-in-1 w\bter t\bnk is emptied, rinsed o\ft, 
\bnd dried before the next \fse.  the form\fl\b 
t\bnk c\bn rem\bin filled \bnd re\bdy to go, or it 
c\bn simply be emptied b\bck into the form\fl\b 
bottle if th\bt is more convenient.
Note: Store cle\bner in \b protected, dry \bre\b. 
Since this prod\fct \fses w\bter, it m\fst not be 
stored where there is \b d\bnger of freezing. 
f reezing will d\bm\bge intern\bl components 
\bnd void the w\brr\bnty.
Machine care
f or best res\flts, \b few simple steps c\bn \bss\fre 
yo\fr m\bchine is well m\bint\bined \bfter yo\fr   
cle\bning is complete.
1.  Turn power and heater switches  off ( O  ). 
Unplug the machine and wrap the power cord.
2.  After empt\fing the 2-in-1 water tank, rinse 
it out at a faucet with running hot tap water, 
taking care to clean underneath the heav\f 
dut\f bladder, and all around it.  
3.  The top half of the tank can be rinsed clean 
through the nozzle area. Also, pop out the red 
filter underneath the top half of the tank and 
rinse that out. Replace before putting the top 
and bottom halves of the tank together.
4.  Before \fou place the cleaned 2-in-1 water tank 
back onto the machine, simpl\f unscrew the floor 
nozzle using a Phillips head       screwdriver. This 
can be rinsed out at the faucet. Then replace 
back onto the machine b\f starting from the 
bottom of the nozzle and hooking the tabs into 
the holes on the bottom sides of the machine. 
Secure into place with the screw.  
  WaRNING: to red\fce the risk of fire, 
electric shock or inj\fry 
\fnpl\fg from o\ftlet before 
servicing.
Maintenance and car\Ve 
17w w w . b i s s e l l . c o m 	
Fil\ber
Tip:
Le\b all par\bs dry comple\bely 
before s\boring
3.
Operation  
						

							18w w w . b i s s e l l . c o m 	
Maintenance and car\Ve 
Machine care (continued)
5. The inside of the end caps b\f the brush rolls 
can be wiped out with a clean paper towel, 
or, if a more thorough cleaning is desired, the 
end caps can be taken off using a Phillips 
head       screwdriver and rinsed clean. 
Replace after cleaning.
6.  An\f loose hair or debris can be pulled from the 
brush rolls and thrown awa\f. For the most   
thorough clean before storage, follow directions 
on pages 18 & 19 for removal and replacement 
of the brush rolls and belts.
7.  To clean attachments that ma\f have been 
used, remove from hose and rinse in   
clean, running water. Dr\f and replace 
attachment in the tool cadd\f. Clean the hose 
b\f suctioning clean water from the tap. 
Before replacing, lift end of hose and stretch 
out to ensure all water is cleared from hose. 
Refer to page 14, illustrations 9 & 10.
8.  After carpet is dr\f, vacuum again to remove 
hair and fuzz.
Sma\b\b be\bt remova\b and rep\bacement
occ\bsion\bl repl\bcement of one or both belts 
m\by become necess\bry. If th\bt is needed, ple\bse   
follow the instr\fctions below.
1.  Turn off the machine, and unplug it from 
the outlet.
2.  Remove both the 2-in-1 water tank and the 
formula tank. Set aside.
3.  Unscrew the front nozzle and remove it. Set aside.
4.  Turn the machine on its side. 
IMpoR taNt: M\bke s\fre th\bt the cord side 
is down.
5.  Remove the clear end cap b\f unscrewing 
the 2 black screws. Take care not to drop 
the screws into the unit.
6.  Remove 1 silver screw.
7.  Remove pivot arm b\f gentl\f lifting up.
8.  Remove small brush belt.
9.  Replace small brush belt, and reverse 
steps above.
2
1
WaRNING:   to red\fce the risk of fire, 
electric shock or inj\fry, 
\fnpl\fg from the o\ftlet 
before servicing.
2.
3.
4. 5.
6. 7.
8. 9. 
						

							Maintenance and car\Ve 
Brush remova\b and \barge be\bt rep\bacement
br\fshes c\bn be removed for cle\bning or   
repl\bcement \bs needed. 
1.  Follow small belt removal Instructions on 
page 18.
2.  Remove brush rolls b\f pulling them off of 
the metal rods.
3.  Place cleaned or new brush rolls back onto the 
 rods.  make sure one washer is on each end of   
the rollers prior to sliding onto the rod. Be sure   
to let the rod slide through the bushing to   
insure proper fit.
4.  Re-attach the long belt on the bottom to the 
cogs of the small roller brushes.
5.  Place small belt over back roller and 
metal cog.
6.  Place pivot arm in place and screw in place 
using the silver screw.
7.  Re-attach clear end cap b\f tightening with 
the (2) black screws.
8.  Return front nozzle to front of unit, b\f 
latching from underneath and then securing   
with a screw.
  If \fou have an\f questions or are having trouble   
installing or replacing \fou belt(s) or brushes,   
please call  bISSEll cons\fmer Services
  WaRNING: to red\fce the risk of fire, 
electric shock or inj\fry, 
\fnpl\fg from the o\ftlet 
before servicing.
19w w w . b i s s e l l . c o m 	
2. 3.
4. 5.
6. 7.
8.
Troub\beshooting 
b \filt-in he\bter re\bdy light does not ill\fmin\bte
possible  c\b\fse   Remedies
1.  The heater switch is not turned  oN  (  I ).   1. Turn the heater switch  oN  (  I ).
2.   The power switch is not turned  oN  (  I ).   2. Both switches must be  oN  (  I ) to
     activate the heater read\f light.
Red\fce Spr\by or No Spr\by
possible  c\b\fse   Remedies
1.  2-in1 water tank ma\f be empt\f.  1. Fill heav\f dut\f bladder with hand hot 
     tap water. 
2.   Formula tank ma\f be empt\f.  2. Fill formula tank with water and 
     BISSELL 2X concentrated formula. 
3.   2-in-1 water tank ma\f not be  3. Turn power  off ( O ). Remove and 
  seated completel\f.    reseat tank.  
						

							20w w w . b i s s e l l . c o m 	
Troub\beshooting 
Red\fce Spr\by or No Spr\by (contin\fed)
possible  c\b\fse   Remedies
4.  Pump ma\f have lost prime.  4. Turn power  off ( O ) and then back 
     oN  (  I ). Wait one minute, then 
     depress spra\f trigger.  
Dirt lifter  power br\fshes do not t\frn
possible  c\b\fse   Remedies
1.  The brush belt is off or broken.   1. Turn power  off ( O  ) and unplug unit
     from outlet. Follow instructions on   
     page 18 & 19. 
2.   The unit is in the upright position.  2. Brushes onl\f rotate when unit is 
     reclined using the detent pedal.
3.   Circuit breaker ma\f have tripped.  3. Turn the machine  off ( O  ) and 
     unplug from outlet. Check to see if   
     foreign object is caught in brush roll.   
     Remove object. Plug machine back in 
     to reset circuit breaker.
cle\bner not picking \fp sol\ftion 
possible  c\b\fses   Remedies
1.  Read\fTools dial ma\f be at wrong setting.  1.  Set Read\fTools dial to either FL ooR 
       CLEANING  or T ooLS  setting.
2.  2-in-1 water tank ma\f not be seated properl\f.  2. Pick up both the 2-in-1 water 
       tank and formula tank and reseat   
       them so the\f fit snugl\f on the unit.
3 .  2-in-1 water tank ma\f not be    3.  Check to make sure the "lip" of 
  assembled properl\f.    the nozzle is securel\f hooked   
       into the groove on bottom of   
       Tank (see page 10).
4.  Solution or 2-in-1 water tank is empt\f.  4. Check fluid levels in heav\f dut\f 
       bladder and formula tank. 
5.  2-in-1 water tank has picked up   5. Empt\f 2-in-1 water tank. Refill 
  maximum dirt\f water and red float    heav\f dut\f bladder with clean    
  door has closed.     hand hot tap water and replace. 
6.  Red float "door" in the tank ma\f have closed   6. Turn the machine  off ( O ),  
  as a result of bumping an object or moving    allowing red float door to release into 
  machine back and forth too quickl\f.   the open position. Turn unit back   
       oN (  I ) to continue cleaning. Be 
       sure \four forward and backward   
       strokes are done at a slower pace.
o ther m\binten\bnce or service not incl\fded in the m\bn\f\bl sho\fld be performed by \bn   
\b\fthorized service represent\btive.
t h\bnk yo\f for selecting \b  bISSE ll prod\fct.
ple\bse do not ret\frn this prod\fct to the store.             
for UK inq\firies:
monday - Thursday  9 am — 5 pm  
  fr\bday  9 am — 4 pm 
bISSEll  homec\bre (overse\bs) Inc.
The Boat Yard   
105 Stra\bght Road   
old W\bndsor   
Berksh\bre, SL4 2SE 
\fn\bted K\bngdom   
Telephone: 0844-888-6644